Kenmore 11028837700 washer Parts

Most Kenmore washers, including model 11028837700, typically last 10 to 15 years with normal household use. You can often reach the high end of that range by keeping loads balanced, using the right amount of detergent, and staying ahead of wear items listed in the 11028837700 owner's manual.

• Overloading and unbalanced loads: increases stress on the drive system and suspension.
• Water leaks and hose failures: can cause corrosion and secondary damage.
• Drain problems: running with restricted draining strains the pump and can leave standing water.
• Lid switch issues: can stop cycles and lead to repeated restarts and wear.
• Routine care: cleaning, proper leveling, and correct installation conditions matter.

The manual for this washer family calls out a key interval: replace inlet hoses every 5 years to reduce the risk of hose failure. We also recommend these habits:

• Replace inlet hoses on schedule; inspect for bulges, cracking, or seepage
• Keep the washer level and on a solid floor (reduces vibration and wear)
• Avoid chronic overloading; let items move freely during wash
• Check pockets and reduce debris that can clog the drain path
• Address slow draining early; a failing pump like the washer drain pump WP3363394 is a common wear item

A washer usually does not fail all at once; small issues (vibration, slow drain, intermittent stopping) often signal a part wearing out. Catching those early helps prevent secondary damage to the motor, gear case, or basket drive components.

Last updated: February 2026

On Kenmore washer model 11028837700, a 5d code is the same as Sd/Sud and means the washer detected excessive suds. The washer may pause and run a suds-reduction routine; let the cycle continue and correct the detergent/soap issue before the next load.

• Press Pause/Cancel only if the washer is stuck for an extended time; otherwise let it finish the routine.
• Use HE detergent only (if your detergent is not HE, switch).
• Reduce the amount of detergent; most oversudsing is simply too much soap.
• If you used regular detergent, run a Rinse/Spin (or a rinse cycle) with no detergent.
• Check for too many suds from additives (extra boosters, too much fabric softener, hand-wash soap).

Excess suds can slow draining and spinning, leave residue on clothes, and make the washer work harder than it should. Correcting the detergent amount helps the washer complete cycles normally and reduces repeat error codes.

• Follow detergent and loading guidance in the 11028837700 owner's manual.
• If you are installing or rechecking power/grounding, use the 11028837700 installation guide and follow the grounded 3-prong outlet requirements.

Last updated: February 2026

The exact tub capacity (cubic feet) for Kenmore washer model 11028837700 is listed in the product specifications section of the 11028837700 owner's manual. For most Kenmore 110-series top-load washers of this design, capacity commonly falls in the 3.2 to 3.5 cu. ft. range.

We recommend using the manual specs because capacity can vary even within the Kenmore 110 family.

• Open the 11028837700 owner's manual
• Look for “Specifications”, “Capacity”, or “Washer dimensions”
• If the manual lists basket size in gallons or liters, convert to cubic feet (see table below)
• If you cannot find a capacity line, check for a model tag under the lid and match it to the spec page in the manual

Capacity affects load sizing, cycle performance, and water usage. If you routinely overload a smaller-capacity top-load washer, you can get poor agitation, out-of-balance spinning, and extra wear on drive components like the clutch and motor coupling.

Last updated: February 2026

Your Kenmore washer model number is printed on the model and serial number label. On Kenmore model 11028837700, that label is located under the washer lid; write down the full model number and serial number exactly as shown and use it to match the correct washer parts and diagrams in our system. See the 11028837700 owner's manual for the exact label location and how it’s recorded.

Most Kenmore washers place the model tag in one of these spots:

• Top-load washers: under the lid (often along the rim of the opening)
• Front-load washers: inside the door opening (around the door frame)
• Some models: on the back panel near the power cord or control area
• If the tag is worn: use a flashlight and look for faint stamped or printed characters

Record these items exactly as they appear on the label:

• Model number (for this page: 11028837700)
• Serial number (helps confirm production details for service)
• Purchase date (useful for maintenance tracking)

Kenmore model numbers can look similar, and a single digit difference can change the correct fit for parts like a lid switch, drain pump, or motor coupling. Using the full model number helps prevent ordering the wrong replacement.

Once you confirm 11028837700, these are common part categories customers look up:

• Lid switch and safety interlock
• Drain pump and hoses
• Agitator components
• Drive system parts (coupling, clutch)

For example, if the washer will not spin because the lid is not registering as closed, the washer lid switch assembly WP8318084 is a common match for this model.

Last updated: February 2026