Bosch SHE4AM16UC/01 dishwasher Parts

Yes, most Bosch built-in dishwashers (including the Bosch SHE4AM16UC) are designed to fit a standard 24-inch-wide opening, while some Bosch models are compact 18-inch-wide units. For exact cutout and clearance requirements, use the measurements in the SHE4AM16UC installation guide.

Most kitchens in the U.S. are built around these common dishwasher sizes:

• Standard built-in: about 24 inches wide
• Compact built-in: about 18 inches wide
• Height and depth: vary by model and installation method (leveling legs, toe panel clearance, countertop height)

We recommend checking these items before ordering parts or planning an install:

• Cabinet opening width (inside-to-inside)
• Opening height (floor to underside of countertop)
• Depth to the back wall, including plumbing and electrical clearance
• Toe-kick clearance so the toe panel fits and the door opens freely
• Mounting method (to countertop or side cabinets) and bracket clearance

For the model-specific numbers and diagrams, follow the cutout and leveling instructions in the SHE4AM16UC installation guide.

A dishwasher that is even slightly too tall, too deep, or too wide can bind the door, rub the toe panel, or make it hard to secure the unit properly. Confirming the cutout dimensions first prevents installation problems and helps ensure proper draining and leak protection.

Last updated: February 2026

For Bosch dishwashers like model SHE4AM16UC, the most common problems are maintenance-related: restricted water flow from a dirty filter or clogged spray arms, which leads to poor cleaning and sometimes draining complaints. Checking for simple blockages first prevents many “no drain” and “not cleaning” calls; see the owner's manual.

• Clogged filter or sump area: gritty residue, standing water, or bad odors.
• Spray arm blockage: dishes stay dirty, especially on the top rack.
• Drain path restriction (air gap, disposer inlet, hose kink): water left in the tub.
• Drain pump trouble: humming, intermittent draining, or no drain at end of cycle.
• Door seal leaks: water at the front corners or along the bottom edge.
• Fill problems (inlet valve or supply issue): cycle runs “dry” or cleans poorly.

1. Turn off power at the breaker.
2. Remove and clean the filter assembly; rinse under hot water.
3. Spin spray arms by hand; clear debris from the holes.
4. Inspect the drain hose routing for kinks and confirm a proper high loop.
5. If connected to a garbage disposer, make sure the disposer inlet knockout plug was removed.

If cleaning and hose checks do not fix it, these model-matched parts are common next steps:

Most Bosch dishwasher “failures” start as restricted flow. When water cannot circulate or drain correctly, detergent does not dissolve well, sensors can misread conditions, and cycles may end with residue or standing water.

For code-related symptoms, use Bosch dishwasher error codes to match the display to the most likely cause.

Last updated: February 2026

To clear an error code on your Bosch SHE4AM16UC dishwasher, we reset (cancel) the current cycle so the control drains and returns to standby. On most Bosch models, this is done by pressing and holding the Start/Reset key for about 3 seconds, then letting the unit drain.

• Press and hold Start/Reset (often labeled Reset 3 sec) for 3 seconds.
• Close the door and wait for the drain/pump-out to finish.
• When the display returns to standby, select a new cycle and press Start.
• If the error returns immediately, turn the dishwasher off, then restore power at the breaker after 5 minutes and try again.

A reset usually triggers a drain. If water stays in the tub, the issue is often a blockage or a drain component problem.

• Check the sink/disposer connection for a clog.
• Inspect the drain hose for kinks or a high loop problem.
• Clean the filter area in the bottom of the tub.
• If the pump hums but does not move water, the drain pump may be jammed or failing.

Helpful parts commonly involved in drain problems:

• Drain pump 00611332
• Dishwasher drain hose 00668108
• Valve 00611320

Bosch error codes are the dishwasher’s way of protecting the wash system (pump, heater, sensors, and water level). Resetting clears the active program, but repeated codes usually point to a drain, fill, or sensing issue that needs troubleshooting.

For model-specific button sequences and any displayed code meanings, use the owner's manual and our Bosch dishwasher error codes reference.

Last updated: February 2026