Owner’s manual
Error Codes
How big is the Kenmore Coldspot refrigerator?
For Kenmore model 10658033800 (Coldspot side-by-side), the manual calls for a 36 in minimum cabinet cutout width for installation; overall refrigerator height and depth vary by configuration, so we use the model’s spec section in the 10658033800 owner's manual to confirm exact exterior dimensions.
The installation requirements in the manual specify:
- Minimum cabinet opening width: 36 in (91.44 cm)
- Recommended clearance: 1/2 in on each side and at the top
- Wall clearance for door swing: 2 in minimum on each side when next to a fixed wall
- Extra rear space: needed if you have an ice maker and water line connection
Most 36-inch Kenmore side-by-side refrigerators are approximately:
- Width: 35 1/2 to 36 in
- Height: 66 to 71 in
- Depth: 30 to 34 in (not including handles varies by model)
| Measurement | What it means | What to check |
|---|---|---|
| Width | Fits between cabinets | Cabinet opening and trim clearance |
| Height | Fits under soffits/cabinets | Floor to overhead cabinet height |
| Depth | Sticks out past counters | Depth with handles and door swing |
Use a tape measure and record these three numbers:
- Width: widest point (often door edges)
- Height: floor to top hinge cover area
- Depth: back to front of handles (and note “without handles” if needed)
Correct sizing prevents door-swing issues, blocked crisper drawer removal, and poor airflow. The manual’s clearance guidance also helps the condenser and evaporator fan system cool efficiently.
Last updated: January 2026
How to replace water filter in Kenmore side by side refrigerator?
For Kenmore side-by-side refrigerator model 10658033800, the water filter is in the base grille below the freezer door. Press the eject button, pull the filter straight out, move the cap to the new filter, then push the new filter in until it locks and flush the system.
- Locate the filter in the base grille below the freezer compartment door (you do not need to remove the grille).
- Press the eject button and pull straight out on the filter cap to remove the filter.
- Turn the filter cap counterclockwise until it stops, then remove the cap.
- Prep the new filter cartridge:
- Remove packaging.
- Remove the protective cover from the O-rings.
- Install the cap on the new filter:
- Align the ridge on the cap with the arrow on the filter.
- Turn the cap clockwise until it snaps into place.
- Push the new filter into the opening until fully engaged (the eject button pops back out).
- Pull gently on the cap to confirm the filter is seated.
For diagrams and model-specific notes, follow the 10658033800 owner's manual.
We recommend flushing to clear air and carbon fines:
- Hold the dispenser lever for 5 seconds, then release for 5 seconds.
- Repeat until water begins to flow.
- Then continue the 5-seconds-on, 5-seconds-off cycle for 2 more minutes.
- Expect some spurting while air clears.
- Cap comes off while removing the filter: avoid twisting; reinstall the cap and pull the filter straight out.
- Water drips during removal: keep a towel handy; some spilling is normal.
- Low water flow after replacement:
- Flush longer.
- If you use reverse osmosis, the refrigerator filter can reduce pressure further; remove the filter temporarily to test.
- Check household water pressure and any sediment filters in the RO system.
| Symptom | Most likely area | Example part for this model |
|---|---|---|
| No water to dispenser/ice maker | Water supply valve not opening | Refrigerator inlet valve W10408179 |
| Filter will not seat or leaks at cap | Filter cap/O-ring interface | Refrigerator water filter cap (black) WP2260518B |
A properly installed and flushed water filter helps protect the water system, improves taste and odor, and prevents air pockets that can cause dispenser sputtering or ice maker fill problems.
Last updated: January 2026
Why is my Kenmore side by side ice maker not working?
If the ice maker in your Kenmore 10658033800 side-by-side refrigerator isn’t making ice, the most common causes are the ice maker being switched OFF, the storage bin not seated (which stops ice production), or a water supply issue. Start by confirming the ice maker On/Off switch is ON and allow time for production.
- Make sure the ice maker On/Off switch is in the ON (left) position.
- Reseat the ice storage bin fully; removing the bin stops ice production.
- Keep the freezer door closed; the dispensing system will not operate with the door open.
- Allow time: 24 hours for the first batch, up to 3 days to fill the bin.
- Discard the first three batches after restoring operation (helps flush impurities).
For the exact On/Off switch location and storage bin removal steps, use the 10658033800 owner's manual.
If the ice maker is ON and the bin is seated but there is still no ice, focus on water delivery.
- Confirm the household water supply valve is fully open.
- Check for a kinked or pinched water line behind the refrigerator.
- Replace the water filter if flow is weak or the filter is overdue.
- If you hear buzzing (valve energizing) but no water enters, the inlet valve may be failing.
If you suspect the valve is not opening consistently, the model-matched replacement is the refrigerator inlet valve W10408179.
| Situation | What you should see |
|---|---|
| Ice maker just turned ON | First cubes within about 24 hours |
| Bin was removed or not seated | Ice production resumes once bin is reinstalled |
| Water system was serviced | Discard first 3 batches of ice |
An ice maker that is OFF, blocked by a mis-seated bin, or starved for water can look “dead” even though the ice maker itself is fine. These checks prevent unnecessary parts replacement and get ice production back faster.
Last updated: January 2026
