Kenmore Elite 11097086601 dryer Parts

PF on the Kenmore Elite 11097086601 dryer means a power failure or power interruption was detected. To clear it, press Pause/Cancel/Stop twice; the display should return to normal once the control resets.

PF is triggered when power to the dryer is interrupted, even briefly. Before you run another cycle, we recommend these quick checks:

• Make sure the dryer plug is fully seated in the outlet
• Check the house breaker; reset it fully OFF then back ON if it tripped
• Avoid using an extension cord; plug the dryer directly into a proper outlet
• If you recently replaced the cord, recheck the terminal block connections (power off first)
• Start a cycle and watch for PF returning within the first minute

For control-panel behavior and cycle details specific to this model, use the 11097086601 owner's manual.

Repeated PF usually points to an unstable power supply or a connection issue. Use this quick guide to narrow it down.

A dryer that loses power mid-cycle can stop heating and tumbling, which increases dry time and can leave loads damp. Clearing PF is simple, but fixing the underlying power interruption prevents repeat shutdowns.

If you’re replacing a damaged cord or connection hardware, match the part to your setup and local electrical requirements. One common replacement item listed for this model is the power cord W11628810. You can also find additional replacement parts for model 11097086601 on this page or search by model at Sears PartsDirect.

Last updated: February 2026

On Kenmore Elite dryer model 11097086601, the L2 error means the dryer is not getting proper power on the L2 leg of the 240-volt supply (typically the L2 voltage is too low). Restoring correct 240V power usually clears the code and gets the dryer heating and running normally.

• Reset both dryer breakers (or replace blown fuses) in the home electrical panel; a dryer can run on 120V but still show L2 and not heat.
• Verify the outlet is supplying about 240 VAC across the two hot legs (L1 to L2) and about 120 VAC from each hot leg to neutral/ground.
• Unplug the dryer and inspect the terminal block connections for loose, burned, or melted wiring.
• If the cord or plug shows heat damage, replace the cord with the correct type for your outlet; use the wiring diagram in the 11097086601 owner's manual.
• If the outlet tests wrong, correct the house wiring or receptacle issue before troubleshooting the dryer further.

Your dryer needs both hot legs (L1 and L2) to deliver full 240V for the heater circuit. When L2 is missing or low, the drum may tumble but the burner or heater will not operate correctly, and the control can display an L2 code.

Once you have confirmed proper voltage at the outlet and terminal block, move to heating-system troubleshooting. On gas models, common heat-related parts include the igniter and sensors.

• Check the igniter and flame sensing circuit; a failed igniter can prevent burner ignition.
• Consider the igniter 279311 if the igniter does not glow during a heat call.
• If the dryer overheats and shuts down, inspect airflow and safety cutoffs; a failed cutoff can stop heat.

You can order replacement parts for Kenmore Elite 11097086601 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

For Kenmore Elite dryer model 11097086601, the drum belt size is determined by the exact belt part number used on your unit; most Kenmore 110-series dryers commonly use a multi-rib belt around 92 to 93.5 inches long and about 1/4 inch wide. For the exact match, confirm using the parts list and diagrams in the 11097086601 owner's manual.

Use these quick checks to avoid ordering the wrong belt:

• Match the model number exactly: 11097086601
• Look up the drum/bulkhead or motor and blower diagram where the belt routes
• If you still have the old belt, read the printed part number on it
• Compare belt style: multi-rib (grooved) belts are common on this platform
• If the belt broke, inspect the idler and rollers at the same time (they often cause repeat failures)

A worn belt is often a symptom of drag or misalignment. These parts are common companions during a belt job:

• Dryer idler pulley 279640 (keeps belt tension correct)
• Support WPW10314173 (drum support roller that can seize or flatten)
• Dryer repair kit 4392067 (often used to refresh multiple wear items at once)

Using the correct belt length and rib profile keeps the drum speed stable, prevents slipping, and reduces strain on the drive motor. On gas dryers like many Kenmore Elite models, proper airflow and drum speed also help drying performance stay consistent.

We recommend ordering by model number (11097086601) from the parts list for your dryer, or searching by model on Sears PartsDirect to ensure the belt and related maintenance parts match your exact configuration.

Last updated: February 2026