Amana NDG7800AWW dryer Parts

Most Amana dryers, including the Amana NDG7800AWW, last 10 to 15 years with normal household use. Consistent airflow maintenance (lint screen and venting) and fixing small wear items early are what most often push a dryer toward the high end of that range; see the NDG7800AWW owner's manual for routine use and care guidance.

A dryer’s life is mostly determined by heat stress, airflow restriction, and mechanical wear.

• Vent restriction (long runs, crushed flex duct, lint buildup) overheats components
• Overloading strains the drive motor and drum support system
• Skipping lint screen cleaning reduces airflow and drying performance
• Worn drum support parts increase friction and noise
• Gas ignition wear can cause intermittent heat and longer cycles

These symptoms often show up in the last few years of service and are commonly repairable.

When a gas dryer runs but won’t heat reliably, these model-compatible parts are common fixes:

• Dryer valve coil kit 279834 (gas valve coils for ignition)
• Flame sensor WP338906 (verifies burner flame/heat)
• Igniter WP37001308 (lights the gas)

For noise and drum support wear, these are common wear items:

• Dryer drum support roller WP37001042
• Idler assembly WP37001144

A dryer that is restricted by lint or venting often dries slower, runs hotter, and wears out key parts sooner. Keeping airflow strong is the simplest way to protect the motor, thermostats, and gas ignition components.

• Clean the lint screen every load
• Inspect and clean the vent path periodically (dryer outlet to exterior hood)
• Avoid overloading; dry bulky items in smaller loads
• Stop using the dryer if you smell gas; follow the safety steps in the NDG7800AWW installation guide
• Order model-specific replacement parts from the parts list for NDG7800AWW, or search by model on Sears PartsDirect

Last updated: February 2026

Common failures on the Amana NDG7800AWW dryer are heat-related parts (igniter, flame sensor, gas valve coils, thermostats), airflow parts (lint screen, blower wheel), and drum support parts (rollers, idler). These issues typically show up as no heat, long dry times, noise, or a drum that will not turn.

• No heat (gas dryer): igniter, flame sensor, gas valve coils, high-limit thermostat
• Takes too long to dry: clogged lint screen, restricted venting, blower wheel issues
• Squealing, thumping, or rumbling: drum support rollers, idler assembly
• Drum will not tumble: drive motor, idler assembly (belt tension system)
• Dryer stops mid-cycle or overheats: operating thermostat, limit thermostat

These are common wear or heat-cycle parts for this model:

We follow these basics because they directly affect heating performance and safety:

• Disconnect electrical power before servicing.
• Keep the lint screen clean before or after each load.
• Use rigid or semi-rigid metal ducting; avoid plastic or thin foil duct.
• Exhaust to the outside using the shortest practical route.
• Never use a gas line for grounding.

For the exact safety, grounding, and venting requirements for NDG7800AWW, use the NDG7800AWW installation guide and the NDG7800AWW owner's manual.

Most “bad dryer” complaints are really heat plus airflow problems. A restricted vent or dirty lint screen can cause long dry times, overheating, and repeated thermostat or limit thermostat failures. Fixing airflow first prevents unnecessary part replacement.

We recommend matching parts by the full model number (NDG7800AWW) and the symptom you are seeing. You can order the parts listed for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

Replacing drum bearings (or the drum support parts that act like bearings) on an Amana NDG7800AWW dryer typically costs $200 to $600 total (parts plus labor). If the job also needs a belt, idler, or drum rollers, the total usually lands toward the higher end; see the NDG7800AWW installation guide for access and safety basics.

Most “drum bearing” quotes include some combination of drum support components and the labor to disassemble the cabinet and drum.

• Service call and diagnosis
• Labor to remove the front panel, drum, and supports
• Replacement support parts (roller(s), glides, felt seal, retaining hardware)
• Reassembly, airflow check, and test run

On the NDG7800AWW, rumbling, thumping, or squealing is often tied to drum support wear. These parts are commonly involved:

• Dryer drum support roller WP37001042 (worn roller can rumble or thump)
• Dryer drum glide bracket WP37001036 (worn glides can squeal and scrape)
• Felt complete pad WP500121 (worn felt can cause scraping and poor drum support)

Worn drum support parts increase friction and drag. That can lead to longer dry times, overheating, and extra strain on the drive motor and belt system. Fixing the support issue early usually keeps the repair smaller and less expensive.

• Clean the lint screen and confirm strong airflow; restricted venting can overheat and accelerate wear.
• If the dryer is already apart, replace all worn support items at the same time to avoid paying labor twice.
• Use the parts list for NDG7800AWW first, then search by model on Sears PartsDirect if you need additional related items.

Last updated: February 2026

On an Amana NDG7800AWW dryer, a blown thermal fuse reads open (OL/infinite) on a multimeter; a good fuse reads 0 to 1 ohm (or beeps on continuity). Unplug the dryer before testing, and fix the overheating cause (usually restricted venting) before replacing the fuse.

• Disconnect power; for gas models, also shut off the gas supply.
• Access the fuse (commonly on the blower housing or exhaust duct area).
• Remove the wires from the fuse terminals (pull on the connector, not the wire).
• Set the meter to ohms or continuity.
• Touch one probe to each terminal.
• Read the result:
  • 0 to 1 ohm or steady beep: fuse is good
  • OL/infinite/no beep: fuse is blown

Overheating is usually caused by poor airflow. The NDG7800AWW manual emphasizes keeping the lint filter and exhaust duct clean and inspecting the exhaust system annually.

• Clean the lint screen every load.
• Check the vent hose for kinks, crushing, or heavy lint buildup.
• Confirm the outside exhaust hood flap opens and closes freely.
• Use rigid 4-inch metal duct when possible; keep runs short with fewer elbows.

After airflow checks, these are common heat-related suspects:

• Flame sensor WP338906
• Igniter WP37001308
• Dryer valve coil kit 279834

If you replace a blown thermal fuse without correcting vent restriction, the new fuse often blows again and drying performance stays poor.

For model-specific safety and access guidance, use the NDG7800AWW owner's manual. You can order parts from the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026