Kenmore 11044826300 washer with horizontal axis Parts

On the Kenmore 11044826300 front-load washer, a clogged drain hose is usually cleared by safely draining any standing water, checking for kinks or a blocked standpipe connection, then removing the hose and flushing out debris. Use the routing and height limits in the 11044826300 owner's manual to prevent repeat clogs.

• Unplug the washer to prevent shock.
• If the tub is full, run DRAIN/SPIN to drain it; if the water level is too high, the washer may drain automatically before the door unlocks.
• Pull the washer forward and inspect the drain hose for a kink, pinch, or freeze.
• Disconnect the drain hose from the home drain (standpipe or laundry tub) and check the end for lint, coins, or a sock.
• If needed, remove the hose from the washer side and flush it with hot water; a small drain snake or straightened coat hanger helps push out a clog.
• Reinstall the hose and clamps securely, then run a DRAIN/SPIN test.

The drain hose setup matters as much as the clog removal.

• Keep the hose secure but not airtight at the standpipe so there is an air gap.
• Do not force excess hose down into the standpipe.
• Do not lay excess hose on the bottom of a laundry tub.
• Confirm the standpipe height is not more than 96 in. (2.4 m) above the floor.

If the hose is clear but the washer still will not drain, the drain pump or the tub-to-pump path is often restricted. For this model, common related parts include the water pump 280187 and the washer tub-to-pump hose WPW10467168.

A restricted drain can trigger F02 errors, leave water in the drum, and cause poor spin performance. Correct hose routing and standpipe height also reduce siphoning and repeat drain complaints.

Last updated: January 2026

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 11044826300 horizontal-axis washer, lifespan depends most on load size, detergent use (especially HE detergent), and how well you prevent drain and door-boot issues; routine care can keep it running closer to the high end.

• Usage level: daily heavy loads shorten life compared to moderate weekly use.
• Maintenance habits: cleaning and inspection reduce wear and leaks.
• Water quality: hard water can increase buildup and stress valves and seals.
• Drain health: coins, lint, and debris strain the pump and hoses.
• Vibration control: an unlevel washer increases wear on suspension and tub components.

Common symptoms that signal major wear (and often drive repair decisions):

• Won’t drain or drains slowly
• Loud rumbling during spin (bearing or tub wear)
• Door won’t lock or unlock reliably
• Leaks at the door area or underneath
• Excessive shaking or walking

If the washer is otherwise in good shape, these repairs are often worthwhile:

Knowing the typical 10 to 15 year life expectancy helps you decide whether to repair or replace. If your 11044826300 is within that range, fixing a drain, fill, or door-lock problem often restores reliable operation for years.

For model-specific care and maintenance intervals, follow the Kenmore 11044826300 owner’s manual.

Last updated: January 2026

On Kenmore washer model 11044826300, turn off Control Lock by pressing and holding DRAIN/SPIN for 3 seconds until the CONTROL LOCKED status light turns off. This same 3-second press toggles the lock back on. See the 11044826300 owner's manual for the exact button location on your control panel.

• Power the washer on (the display or status lights should be lit).
• Locate the DRAIN/SPIN button.
• Press and hold DRAIN/SPIN for 3 seconds.
• Verify the CONTROL LOCKED light turns off.
• Test a cycle button to confirm the panel responds.

• Hold the button a full 3 seconds (a quick tap will not toggle the lock).
• Make sure you are holding DRAIN/SPIN, not PAUSE/CANCEL.
• If a cycle is running, press PAUSE/CANCEL once, then try the 3-second hold again.
• Restore power by unplugging the washer for 1 minute, then retry the 3-second hold.

When CONTROL LOCKED is lit, most buttons are disabled to prevent unintended cycle or option changes.

Control Lock is a common reason a washer seems unresponsive even though it has power. Unlocking restores normal button function so you can change cycles, options, and start a new load.

Last updated: January 2026

Kenmore model 11044826300 is a front-loading (horizontal-axis) washer; capacity is measured in cubic feet, and the exact number for your unit is listed in the specifications section of the 11044826300 owner's manual. Most full-size front-load washers are commonly in the 3.0 to 4.5 cu. ft. range.

Use the manual to confirm the official spec for your washer.

• Open the 11044826300 owner's manual.
• Look for “Specifications” or “Product dimensions” and the line for “Capacity” (often shown as cu. ft.).
• If the manual lists a series (for example, 110.4282, 110.4482, 110.4483), match the full model number on your washer’s rating label.
• Keep the capacity handy when choosing cycle settings for bulky items.

Correct loading protects tumbling action and helps prevent spin issues.

• Load items loosely; do not pack them down.
• Fill the drum no more than about 3/4 full for mixed everyday loads.
• Wash bulky items (comforters, jackets) one at a time or as a balanced pair.
• If the washer bangs or will not reach high spin, reduce the load and redistribute.

Capacity affects how well clothes tumble, rinse, and spin. Overloading increases vibration and can contribute to wear on parts involved in spinning and draining, such as the washer drive belt WPW10388414 and water pump 280187.

Last updated: January 2026