KitchenAid KRFC704FSS01 bottom Parts

On the KitchenAid KRFC704FSS01, the bottom grill (base grille or toe grille) is held by two screws. We remove those screws with a 1/4-inch hex nut driver, then grasp the grille with both hands and pull it straight toward us to release it.

• Open the freezer drawer for better access.
• Use a 1/4-inch hex nut driver to remove the two screws in the base grille.
• Grasp the grille firmly with both hands.
• Pull the grille straight toward you to remove it.
• Set the grille and screws aside so they do not get lost.

Align the ends of the grille with the leveling assemblies on each side, then snap the grille into place and reinstall the two screws.

We remove the base grille to access the adjustable brake feet and front roller area. If the refrigerator feels unsteady or rolls forward when you open a door or the freezer drawer, adjusting the brake feet starts with removing this grille.

• Vacuum dust and pet hair from the grille and floor area to improve airflow.
• If the doors do not seal well after moving the refrigerator, inspect the refrigerator door gasket (gray) W10917313 for gaps, tears, or deformation.
• If you are ordering replacement parts for KRFC704FSS01, use the parts list for this model or search by model number on Sears PartsDirect.

For the exact procedure and illustrations for your model, follow the KRFC704FSS01 owner's manual.

Last updated: February 2026

To put shelves back in your KitchenAid KRFC704FSS01 bottom-mount refrigerator, insert the shelf at an angle, seat the rear into the shelf supports, then lower the front and press down so it locks firmly on the shelf mounts. Use both hands because the glass is heavy.

• Open the refrigerator doors to about a 90° angle for easier shelf handling.
• If your shelf mounts have a “flipper,” set the mounts to the height you want (vertical or horizontal position).
• Put the shelf into the compartment at an angle (front edge slightly down).
• Slide the shelf inward until the rear drops into the shelf supports.
• Lower the front edge, then apply gentle pressure on top to ensure it is fully seated.
• If you removed multiple shelves, reinstall the middle shelf before the top shelf.

Shelf height is controlled by the adjustable shelf mounts. We recommend changing all mounts for that shelf to the same orientation so the shelf sits level.

• Do not wash cold glass shelves with warm water; sudden temperature change can break the glass.
• Avoid bumping the shelf edges on the liner or door bins.
• Keep “infinity slide” style glass pushed back before tilting the shelf during removal or install.

A shelf that will not lock in place is usually caused by a mount flipped the wrong way, a shelf not fully seated in the rear supports, or a warped/loose support.

• Recheck that the rear is fully dropped into the supports
• Confirm all shelf mounts are set to the same position
• Inspect supports for cracks or looseness
• If the shelf hardware is damaged, match the replacement using the parts list for KRFC704FSS01 or search by model on Sears PartsDirect

A properly seated shelf prevents rattles, reduces the chance of glass breakage, and keeps airflow consistent so the refrigerator maintains stable temperatures.

For diagrams and model-specific shelf styles, use the owner's manual.

Last updated: February 2026

The most common issues we see on KitchenAid refrigerators like model KRFC704FSS01 are temperature problems (too warm or inconsistent cooling), ice maker problems (no ice or low ice production), and water leaks from loose or restricted water connections. Use the KRFC704FSS01 owner's manual troubleshooting tables to pinpoint the cause fast.

• Temperature too warm: often normal right after install; allow 24 hours to cool fully, then recheck settings.
• Compressor seems to run a lot: high-efficiency compressors commonly run longer at lower speeds; hot rooms and warm food loads increase run time.
• No ice or low ice: a jammed cube, low water pressure, or a clogged filter can reduce ice production.
• Small or hollow cubes: typically points to low water pressure or a shut-off valve not fully open.
• Water leaking (especially after door removal): commonly caused by a water line connection that is not fully tightened.

1. Confirm the refrigerator is plugged into a grounded 3-prong outlet (no extension cord).
2. Verify the outlet has power; reset a tripped breaker or replace a blown fuse.
3. Make sure controls are turned on and not in Showroom mode.
4. If ice is weak, remove any jammed cube and confirm the shut-off valve is fully open.
5. If you suspect a filter restriction, replace the water filter and retest.

Cooling and ice maker issues can lead to food spoilage, poor ice production, and extra compressor run time. Catching a simple cause (like a clogged filter or loose water line) can prevent bigger repairs.

For model-specific operating steps and troubleshooting, follow the KRFC704FSS01 owner's manual. If you need to order parts for this refrigerator, start with the parts list for KRFC704FSS01 or search by model on Sears PartsDirect.

Last updated: February 2026

The KitchenAid KRFC704FSS01 overall height, width, and depth are listed in the dimensions/specifications section of the KRFC704FSS01 owner's manual. For planning your space, we can confirm key installation clearances from the manual, including rear clearance and minimum doorway width for delivery.

From the manual for this model:

• Leave 3 3/4 in. (9.5 cm) minimum space between the refrigerator and the wall (door swing and airflow)
• Allow 1/2 in. (1.25 cm) clearance (fit and airflow)
• Minimum door opening for delivery is 33 in. (838 mm)
• If the door opening is 36 in. (914 mm) or less, remove doors, drawer, and hinges for delivery

Refrigerator dimensions are usually shown in a diagram and may be listed in more than one way (cabinet only vs. with handles). Use these steps so you pull the right numbers from the manual:

• Look for overall width (often 36-inch class models are close to 36 in. wide)
• Check overall height (floor to top of hinge cover)
• Check overall depth in two ways: cabinet depth and depth with doors/handles
• Match the diagram to your install type (freestanding vs. counter-depth alignment)
• Compare the manual’s numbers to your measured opening and delivery path

Using the KRFC704FSS01 manual’s exact dimension diagram prevents delivery surprises and helps avoid restricted airflow, which can lead to temperature swings and poor ice production.

Last updated: February 2026