Kenmore 11028332700 washer Parts

Your Kenmore washer model number is on the model and serial number label; for Kenmore model 11028332700, the manual specifies this label is located under the washer lid. Use that full model number when ordering parts so the fit and electrical connections match your exact washer.

Where to look on Kenmore 11028332700

Check these common label locations in this order:

• Under the lid on the top opening (most common for this style)
• Along the lid opening rim (top edge of the cabinet)
• On the rear panel near the power cord entry
• Inside the control console area (less common)

Use the steps and diagrams in the 11028332700 owner's manual to confirm the label location and record the model and serial number.

What the model number looks like (and why it matters)

Kenmore washer model numbers often start with 110 and are typically 11 digits. Entering the full number helps us match the correct Kenmore washer parts list, including items like the lid switch, drain pump, and drive system.

Quick ID checklist

• Write the model number exactly as shown (no spaces)
• Record the serial number too (helps with production variations)
• Match the model number on the label to the one you search for: 11028332700

Common mix-ups to avoid

What you find	What it is	Use it for parts?
Model number (example: 11028332700)	Identifies the washer design	Yes
Serial number	Production code/date info	Sometimes helpful
Part number (example: 3366877)	Identifies a specific part	Only when replacing that part

Why it matters

Using the exact model number prevents ordering the wrong version of a part (for example, a lid switch assembly or drain pump that mounts differently). It also helps when following troubleshooting steps and diagrams.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11028332700, staying within proper installation requirements and avoiding chronic overloading helps you reach the longer end of that range; see the 11028332700 owner's manual for care guidance.

What affects lifespan the most

• Load size and balance: loads should move freely and stay balanced during washing.
• Water quality and pressure: consistent supply helps valves and fill performance.
• Installation conditions: a level, sturdy floor reduces vibration and wear.
• Temperature exposure: avoid storing or operating at or below 32°F (0°C).
• Wear parts over time: drive and agitation components gradually wear with use.

Quick maintenance habits that extend life

We recommend these simple habits for top-load Kenmore washers like 11028332700:

• Do not overload; keep bulky loads evenly distributed
• Use the correct detergent amount and avoid excess suds
• Periodically inspect fill hoses for bulges, cracking, or leaks
• Keep the lid area and tub clean and dry between loads
• Address small issues early (new noises, slow drain, weak agitation)

Common wear items and what symptoms look like

Symptom	Likely area	Example part for this model
Agitator moves poorly or “slips”	Agitator drive	Agitator dog 80040
Washer will not drain or drains slowly	Drain pump, clogs	Washer drain pump WP3363394
Washer will not spin when lid is open or lid sensing fails	Lid switch	Washer lid switch assembly WP8318084

Why it matters

A washer that is overloaded, out of level, or run in freezing conditions wears out faster because the motor, clutch, gearcase, suspension, and drain system work harder than designed. Following the setup specs in the 11028332700 installation guide helps prevent vibration, leaks, and premature part failure.

Last updated: February 2026

For Kenmore washer model 11028332700, the most commonly replaced parts are the ones that affect draining, spinning, agitation, and lid safety. If your washer will not drain, will not spin, or agitates poorly, start by matching symptoms to the parts list and the troubleshooting steps in the 11028332700 owner's manual.

Commonly replaced parts for this model

These parts are frequent fixes for everyday complaints like no-drain, no-spin, leaks, or weak agitation:

• Washer lid switch assembly WP8318084 (won’t spin or drain if the lid switch is not closing)
• Washer drain pump WP3363394 (won’t drain, slow drain, or grinding noise)
• Coupling 285753A (motor runs but washer won’t agitate or spin)
• Clutch 285785 (weak spin, burning smell, or slow basket engagement)
• Agitator dog 80040 (agitator top “ratchets” or won’t move clothes well)
• Washer water inlet valve WP8578340 (no fill, slow fill, or leaking at the valve)

Quick symptom-to-part guide

Symptom	Most likely part(s) to check	What you’ll notice
Won’t spin	Lid switch, clutch, drive block	Stops before spin or spins weakly
Won’t drain	Drain pump, drain hose	Water left in tub, humming, slow drain
Won’t agitate	Coupling, agitator dogs, agitator cam	Motor runs but little or no agitation
Leaks	Inlet valve, tub gasket, tub seal	Water at back (hoses/valve) or under tub

Why these parts matter

This washer uses mechanical drive components (coupling, clutch, drive block) that wear with load stress over time. Safety and water-handling parts (lid switch, inlet valve, drain pump) also see heavy use every cycle, so they are common service items.

Helpful maintenance tip from the manual

The manual calls out a specific interval for hoses: replace inlet hoses after 5 years to reduce the risk of hose failure. Use the 11028332700 owner's manual to track the inlet hose replacement date.

Last updated: March 2026