Kenmore 10657039601 side-by-side refrigerator Parts

For Kenmore model 10657039601, the most reliable way to confirm cubic feet is to check the refrigerator’s rating plate inside the cabinet; it typically lists the unit’s total volume (capacity). If the label is missing or unreadable, you can estimate capacity by measuring the interior and converting to cubic feet.

Look for a rating plate or product data label in common spots such as:

• On an interior side wall (fresh food section)
• Behind or beside the crisper drawers
• Along the ceiling area inside the refrigerator compartment
• On the inside edge near the door opening
• Sometimes in the freezer compartment side wall

If you need help identifying label locations and interior components, use the 10657039601 owner's manual.

If you cannot read the rating plate, you can estimate capacity using interior measurements.

1. Measure interior height, interior width, and interior depth (in inches) of the main storage space.
2. Multiply: H x W x D = cubic inches.
3. Divide by 1,728 to convert to cubic feet.

• Measure the open cavity, not the door bins
• For a closer estimate, measure the refrigerator and freezer sections separately and add them
• Expect your estimate to be higher than “usable space” because shelves, bins, and the ice maker take up room

Knowing cubic feet helps us match the right replacement parts and accessories (like shelves, bins, and water filters), and it also helps when comparing side-by-side refrigerator sizes for fit and storage planning.

Last updated: February 2026

To replace the ice maker in your Kenmore 10657039601 side-by-side refrigerator, we turn the ice maker OFF, disconnect power, remove the ice bin and mounting screws, swap in the new assembly, then restore power and water. Use the 10657039601 owner's manual for switch location and ice maker operating details.

• Unplug the refrigerator to prevent electric shock.
• Turn the ice maker OFF using the On/Off switch in the freezer compartment (top right area).
• Shut off the household water supply to the refrigerator.
• Empty the ice storage bin; never use sharp tools to break up ice.
• Protect floors and the freezer liner from dropped screws.

1. Remove the ice storage bin from the freezer door.
2. Disconnect power and shut off water.
3. Remove the ice maker mounting screws and support the ice maker as the last screw comes out.
4. Unplug the ice maker wiring harness connector.
5. Install the replacement ice maker, reconnect the harness, and tighten mounting screws.
6. Turn water back on, plug the refrigerator in, and switch the ice maker ON.

If you are replacing the complete assembly for this model, use the exact replacement part refrigerator ice maker assembly 2198597.

It is normal for a new or replaced ice maker to take time to begin producing ice.

• Confirm the On/Off switch is set to ON.
• Make sure the ice bin is seated securely.
• Verify the water supply valve is fully open and the line is not kinked.
• Replace a clogged filter if water flow is weak; this model uses refrigerator water filter EDR3RXD1.
• If the ice maker is not filling with water, test the refrigerator inlet valve W10408179.

Correct installation and water flow protect the ice maker from damage and help prevent small cubes, hollow cubes, and slow production. Water quality also affects ice quality; avoid connecting to softened water when possible.

Last updated: February 2026

Most Kenmore side-by-side refrigerators measure about 33 to 36 inches wide overall, but the exact exterior width varies by series and door/handle style. For Kenmore model 10657039601, use the dimension diagram and installation clearances in the 10657039601 owner's manual to confirm your opening size.

When customers ask about width, we recommend checking these measurements so the refrigerator fits and the doors open fully:

• Cabinet width (box only, no handles)
• Overall width (doors and handles, if applicable)
• Opening width (wall-to-wall space where it installs)
• Door swing clearance next to a fixed wall
• Ventilation clearance at the sides and top

The manual for Kenmore 10657039601 calls out these clearances for airflow and door swing:

• Allow 1/2 inch space on each side and at the top for ventilation
• If installed next to a fixed wall, leave 2 inches minimum on each side (setup-dependent) so doors can swing open
• If the unit has an ice maker, allow extra space at the back for the water line connection

Use this approach before you move the refrigerator:

• Start with the refrigerator’s overall width from the manual
• Add 1/2 inch left + 1/2 inch right for ventilation
• Add more if a wall limits door swing

Correct width and clearance prevent poor airflow, warm temperatures, and doors that bind or hit a wall. It also helps avoid kinking the water line feeding the dispenser and ice maker.

Last updated: February 2026

Common Kenmore Elite refrigerator problems include warm temperatures (cooling failure), ice maker or dispenser trouble, water leaks, and odor or moisture issues. On Kenmore model 10657039601, these symptoms are often tied to airflow being blocked, water system issues, or defrost-related components; our 10657039601 owner's manual covers key operating and troubleshooting checks.

• Not cooling or uneven temps: blocked air vents, dirty condenser area, evaporator fan issues, or defrost system problems.
• Ice maker not making ice: water supply restriction, inlet valve problem, frozen fill tube, or ice maker assembly failure.
• Water dispenser slow or no water: clogged water filter, low house water pressure, or inlet valve issue.
• Leaking water: clogged defrost drain, loose water line connections, or a seeping inlet valve.
• Odors transferring between sections: uncovered foods and poor cleaning (air circulates between freezer and fresh food sections).

1. Confirm airflow: do not block the vents; blocked vents cause temperature and moisture problems.
2. Give it time after adjustments: temperature changes take time; wait about 24 hours for temps to stabilize.
3. Check the water filter status and flow: a restricted filter can affect both water and ice.
4. Listen for normal vs. abnormal sounds: fan noise changes can point to airflow or fan problems.
5. Inspect for visible leaks: look under the unit and around the inlet valve and water lines.

If the basic checks do not resolve the issue, these parts are frequent solutions on side-by-side refrigerators:

Air and water systems affect multiple symptoms at once. For example, blocked vents can cause warm temps and moisture, and a restricted filter or failing inlet valve can cause both dispenser and ice maker problems.

For model-specific operating details (controls, airflow, water system prep, and troubleshooting), use the 10657039601 owner's manual.

Last updated: February 2026

Most Kenmore refrigerators have a typical life expectancy of 10 to 15 years. For a Kenmore 10657039601 side-by-side refrigerator, regular care (especially cleaning and airflow maintenance) helps you reach that range and avoid early failures; our 10657039601 owner's manual outlines the maintenance and troubleshooting routines.

A refrigerator’s lifespan is driven less by the cabinet and more by wear items and cooling-system workload.

• Dirty condenser coils make the compressor run hotter and longer
• Worn door gaskets let warm air in, increasing run time and frost
• Poor airflow (overpacked shelves, blocked vents) causes temperature swings
• Water and ice system leaks can damage components and create icing
• Power interruptions and surges can stress electronic controls

Use this as a simple baseline for Kenmore side-by-side models.

These parts do not set the lifespan by themselves, but they are frequent repair points that can keep a refrigerator running longer when addressed early.

• Refrigerator inlet valve W10408179 if the ice maker or dispenser stops getting water
• Whirlpool refrigerator ice maker assembly 2198597 if ice production becomes inconsistent
• Refrigerator electronic control 4388932 if cooling cycles become erratic

A refrigerator that is running longer than normal (often from dirty coils or leaky door seals) wears the compressor and controls faster. Keeping temperatures stable and airflow clear reduces strain and extends service life.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10657039601, the model and serial number are printed on the appliance’s model and serial number label. Open the fresh food (refrigerator) door and look along the inside cabinet walls for the label; record the model and serial for parts and service.

• Open the fresh food door and scan the inside perimeter of the cabinet.
• Check the side walls near the front edge (eye level to mid-level).
• Look near the crisper drawer area on the inner cabinet liner.
• Check the ceiling area inside the fresh food compartment.
• If you do not see it in the refrigerator section, check the freezer door opening cabinet walls.

The tag is meant for product records and service calls, so it usually lists these items:

We use the exact model number to match the correct Kenmore refrigerator parts (like an ice maker assembly, water inlet valve, or defrost heater). Even small model number differences can change the correct part fit and wiring.

• Write down the model number and serial number exactly as shown.
• Keep it with your purchase records for quicker service.
• Use the model number to confirm maintenance items such as the correct water filter; for this model, a common replacement is genuine Kenmore refrigerator water filter EDR3RXD1.
• For diagrams and additional label location notes, check the 10657039601 owner's manual.

Last updated: February 2026

Many Kenmore refrigerators are built by Whirlpool; the quickest way to tell is the model number prefix. If your Kenmore model number starts with 106, it is a Whirlpool-built Kenmore, including Kenmore 10657039601. For confirmation details, check the 10657039601 owner's manual.

We use the first three digits (the prefix) of the Kenmore model number to identify who built the appliance.

Common Whirlpool-built Kenmore prefixes include:

• 106 (very common for Kenmore refrigerators)
• 110 (often laundry)
• 665 (often dishwashers)
• 198 (seen on some appliances)
• 552 (seen on some appliances)

Knowing the manufacturer helps you match the correct parts and service information for your exact refrigerator.

For Kenmore 10657039601, common maintenance and repair items include:

• Water filter (the manual lists replacement filter 9030)
• Ice maker components
• Water inlet valve
• Defrost system parts

If you are replacing the filter on this model, the manual calls out filter part 9030; our matching part page is genuine Kenmore refrigerator water filter EDR3RXD1.

If you are looking up diagnostics for Kenmore model families, use Kenmore 106 model refrigerator error codes.

Last updated: February 2026