Kenmore 11016852503 washer Parts

To hard reset your Kenmore washer model 11016852503, we recommend a simple power reset first: unplug the washer (or switch off the breaker) for 1 minute, then restore power and try a normal cycle. This clears minor control glitches and cycle “hang-ups.”

Quick hard reset steps (power reset)

• Turn the cycle control knob to Off.
• Unplug the washer from the outlet (or turn off the circuit breaker).
• Wait 60 seconds.
• Restore power.
• Close the lid and select a normal wash cycle.
• Pull out the cycle control knob to start.

If the washer still will not run: do these checks next

A “reset” will not fix a mechanical or safety-interlock problem. On this style of Kenmore top-load washer, the lid must be closed for the washer to run; a failed lid switch can stop agitation, spin, or drain.

• Confirm the lid is fully closed and the lid strike lines up.
• If the washer will not start or stops when it should spin, inspect the washer lid switch assembly WP8318084.
• If the washer hums but will not drain, check for a clog and consider the washer drain pump WP3363394.
• If the washer fills but will not agitate or spin, the washer motor coupling 285753A is a common wear item.

What “reset” means on this model (and what it does not)

This model uses a mechanical cycle control knob for starting and stopping cycles. A power reset clears temporary electrical issues, but it does not recalibrate a control board the way some digital-display washers do.

Situation	Best next step
Washer stuck mid-cycle	Power reset, then restart cycle
Will not start/spin with lid closed	Check lid switch function
Will not drain	Check drain hose, pump, and clogs
Excess vibration after moving washer	Re-level the washer per the installation guide

Why it matters

Resetting is the fastest way to clear a minor interruption, but checking the lid switch, drain pump, and motor coupling prevents repeat no-start, no-spin, and no-drain symptoms that look like “electronics” but are actually part or installation related.

Last updated: February 2026

Your Kenmore washer model number is printed on the appliance’s model and serial tag; for Kenmore model 11016852503, it’s typically under the lid on a top-load washer, inside the door opening on a front-load washer, or on the back panel near the power cord or control console. Confirm the full number before ordering parts.

Where to look on Kenmore washers

Check these common tag locations first:

• Under the lid, around the tub opening (top-load models)
• Inside the door opening on the front frame (front-load models)
• Back panel near the power cord entry
• Along the side of the cabinet near the control panel
• Occasionally behind the lower front access panel (some designs)

For diagrams and model-specific identification notes, use the 11016852503 owner's manual.

What the model number looks like (and why it matters)

Kenmore washer model numbers are often a long numeric string; many start with 110 (a common Kenmore prefix). Using the exact model number helps us match the correct fit for parts like a lid switch, drain pump, clutch, or motor coupling.

Quick check table

What you see on the tag	What to do	Why it matters
Full model number (example: 11016852503)	Use it exactly as printed	Ensures correct parts list and diagrams
Serial number	Record it too	Helps confirm production run details
Only partial digits	Re-check tag and cabinet areas	Prevents ordering the wrong part

Tips before you order parts

• Write the model number exactly, including all digits
• Take a clear photo of the tag for reference
• Match the model number to the parts list before checkout
• If you are troubleshooting a symptom, confirm the model first, then diagnose (for example, a no-spin issue can involve the lid switch, clutch, or motor coupling)

Why it matters

Kenmore washers can look similar across multiple series, but internal components and mounting styles change by model. Using 11016852503 ensures we point you to the right Kenmore washer parts and the correct installation details.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11016852503, good installation (level floor, correct water pressure, proper drain setup) and routine care help you reach the high end of that range; chronic overloading and poor draining shorten it. See the 11016852503 owner's manual for care and operating practices.

What affects washer lifespan the most

• Load size and balance: frequent overloading strains the drive system and suspension.
• Drain performance: slow draining makes the pump work harder and can leave water behind.
• Agitation and spin wear items: couplers, clutches, and agitator components wear with use.
• Installation conditions: a level, sturdy floor reduces vibration and component fatigue.
• Cold-weather storage: operating at or below 32°F can leave water that may damage components.

Common wear parts that can shorten life (and what they do)

If performance changes, these model-matched parts are common suspects:

Symptom	Likely area	Example model-matched part
Won’t drain or drains slowly	Drain system	Washer drain pump WP3363394
Won’t spin, intermittent agitation	Drive coupling	Washer motor coupling 285753A
Agitator “slips” or doesn’t move clothes well	Agitator dogs	Agitator dog 80040
Won’t spin with lid closed, stops mid-cycle	Safety interlock	Washer lid switch assembly WP8318084

Maintenance habits that extend life

• Keep loads evenly distributed; wash bulky items in pairs when possible.
• Use the right amount of detergent; excess suds can contribute to poor draining and residue.
• Periodically inspect fill hoses and the drain hose for kinks, rubbing, or leaks.
• If the washer will be in freezing conditions, follow the winterizing guidance in the installation guide.

Why it matters

Washer lifespan is mostly about reducing stress on the drive and drain systems. A stable installation and consistent care help prevent early failures in high-wear components like the drain pump, motor coupling, and lid switch.

Last updated: February 2026