Kenmore 10652703100 side-by-side refrigerator Parts

The Kenmore Coldspot 10652703100 side-by-side refrigerator is approximately 66 3/4 in. tall (with hinge) and 33 7/9 in. deep (with handle). For planning a tight install, confirm the exact cabinet clearances and door-swing space in the owner's manual.

Dimensions to use for planning

Use these measurements when checking fit through doorways and into the final opening:

• Height without hinge: 65 7/9 in.
• Height with hinge: 66 3/4 in.
• Depth without handle: 32 1/8 in.
• Depth with handle: 33 7/9 in.

Installation clearances (space you should leave)

Even when the refrigerator “fits,” it still needs breathing room and door-swing clearance.

• Leave about 1/2 in. on each side and at the top for ventilation
• If installed next to a fixed wall, leave at least 2 in. on the hinge side so the door can swing open
• Allow extra space behind the unit if you have an ice maker and water line connections
• Avoid installing near heat sources (oven, radiator)
• Don’t install where temperatures drop below 55°F

Quick reference table

Measurement	Without hinge/handle	With hinge/handle
Height	65 7/9 in.	66 3/4 in.
Depth	32 1/8 in.	33 7/9 in.

Why it matters

Correct sizing prevents delivery surprises, protects the doors from rubbing a wall, and helps the sealed refrigeration system cool efficiently by maintaining proper airflow around the cabinet.

Last updated: February 2026

On the Kenmore 10652703100 side-by-side refrigerator, defrost timing is typically handled by the adaptive defrost control (ADC) in the control housing area rather than a separate, easy-to-spot mechanical timer. We use the wiring diagram and control section in the owner's manual to pinpoint the exact location for your configuration.

Where to look first (common locations)

On Kenmore 106-series side-by-side models, the defrost control is most often found in one of these areas:

• Inside the fresh food section control console (temperature control housing at the top)
• Behind the toe grille or lower front kickplate area (less common on ADC designs)
• In the rear machine compartment near the compressor area (rare for a “timer”, more common for control boards)

How to confirm whether you have a timer or an ADC

A true defrost timer is usually a small box with a dial/advance shaft you can turn with a flat-blade screwdriver. An ADC is a small electronic board with wiring connectors and no dial.

• If you see a dial you can manually advance, you have a mechanical defrost timer
• If there is no dial and you see a small circuit board, you have an ADC
• If the refrigerator “regularly runs an automatic defrost cycle” and you hear water dripping/sizzling during defrost, that is normal operation (not a symptom by itself)

Quick access checklist (safe, practical steps)

• Unplug the refrigerator before removing any control covers
• Empty the top shelf area if you are working in the control console
• Remove the light shield/control cover screws (if equipped)
• Take a photo of wire connector positions before disconnecting anything
• Reinstall covers fully to avoid airflow issues and temperature problems

Why it matters

Finding the correct defrost control helps you troubleshoot frost buildup, warm temperatures, or long run times without replacing the wrong part. Many “no cool” complaints are airflow-related (blocked vents) or normal defrost behavior, not a failed timer.

What you see	What it usually means	Next step
Dial/advance shaft	Mechanical defrost timer	Locate timer body and test/advance
Small circuit board, no dial	Adaptive defrost control	Identify board location and test per manual
Heavy frost on freezer back wall	Defrost system issue likely	Check heater/bi-metal circuit

If you’re diagnosing a defrost failure (heavy frost, poor airflow), the defrost safety thermostat is a common checkpoint; for this model, see the refrigerator defrost bi-metal WPW10225581.

Last updated: February 2026

On your Kenmore side-by-side refrigerator model 10652703100, the model number is printed on the model and serial number label located on the inside wall of the fresh food (refrigerator) compartment. Open the refrigerator door and look along the interior side wall for the label.

Quick ways to find the label

• Check the inside wall near the crisper drawers (common spot on side-by-side units)
• Look on the left or right interior liner wall, not on removable shelves or bins
• Use a flashlight; the label can be low and partially shaded
• Wipe the area with a damp cloth if the print is hard to read
• Write down both the model number and serial number for parts lookup and service records

What you should record (and why)

The label typically includes both identifiers. We recommend recording them exactly as shown.

Item on label	What it’s used for	Example for this unit
Model number	Matching parts and diagrams to your exact refrigerator	10652703100
Serial number	Dating/production info and service history	Varies by unit

Why it matters

Kenmore model families can look similar, but parts like a water filter, water inlet valve, or door gasket can vary by model and production run. Using the exact model number from the label helps ensure you get the right replacement part the first time.

Helpful reference

For additional details on recording your model and serial information, see the owner's manual.

Last updated: February 2026