Kenmore 11082870820 washer Parts

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore model 11082870820, lifespan depends most on load size, how often you run it, and whether wear items (like the drive coupling, pump, and suspension parts) are replaced when symptoms first show up.

Most washers land in the same general range, but usage changes the outcome.

• Light use (1 to 3 loads/week): often closer to 15 years
• Average use (4 to 7 loads/week): typically 10 to 15 years
• Heavy use (8+ loads/week): often closer to 8 to 12 years

These habits reduce strain on the motor, clutch, and gear case.

• Keep loads balanced; mix large and small items
• Avoid overloading; it accelerates clutch and coupling wear
• Use the right amount of detergent to reduce residue and drag
• Check fill and drain hoses for kinks and slow draining
• Level the washer to reduce vibration and suspension wear
• Address new noises early (grinding, squealing, banging)

Washer failures are often caused by a few high-wear components. Replacing a relatively small part early (for example, a pump or agitator drive part) helps protect bigger, higher-cost assemblies like the gear case and drive basket.

Last updated: February 2026

Kenmore washer model numbers use a consistent pattern: the first 3 digits identify who built the washer for Kenmore, the next group identifies the base design, and the final digits show the specific version. Your model number 11082870820 follows that same format.

Most Kenmore washer model numbers break down like this:

• Prefix (first 3 digits): manufacturer identifier (who produced the washer for Kenmore)
• Middle digits: base model or platform (the core design family)
• Ending digits: variation details (features, color, revision, or production run)

We use the full model number to match parts that fit your exact washer configuration. Even small suffix changes can affect items like the lid switch, water inlet valve, or drive system.

Common part categories that can vary by model version include:

• Agitation and drive parts (agitator components, clutch, coupling)
• Drain components (pump and hoses)
• Fill components (water inlet valve)
• Safety and control parts (lid switch)
• Tub and basket hardware (drive block, spanner nut, gasket)

Here are a few common replacement parts we list for Kenmore 11082870820 (examples of why the exact model matters):

Reading the model number correctly prevents ordering the wrong Kenmore washer parts and saves time on repairs. Using the full 11082870820 model number is the most reliable way to match the correct fit.

Last updated: February 2026

The exact cubic-foot capacity for Kenmore washer model 11082870820 is not listed in the model details we have here; most Kenmore 110-series top-load, direct-drive washers of this style typically fall in the about 3.0 to 3.5 cu. ft. range, depending on the tub and basket used.

If you need a working number for load sizing, you can estimate tub volume by measuring the inside of the wash basket.

• Unplug the washer for safety.
• Measure the inside diameter of the basket (in inches).
• Measure the usable depth from the bottom to the highest fill line you normally use (in inches).
• Use the formula below.
• Convert cubic inches to cubic feet.

Formula

• Cubic inches = 3.1416 × (diameter ÷ 2)² × depth
• Cubic feet = cubic inches ÷ 1728

For Kenmore 110-series, agitator-equipped top-load washers, capacity usually lands in a narrow band. Use this as a practical guide for detergent dosing and load size.

Capacity affects cleaning and wear. Overloading reduces agitation and rinsing, increases out-of-balance spinning, and can accelerate wear on drive components like the coupling 285753A and clutch 285785.

Use these practical rules for a Kenmore agitator top-load washer:

• Load loosely to the top of the basket; do not pack items down.
• Keep a palm-width gap at the top so clothes can circulate.
• Wash bulky items in pairs (two towels, two jeans) to balance.
• If the washer struggles to spin or bangs, reduce the load size.
• If draining is slow, check for pump or hose restrictions; the water pump WP3363394 is a common service part.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the fix restores reliable washing and spinning for less than the cost of replacing the machine. For Kenmore model 11082870820, many common failures are repairable with standard mechanical parts, so a targeted repair often delivers years of additional service.

We use three practical checks before buying parts:

• Symptom severity: No-spin, no-agitate, or no-drain problems are often straightforward; cabinet rust, severe leaks, or repeated electrical failures are not.
• Repair cost vs. replacement: If parts plus labor stay well below a comparable new washer, repair wins.
• Overall condition: If the tub, basket, and cabinet are solid and the washer has not been flooding, repairs tend to hold.

These are frequent wear items on many Kenmore top-load designs; they are typically cost-effective compared with replacement:

• Agitation issues (worn dogs or cam): agitator dog 80040, agitator cam 285748
• No-agitate or loud grinding at start (drive coupling): coupling 285753A
• Won’t drain or leaves water in tub (pump): water pump WP3363394
• Spin problems or burning smell (clutch): clutch 285785

A repair-first approach is often the fastest way to get dependable wash performance back, especially when the failure is a single wear part (coupling, pump, clutch, or agitator components). Replacing the right part also prevents secondary damage, such as overheating the drive motor or stressing the gear case.

Last updated: February 2026