Frigidaire FEB24S2ABC electric oven Parts

Frigidaire wall ovens, including model FEB24S2ABC, are a solid choice when they are installed correctly and maintained; they typically deliver consistent baking and broiling performance, straightforward controls, and widely available replacement parts when normal wear items eventually fail.

What “good” looks like for a wall oven

A wall oven is doing its job well when it reliably holds temperature, heats evenly, and the door and controls operate smoothly.

• Preheats in a reasonable time and reaches set temperature
• Bakes evenly without large hot or cold spots
• Broils consistently without cycling off too early
• Door seals well and closes squarely
• Controls respond normally and do not reset or flicker

Installation quality matters more than most people expect

A lot of “bad oven” complaints come from installation issues, not the oven itself. For this Frigidaire wall oven, the installation guide calls out key requirements such as proper grounding and using a dedicated, properly protected circuit.

• Confirm the oven is installed and grounded properly
• Use an individual, properly grounded branch circuit (as specified for the appliance)
• Make sure the cabinet cutout and support surface are level side-to-side and front-to-rear
• Follow the minimum clearance guidance for the door-open position and surrounding cabinetry

For the exact cutout dimensions and electrical requirements that apply to your setup, use the installation guide.

Common “good oven” fixes when performance drops

Even a good wall oven can act up when a few common parts wear out. These are typical, practical repairs for heating and temperature complaints.

Symptom	Most common cause	What we check first
Oven temperature is off	Temperature sensor drifting	Sensor resistance and wiring connections
Oven will not heat	Failed bake element	Visual damage, continuity test
Light does not work	Bulb or socket issue	Bulb first, then socket and wiring

Model-matched parts that often help include the Frigidaire range oven temperature sensor 316217002, Frigidaire range bake element 318255101, and range oven light bulb 316538904.

Why it matters

A wall oven is a built-in appliance; when it is installed to spec and kept in good repair, you get more consistent cooking results and fewer nuisance issues like uneven baking, long preheat times, or control problems.

Last updated: February 2026

If your Frigidaire FEB24S2ABC wall oven will not turn on, the most common causes are a tripped breaker or blown fuse on the dedicated circuit, a loose or burned power connection at the terminal block, or a failed control component such as the control board. Use the wiring and power requirements in the installation guide to confirm the oven is on the correct, properly grounded branch circuit.

Quick checks we recommend first (power and safety)

• Reset the oven’s dedicated circuit breaker fully OFF, then back ON.
• If your home uses fuses, replace the fuse with the correct rating for the circuit (do not oversize).
• Confirm the oven is on an individual, properly grounded branch circuit (not shared with other large loads).
• If the display is blank, check for a loose, overheated, or damaged connection where the house wiring lands.
• If you smell burning or see melted wiring, keep power OFF and have the connection repaired before using the oven.

Likely causes and what each one looks like

What you see	Most likely issue	What to do next
No lights, no display, no beeps	No power from breaker/fuse, or failed connection	Verify breaker/fuse and inspect the power connection area
Power is present but controls do not respond	Control board or control panel issue	Check for stuck keys; if none, suspect the control board
Oven turns on sometimes, then shuts off	Loose connection or failing control	Inspect wiring connections; then evaluate control board

Parts that commonly fix a “won’t turn on” condition

If power to the unit is correct and stable, these model-compatible parts are common fixes:

• Terminal block 5304409888 (burned or loose power cord/house wiring connection point)
• Wall oven control board 318185330 (no response, erratic operation, dead display with confirmed power)
• Wall oven control board 318185329 (alternate control board option listed for this model)

Why it matters

A wall oven that will not power up is often a supply issue, not an oven cavity issue. Confirming correct voltage, grounding, and tight, undamaged line connections prevents repeat failures and protects sensitive electronics like the control board.

Last updated: February 2026

A Frigidaire electric wall oven like model FEB24S2ABC typically lasts 10 to 15 years with normal household use. With consistent cleaning, proper airflow, and timely replacement of wear items (like heating elements and sensors), many ovens run 15 to 20 years.

Typical lifespan and what affects it

Most wall ovens reach end of life due to heat-related wear on electrical parts, not because the cabinet wears out.

• Heavy use (daily baking, frequent broiling) shortens lifespan
• Self-clean cycles run extremely hot and add stress to wiring and controls
• Power surges and loose connections can damage the control board
• Poor cleaning habits can cause corrosion, smoke, and overheating
• Replacing common failure parts early often extends overall oven life

Common parts that limit oven life (and what they do)

These are some of the most common “life-limiting” components for an electric wall oven.

Part	What you’ll notice when it’s failing	Example part for FEB24S2ABC
Bake element	Slow preheat, uneven baking, no heat in Bake	Frigidaire range bake element 318255101
Temperature sensor	Temperature swings, overbakes, error beeps on some models	Frigidaire range oven temperature sensor 316217002
Control board	Dead display, random shutoffs, buttons not responding	Wall oven control board 318185330
Oven light system	Light out, flickering, lens damage from heat	Range oven light bulb 316538904

Maintenance that extends life

We recommend these habits because they reduce heat stress and prevent avoidable damage.

• Wipe heavy spillovers promptly (less smoke and odor during cleaning)
• Keep vents clear so heat can escape normally
• Avoid lining the oven bottom or walls with aluminum foil (it can damage heat distribution)
• Use self-clean only when needed; let the oven cool fully afterward
• If baking temps seem off, test with an oven thermometer and then follow the calibration steps in the owner's manual

Why it matters

Knowing the typical 10 to 15 year lifespan helps you decide whether to repair or replace. If your FEB24S2ABC is heating poorly but the oven is otherwise in good shape, replacing a bake element, sensor, or control component is often the most cost-effective way to get reliable performance back.

Last updated: February 2026

To reset your Frigidaire FEB24S2ABC wall oven, we recommend doing a power reset by turning the oven’s circuit breaker OFF, waiting 3 to 5 minutes, then turning it back ON. This clears many control glitches and can stop nuisance error codes after a power surge.

Reset steps (safe, reliable)

• Turn the wall oven breaker OFF (do not just turn the oven controls off).
• Wait 3 to 5 minutes so the electronic control fully discharges.
• Turn the breaker back ON.
• Set the clock and try a simple Bake cycle.
• If the display shows an error again, write down the exact code before resetting a second time.

If an error code comes back after the reset

A reset helps with temporary faults. If the same code returns quickly, the issue is usually a failed sensor circuit, wiring problem, or a control problem.

What you see	What it usually points to	Common next step
Oven heats poorly or temperature swings	Temperature sensing problem	Check/replace the Frigidaire range oven temperature sensor 316217002
Random beeping, stuck keys, odd display behavior	Control or keypad/overlay issue	Inspect the control panel; replace the overlay or control if needed
Oven will not heat at all	Heating circuit problem	Inspect wiring and the bake element for damage

Parts that commonly relate to “won’t reset” symptoms

If the oven won’t recover after a proper power reset, these model-compatible parts are often involved:

• Wall oven control board 318185330 (when the control logic is failing)
• Frigidaire range oven temperature sensor 316217002 (when the oven misreads temperature)
• Wall oven electronic oven control overlay 316220729 (when keys are unresponsive or stuck)

Why it matters

A proper reset restores normal operation after a brief power interruption, but repeated error codes usually mean the oven is protecting you from overheating or incorrect temperature control. Addressing the underlying part issue helps prevent poor baking results and repeat shutdowns.

For model-specific control features and normal operation checks, follow the owner's manual.

Last updated: February 2026

Yes. Looking up parts by model number is the most accurate way to get compatible replacement parts for your Frigidaire wall oven; for this model, use FEB24S2ABC and match parts to the oven’s serial plate information shown when the door is open.

Where to find the model number on FEB24S2ABC

On this Frigidaire wall oven, the serial plate is located along the side of the oven door when the door is open. We recommend copying the model number and serial number exactly before you search or order.

• Open the oven door fully and look along the side trim or front frame area
• Write down the model number (FEB24S2ABC) and serial number
• Keep the information with your purchase date for future reference
• Use the model number first, then confirm the part matches your exact configuration

How to use the model number to choose the right part

Searching by model number narrows results to parts that fit your specific wall oven design (controls, wiring, heating circuit, and trim). After you find a part, confirm it matches the symptom you are fixing.

Common examples for FEB24S2ABC include:

• If the oven light is out: check the range oven light bulb 316538904 and the range oven light socket 316116400
• If baking temperatures seem off: check the Frigidaire range oven temperature sensor 316217002
• If the oven will not heat properly: the bake circuit may involve the Frigidaire range bake element 318255101

Quick part matching checklist (before you order)

Use this checklist to avoid ordering the wrong wall oven part.

• Confirm the appliance model is FEB24S2ABC (not just “FEB24”)
• Match the part by function (light, sensor, control, element)
• Verify the part ID and description align with your repair
• Compare your existing part’s markings when accessible (after power is off)
• Use the diagrams and part list for your model to confirm placement

Common “model number” vs “part number” comparison

What it is	Example	What it’s used for
Model number	FEB24S2ABC	Finds the correct parts list for your exact oven
Part number	5303013071	Manufacturer identifier for a specific replacement part
Part ID	316538904	Sears PartsDirect identifier for the part listing

Why it matters

Wall ovens often share similar-looking components across different models, but wiring, mounting, and control compatibility can vary. Using FEB24S2ABC first helps ensure the replacement part fits and functions correctly.

For diagrams, specifications, and model identification details, use the owner's manual and the installation guide.

Last updated: February 2026