Fisher & Paykel DD605BK-88464A dishwasher dish drawer Parts

For the Fisher & Paykel DD605BK-88464A DishDrawer dishwasher, the installation guide lists an overall width of 595 mm and overall depth of 570 mm (excluding handle/curvature). Overall height depends on configuration: 409 mm for a single drawer, or 819.5 to 879.5 mm for a double drawer installation.

Dimensions for DD605BK-88464A (from the installation guide)

Use these measurements when planning cabinet cutouts, toe-kick clearance, and drawer opening space. See the installation guide for the full dimension diagrams.

• Overall width: 595 mm
• Overall depth (product): 570 mm (excluding handle/curvature)
• Drawer open depth: 520 mm (excluding handle/curvature)
• Single drawer overall height: 409 mm
• Double drawer overall height range: 819.5 to 879.5 mm (leveling feet adjustment range included)

Quick reference table

Setup	Overall height	Overall width	Overall depth
Single DishDrawer	409 mm	595 mm	570 mm
Double DishDrawer	819.5 to 879.5 mm	595 mm	570 mm

Cabinet opening (cavity) sizing tips

The cabinet opening is typically slightly larger than the product so the unit can slide in and be leveled.

• Plan for an inside cavity width around 600 mm
• Plan for an inside cavity depth around 580 mm
• Allow 13 mm minimum clearances where specified
• Keep services (water, drain, power) positioned so hoses route smoothly without kinks

Why it matters

Correct dimensions prevent installation problems like a drawer that rubs the cabinet, a toe-kick that interferes with opening, or hoses that kink and cause fill or drain issues.

Last updated: February 2026

To use your Fisher & Paykel DD605BK-88464A DishDrawer dishwasher, press Power, choose the drawer you want to run, select a wash program (like Rinse or Normal), then close the drawer and press Start/Pause to begin.

Basic steps (everyday use)

• Load dishes so the spray arm can rotate freely.
• Add detergent to the dispenser (use rinse aid if your model is equipped).
• Press Power; the cycle lights should come on.
• Select the drawer (top or bottom) you want to wash.
• Choose a wash program (for a quick test, use Rinse).
• Close the drawer fully, then press Start/Pause.

Quick “first run” check (after install or after moving the unit)

The installation checklist for DD605/DS605 models recommends a simple rinse test to confirm filling, washing, and draining.

1. Turn on water supply and power.
2. Press Power.
3. Confirm the spray arm is installed and spins freely.
4. Add about 3 cups of water into the drawer.
5. Select Rinse, close the drawer, and press Start/Pause.

If it won’t start or doesn’t drain

Most start and drain issues come from the drawer not closing freely, a kinked drain hose, or a blocked waste connection.

Symptom	What to check first	Common fix
Drawer won’t close	Hoses, insulation, tub latches	Clear obstruction; re-seat drawer
Water left above filter plate	Kinked hose, blocked drain, high loop routing	Straighten hose; clear blockage
No water supply message	Water turned off; spray arm not fitted	Turn on water; re-fit spray arm

If you suspect poor wash performance, also check for a worn or blocked spray arm; the dishwasher spray arm 527475 is a common wash-circulation part for this model.

Why it matters

Correct drawer selection, a fully closed drawer, and a freely rotating spray arm are the difference between a normal wash and problems like poor cleaning, standing water, or mid-cycle stopping.

For control-panel and installation-specific details (including hose routing and the final checklist), follow the installation guide.

Last updated: February 2026

To get your Fisher & Paykel DD605BK-88464A DishDrawer to drain, make sure the drain hose is routed correctly with no kinks or sagging, the waste connection is not blocked, and the filters are clean. A proper high loop and clear drain path fix most draining problems.

Quick checks that fix most “won’t drain” issues

• Cancel the cycle and restart a Rinse cycle to force a drain at the end.
• Pull the drawer out slightly and inspect the drain hose for kinks or crushing.
• Confirm the hose runs straight into the waste connection (no sharp bends).
• Make sure the high loop is installed; keep excess hose on the dishwasher side of the loop.
• Check the sink trap or standpipe connection for a blocked knockout/plug.
• Clean the filters: remove debris from the drain area and reinstall parts fully seated.

Drain hose routing (what “correct” looks like)

The installation requirements matter because a low, sagging hose can trap water and slow or stop draining.

Item to verify	What you want	What happens if it’s wrong
High loop	High loop installed; keep hose extended to prevent sagging	Water can sit in the hose and backflow
Hose path	No kinks; smooth bends	Pump cannot push water out
Waste connection	Knockout/plug removed; connection clear	Water has nowhere to go
Excess hose	Not hanging on the drain connector; stored on dishwasher side of loop	Connector can be stressed; hose can sag

Parts that commonly solve a drain problem

If routing and blockages check out, a clogged filter or a failing drain component is usually next.

• Clean or replace the drain filter 524828 if it is damaged or won’t clean up.
• If the drawer fills and washes but will not pump out, the dishwasher pump motor 522088 is a common suspect.

Why it matters

A DishDrawer that cannot drain will leave water above the filter plate, can trigger cycle interruptions, and can cause poor cleaning because dirty water stays in the tub. Correct hose routing and clean filters protect the pump and keep cycles finishing normally.

For the exact routing options (standpipe vs sink trap) and the final drain test steps, follow the installation guide.

Last updated: February 2026

On a Fisher & Paykel DD605BK-88464A DishDrawer, an F24 display is treated as a motor-related fault (the wash motor is stalled, stopped, or overloaded). The fastest path to a fix is to check for binding or debris first, then test the motor circuit components if the code returns.

What to do first (safe, quick checks)

• Turn power off at the breaker for 1 minute, then restore power and run a short rinse.
• Pull out the drawer and confirm it slides freely and closes fully (no rubbing on cabinetry).
• Remove and clean the filter area; clear labels, bones, glass, or hard debris.
• Check the spray arm spins freely by hand; remove anything that blocks it.
• If the unit is not draining well, correct drain hose routing and the required high loop.

Parts that commonly cause an F24 motor fault on this model

If the fault comes back after the checks above, these DD605BK-88464A parts are the most common causes:

• Dishwasher pump motor 522088 (motor seized, weak, or not starting)
• Motor rotor 524285P (rotor jammed or worn)
• Dishwasher hall sensor 528785P (motor position feedback issue)
• Controller 523456 (motor drive/control problem)

Installation items that can trigger repeat motor faults

A pinched hose, poor leveling, or drawer drag can overload the motor. Use the installation guide to confirm clearances, leveling, and hose routing.

Quick install checklist

• Drawer opens and closes with no resistance
• Hoses and wiring are not pinched behind the unit
• Drain hose runs smoothly to the waste connection with a high loop

Symptom-to-cause guide

What you notice	Most likely cause	What we recommend
Humming, no wash action	Jammed rotor or failing motor	Clear debris; inspect motor rotor 524285P and dishwasher pump motor 522088
Starts then stops	Overload or feedback problem	Check for binding; inspect dishwasher hall sensor 528785P
Intermittent faults, odd behavior	Control issue	Inspect wiring; consider controller 523456

Why it matters

When the wash motor cannot turn normally, the dishwasher cannot circulate water through the spray arm, so cleaning stops and the control may pause the cycle to protect the motor and electronics.

Last updated: February 2026