Kenmore 11029532800 washer Parts

Kenmore washer model numbers are structured so the first 3 digits identify who manufactured the washer, and the remaining digits narrow it down to the exact design and variation. For Kenmore model 11029532800, the 110 prefix is the key manufacturer identifier.

What each section of the model number means

Most Kenmore washer model numbers break down like this:

• First 3 digits (prefix): manufacturer code (example: 110)
• Next group of digits: base model design (platform and major features)
• Last digits: specific variation (production changes, color, feature package)

If you are recording the information for parts or service, the model and serial label is typically located under the washer lid on this style of Kenmore top-load washer.

Why the prefix matters for parts

The prefix helps us match your washer to the correct parts diagrams and compatible replacement parts. Even small model variations can change which items fit, especially for drive and safety components.

Common examples of parts that can vary by model version include:

• Lid switch and harness connections
• Drain pump mounting and hose ports
• Drive system components (coupling, clutch, basket drive)
• Timer and knob style
• Agitator and dispenser style

What you’re doing	What to use	Why it helps
Ordering replacement parts	Full model number (all digits)	Ensures exact fit
Looking up diagrams	Full model number	Shows the correct component breakdown
Checking installation steps	Installation guide	Confirms hookups and safety steps

Why it matters

Using the full model number prevents wrong-part returns and speeds up troubleshooting. It is especially important on Kenmore washers because the same “Kenmore” brand label can be built by different manufacturers.

Last updated: February 2026

The exact tub capacity (cubic feet) for Kenmore washer model 11029532800 is typically listed in the specifications section of the product literature; for many Kenmore 110 top-load washers of this design, capacity commonly falls in the about 3.0 to 3.5 cu. ft. range. For the most accurate figure for your unit, check the 11029532800 owner's manual.

How to confirm the capacity on your washer

We recommend using one of these quick checks so you get the right number for comparing models, planning load sizes, or choosing replacement parts.

• Look for a “Capacity” or “cu. ft.” spec in the manual’s feature/specifications pages.
• Check the model and serial label under the washer lid (the manual notes this label location).
• If your manual lists basket/tub dimensions, use those to calculate an approximate volume.
• Compare your washer’s basket size to typical “standard” vs “super capacity” top-load tubs.

Typical capacity ranges (helpful benchmark)

These ranges help you sanity-check what you find in the manual.

Washer type (top load)	Typical capacity range	What it usually means
Standard capacity	~2.5 to 3.2 cu. ft.	Everyday mixed loads
Large capacity	~3.2 to 3.8 cu. ft.	Bulkier loads, fewer cycles
Extra-large capacity	~3.8 to 4.5+ cu. ft.	Comforters, large families

Why it matters

Capacity affects how full you can load the basket, how well the agitator circulates clothes, and how much strain is placed on drive components during agitation and spin. Overloading can contribute to poor cleaning and extra wear on parts like the coupling 285753A and clutch 285785.

Last updated: February 2026

To hard reset your Kenmore 11029532800 washer, unplug it for 1 minute, then plug it back in. This clears a temporary control “glitch” and restores normal operation without changing your cycle selections on this mechanical-timer style washer.

Hard reset steps (safe and quick)

• Turn the Cycle Control knob to Off.
• Unplug the washer from the wall outlet.
• Wait 60 seconds.
• Plug the washer back in.
• Close the lid.
• Select a cycle and pull out the Cycle Control knob to start.

If the washer is stuck mid-cycle

Our manual procedure for stopping and restarting is:

• To stop: push in the Cycle Control knob.
• To restart: close the lid (if open) and pull out the Cycle Control knob.

For model-specific operating steps and cycle behavior, use the 11029532800 owner's manual.

What a reset fixes (and what it usually does not)

Symptom	Reset helps?	What to check next
Washer pauses or seems “stuck” briefly	Often	Some cycles pause about 2 minutes; let it continue
Won’t agitate or spin	Sometimes	Lid must be closed; consider the washer lid switch assembly WP8318084
Won’t drain	Sometimes	Check for clogs; consider the washer drain pump WP3363394
Loud grinding or no spin with motor running	Rarely	Drive system parts like the coupling 285753A

Why it matters

A hard reset is the fastest way to clear a temporary interruption (power flicker, paused timer position, or an incomplete stop). If the problem returns right away, the washer is usually reacting to a real condition like an open lid, a drain restriction, or a worn drive component.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11029532800, unplug the washer, remove as much tub water as possible, then disconnect and flush the drain hose and clear debris at the pump inlet. Reinstall the hose at the correct height with an air gap to prevent siphoning.

Safety first

• Unplug the washer before handling hoses or the pump
• Turn off both water faucets
• Keep towels and a shallow pan ready
• Wear gloves; small items and sharp debris can be inside

Step-by-step: clear the clog

• Remove standing water: Scoop it out or use a wet/dry vac at the drain hose end.
• Check the standpipe end: Look for lint, coins, socks, or sludge right at the hose outlet.
• Flush the hose: Run water through the hose; work a plastic zip tie or small drain snake through to break up buildup.
• Inspect the pump inlet/impeller area: If the hose is clear but draining is still slow, debris is often at the pump. If the pump is jammed or leaking, replace the washer drain pump WP3363394.

Install it correctly (prevents siphoning and repeat clogs)

Use the drain setup guidelines in the installation guide. Key points:

• Top of drain hose: at least 39 in. (99 cm) above the floor
• Standpipe height limit: hose end not more than 96 in. (244 cm) above the floor
• Standpipe insertion: no more than 8 in. (20.3 cm) inside the standpipe
• Do not tape or seal the hose; it needs an air gap

Quick diagnosis table

Symptom	Likely cause	Next check
Won’t drain, water remains	Hose or pump inlet clogged	Flush hose; clear pump inlet/impeller
Fills and drains repeatedly	Siphoning	Hose height, air gap, insertion depth
Drains slowly	Partial blockage or kink	Kinks behind washer; sludge in hose

Why it matters

A restricted drain hose makes the washer stop mid-cycle, leave water in the basket, or drain poorly. Correct hose height and an air gap protect floors from leaks and help the drain pump move water efficiently.

Last updated: February 2026