Kenmore 11020022012 washer Parts

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 11020022012 top-load washer, real-world life depends most on load size, how often it runs, and whether wear items (like hoses and lid locks) are maintained per the 11020022012 installation guide.

What affects lifespan the most

These are the biggest factors we see that shorten or extend washer life:

• Overloading (stresses the drive system, suspension, and tub)
• Unbalanced loads (increases vibration and wear)
• Hard water and detergent buildup (can cause odors and performance issues)
• Leaks left unaddressed (can damage bearings, motor components, and wiring)
• Preventive replacement of wear items (especially hoses and lid/lock parts)

Maintenance that helps your 11020022012 last longer

The installation instructions for this model include a key maintenance point: inlet hoses should be replaced on a schedule and inspected for damage.

• Replace inlet hoses about every 5 years
• Periodically inspect hoses for bulges, kinks, cuts, wear, or leaks
• Keep the washer level to reduce vibration and “washer walk”
• Use the correct detergent amount to reduce residue
• Address small issues early (slow drain, unusual noise, intermittent lid locking)

Quick “wear item” guide

Item	Typical role	Why it matters
Fill hoses	Bring hot/cold water into the washer	Old hoses are a common source of leaks
Lid lock	Confirms lid is closed for safe operation	A failing lock can stop cycles or prevent spinning
Drain pump	Pumps water out during drain/spin	Weak draining can strain the system and leave water behind

If you’re proactively replacing hoses, a compatible option is the washer fill hose set 8212545RP.

Why it matters

Knowing the typical 10 to 15 year lifespan helps you decide whether a repair is worth it. If your 11020022012 is within that range, replacing common wear parts is often a cost-effective way to keep it running reliably.

Last updated: January 2026

Yes. Kenmore washer model 11020022012 uses a drain pump clean-out filter that can catch lint and small items before they reach the pump. Cleaning it can help with slow draining, standing water, and drain-related noises; see the 11020022012 installation guide for safety and access basics.

Where the “filter” is on this model

On many Kenmore top-load washers, the filter is part of the drain system rather than a removable lint screen at the top.

• It’s typically integrated with the drain pump area.
• It may be accessed from the bottom or lower cabinet area (not from inside the tub).
• Expect some water to spill when you open it.
• If your washer is not draining, check the filter before replacing parts.

How to check and clean it (safe, practical steps)

1. Unplug the washer.
2. Turn off both water faucets.
3. Bail out water from the tub if needed.
4. Place towels and a shallow pan under the pump area.
5. Open and clean the washer drain pump clean-out filter WPW10215093.
6. Reinstall the filter securely and run a quick rinse/drain to confirm normal draining.

Quick comparison: lint screen vs pump filter

Item	What it does	Common location
Lint screen	Catches lint during wash	Under agitator or tub rim (varies)
Pump clean-out filter	Catches debris before the pump	At/near drain pump (common on many models)

Why it matters

A clogged pump filter can restrict water flow, which can lead to longer cycle times, poor spin performance, or pump strain. Keeping the filter clean is one of the simplest ways to prevent “won’t drain” problems.

Last updated: January 2026

On Kenmore top-load washer model 11020022012, an F21 code points to a long-drain problem. Clear it by canceling the cycle, resetting power, and correcting the drain restriction (most often the pump clean-out filter, drain pump, or drain hose). Use the 11020022012 installation guide to confirm proper drain-hose setup.

Steps to clear the code on model 11020022012

• Press Pause/Cancel (or Stop) to end the cycle.
• Unplug the washer for 1 minute, then plug it back in.
• If water is standing in the tub, select Drain/Spin.
• If it will not drain, remove water safely (wet/dry vac or gravity drain into a shallow pan).
• Check and clean the pump filter: washer drain pump clean-out filter WPW10215093.

What to check first (most common causes)

1. Drain hose installation: Standpipe height and how far the hose is inserted can cause slow drain or siphoning.
2. Pump filter blockage: Coins, lint, and small items restrict flow.
3. Drain pump issue: A jammed impeller or weak pump can cause slow draining.
4. Hose restrictions: Kinks, pinches, or internal buildup in the drain path.

Parts that commonly solve an F21 long-drain issue

Symptom	What to inspect	Model-compatible part
Slow drain, debris found	Pump filter	WPW10215093
Hose kinked, split, or soft	Drain hose	W11244231
Pump noisy, hums, or drains poorly	Drain pump assembly	WPW10276397

Why it matters

A long-drain condition can stop the cycle and prevent a full spin, leaving clothes wet. Fixing the restriction helps the washer drain at the correct rate and protects the pump and drive system.

Last updated: January 2026

Kenmore model 11020022012 is a top-load washer, so front-load reset steps do not match this machine. For this model, the most reliable reset is a basic power reset: stop the cycle, remove power briefly, then restart a cycle to see if the control clears.

Reset steps for Kenmore 11020022012 (top-load)

• Press Pause/Cancel (or Power) to stop the current cycle.
• Unplug the washer or switch the breaker off.
• Wait 2 to 5 minutes.
• Restore power.
• Lift and close the lid once.
• Select a short cycle such as Rinse/Spin, then press Start.

For power and setup items that can prevent a restart (grounded outlet, dedicated circuit, correct drain setup), follow the 11020022012 installation instructions.

If it still will not start after a reset

These checks apply to Kenmore top-load washers like model 11020022012:

• Confirm the outlet has power (test with a lamp).
• Make sure the lid closes fully and the strike lines up with the lock.
• Turn on both hot and cold water faucets.
• Check inlet hoses for kinks; clean the inlet screen filters if fill is slow.
• Verify the drain hose is installed correctly (not shoved too far down the standpipe).

Parts that commonly affect “won’t start” or “stops mid-cycle”

If the reset helps only temporarily, a failing component may be the real cause.

Symptom	What to check	Model-compatible example part
Won’t start, lid won’t lock	Lid lock and strike alignment	Washer lid lock assembly W10404050
Stops with water in tub	Drain pump and drain path	Washer drain pump assembly WPW10276397
Won’t fill or fills wrong	Water inlet valve	Washer valve WPW10432353

Why it matters

A power reset can clear a temporary control glitch. If the washer cannot lock the lid, fill, or drain correctly, it may stop again until the underlying issue (installation, wiring, or a failed part) is corrected.

Last updated: January 2026