Error Codes
Does a gas dryer need a special outlet?
For the Kenmore gas dryer model 11087984110, you typically do not need a special 240-volt dryer outlet; the dryer’s electrical needs are usually met by a standard 120-volt, 3-prong grounded household outlet, while the heat comes from the gas supply.
- 120V power for the motor, controls, igniter, and sensors
- A grounded outlet (avoid adapters that defeat grounding)
- A dedicated circuit is preferred if the breaker trips, but it is not a “special dryer outlet” like many electric dryers use
A gas dryer setup is more about safe fuel and airflow than a high-voltage receptacle.
- Gas supply connection must be correct for your home (natural gas or LP conversion if applicable)
- Shutoff valve should be accessible
- Proper venting is critical to drying performance and safety
- Keep lint buildup under control to prevent overheating and nuisance shutdowns
| Dryer type | Typical outlet | Typical voltage | Main heat source |
|---|---|---|---|
| Gas dryer (like 11087984110) | Standard grounded household outlet | 120V | Gas burner |
| Electric dryer | Dryer receptacle | 240V | Electric heating element |
Using the correct outlet and a properly grounded connection helps the dryer run the drive motor and ignition system reliably. If the dryer is connected incorrectly, you can see symptoms like no-start, intermittent heat, or blown safety devices such as the thermal fuse WP3390719.
- Confirm the outlet has power (test with a lamp or meter)
- Reset the breaker and check for a tripped GFCI (if used)
- Check airflow: clean lint screen and vent ducting
- If the dryer runs but will not heat, common gas-heat suspects include the dryer igniter 279311 and the dryer gas valve coil kit 279834
- If the start button does nothing, the dryer start switch WP346343 is a common check point
For step-by-step symptom-based help, use our gas dryer wont start troubleshooting video and gas dryer wont heat troubleshooting video.
Last updated: January 2026
How do you reset the PF code on a Kenmore Elite dryer?
On Kenmore model 11087984110, the PF code means a power interruption was detected. To clear it, press Pause/Cancel/Stop twice (or Stop twice, depending on your console) and then restart the cycle.
PF is not a “bad part” code by itself; it is the dryer telling you it lost power during or between cycles.
- Make sure the dryer is plugged in firmly and the outlet is not loose
- Reset the house breaker fully (switch OFF, then ON)
- Avoid using an extension cord or power strip
- If the display comes back but the dryer will not run, check the door is fully closed
- If PF returns often, test a different outlet or have the outlet checked
If PF clears but returns repeatedly, focus on power stability and the start circuit.
| Symptom | Most likely cause | What we recommend |
|---|---|---|
| PF shows after storms/outages | Utility power interruption | Clear PF and run a new cycle |
| PF shows when starting a cycle | Loose plug, weak outlet, breaker issue | Check outlet fit and breaker reset |
| Dryer has power but will not start | Start switch or door switch issue | Inspect the start and door switch operation |
PF itself does not automatically mean you need parts, but if the dryer will not start after clearing PF, these are common checks:
- Dryer start switch WP346343 (if the button does not reliably start the motor)
- Switch W10820036 (if the dryer acts like it is not “ready” to run)
- Dryer motor switch 279827 (if the motor circuit is not engaging)
Clearing PF gets you running again, but repeated PF events can point to a loose electrical connection that can cause intermittent no-start problems and inconsistent drying performance.
Last updated: January 2026
What does CL mean on a Kenmore Elite dryer?
On a Kenmore dryer, CL typically means Control Lock (child lock) is turned on, so the controls will not respond normally. For Kenmore model 11087984110, you can usually clear it by pressing and holding the Control Lock button (or the button labeled for control lock) for about 3 seconds.
Try these steps in order:
- Press and hold the Control Lock button for about 3 seconds.
- If there is no dedicated Control Lock button, press and hold the button that has a lock icon or says Hold 3 sec.
- If the panel is unresponsive, unplug the dryer (or switch off the breaker) for 1 minute, then restore power and try again.
- If CL returns immediately, check for a stuck key on the console (a button that feels jammed or always “pressed”).
When Control Lock is off, you should be able to change cycles and start the dryer normally.
| Symptom | What it usually means | What to do |
|---|---|---|
| CL shows and buttons do nothing | Control Lock is enabled | Hold Control Lock (or lock icon) 3 seconds |
| CL clears but comes back | Button is being held or stuck | Inspect console buttons for sticking |
| No display change at all | Power or control issue | Reset power; then check start/door switch operation |
Control Lock prevents accidental cycle changes, but it can look like the dryer “won’t start.” Clearing CL first helps you avoid replacing parts that are not actually bad.
If the dryer still will not start after CL is cleared, these are common next checks on a gas dryer:
- Confirm the door fully closes and latches; a worn latch can stop starting.
- Check the start switch operation; a failed switch can prevent the motor from running.
- If the motor runs but heat is inconsistent, gas ignition parts can be involved.
Helpful parts for this model include the dryer start switch WP346343 and the strike 279570.
For display or code-related help across Kenmore 110-series electronic control dryers, use our Kenmore 110 series electronic control model dryer error codes reference.
Last updated: January 2026
