GE GSD5940D01SS dishwasher Parts

No. GE dishwashers are not all the same size; most built-in models are designed for a standard 24-inch cabinet opening, but GE also makes compact 18-inch units and some models vary slightly in height and depth. For GE model GSD5940D01SS, measure your cabinet opening and the dishwasher cutout before ordering parts or planning a replacement.

Typical GE dishwasher sizes (what to expect)

Most GE built-in dishwashers fall into these common size groups:

• Standard built-in: about 24 inches wide
• Compact built-in: about 18 inches wide
• Height and depth: can vary by model and installation style (leveling legs, countertop height, toe-kick clearance)

Type	Nominal width	Best for
Standard built-in	24 in.	Most kitchens and full-size loads
Compact built-in	18 in.	Apartments, small kitchens, light loads

How we recommend measuring before you buy

Use a tape measure and confirm the opening, not just the old dishwasher’s outer shell.

• Measure opening width at the front and back
• Measure opening height from floor to underside of countertop
• Measure opening depth to the back wall (watch for plumbing and wiring)
• Check door clearance so the door can open fully without hitting an island or nearby cabinet
• If you are replacing racks or seals, confirm the part is listed for your exact model

Why it matters

Dishwashers can look “standard” but small differences in height, depth, and mounting style affect fit, door alignment, and leak prevention. If you are troubleshooting leaks or poor draining on GSD5940D01SS, correct fit and sealing also help parts like the dishwasher door seal WD08X10057 and dishwasher drain hose WD24X10014 do their job.

Last updated: January 2026

Most GE dishwashers, including model GSD5940D01SS, typically last 10 to 12 years. With consistent cleaning and prompt repair of leaks or draining problems, it’s common to reach 12 to 15 years; heavy daily use can shorten lifespan.

What affects how long a GE dishwasher lasts

• Water quality (hard water speeds up scale buildup)
• Cleaning and maintenance (tub, spray paths, and seals)
• How often it runs (multiple loads daily adds wear)
• Drain performance (standing water strains the pump)
• Door sealing (leaks can damage components and flooring)

Quick maintenance that extends lifespan

• Run a monthly cleaning routine using a dishwasher cleaner (or a manufacturer-approved descaler).
• Keep the door seals clean; wipe the tub lip and gasket area after messy loads.
• Make sure the dishwasher drains fully after each cycle.
• Avoid overloading; blocked spray patterns reduce cleaning and increase re-washing.
• Fix small leaks early; a worn seal is cheaper than a damaged motor.

Common “end-of-life” symptoms and likely areas to check

Symptom	What it often points to	Example part for GSD5940D01SS
Won’t drain or drains slowly	Drain path restriction or drain solenoid issue	Dishwasher drain hose WD24X10014
Leaks at the door	Door seal wear or misalignment	Gasket WD08X10057
Loud grinding or weak wash action	Pump/motor wear or seal failure	Mechanism WD26X10013

Why it matters

A dishwasher near the 10 to 12 year mark can still be a great candidate for repair if the tub is solid and the racks are usable. Replacing a wear item like a door seal or drain hose often restores reliable performance and helps prevent bigger failures.

For troubleshooting help when performance drops, use our GE dishwasher error codes guide.

Last updated: January 2026

Yes. On the GE GSD5940D01SS dishwasher, an FTD (fail to drain) error commonly happens when water cannot leave the tub because the drain path is restricted, such as a clogged hose, blocked air gap/disposal inlet, or debris at the pump area.

What to check first (fast, no parts)

• Cancel the cycle and wait a few minutes; listen for the drain pump running.
• Remove standing water (cup or wet/dry vac) so you can inspect the sump area.
• Check the sink drain/disposal connection for a plug or blockage.
• If you have an air gap, remove the cap and clear any buildup.
• Inspect the drain hose for kinks, crushing, or a high loop that fell down.

Common clog points and the likely fix

Where the clog is	What you may notice	What usually fixes it
Drain hose	Slow drain, water returns to tub	Clear hose, correct routing, replace if collapsed
Pump area / impeller zone	Humming, intermittent draining	Remove debris; check for broken pieces
Disposal or sink tailpiece inlet	Dishwasher drains poorly right after install or disposal replacement	Clear inlet; remove knockout plug
Drain solenoid linkage (if equipped)	Drains sometimes, then stops	Inspect linkage; replace worn components

Parts that can be involved if clearing the clog does not solve it

If the drain path is clear but the dishwasher still throws FTD, we focus on the drain components that move water out.

• Dishwasher drain hose WD24X10014: replace if it is split, soft, or internally restricted.
• Dishwasher drain solenoid kit WD21X10060: helps actuate draining on designs that use a solenoid; a stuck plunger or failed coil can mimic a clog.
• Mechanism WD26X10013: if the pump and motor assembly is weak or jammed, it may not push water out consistently.

Why it matters

An FTD condition leaves dirty water in the tub, can redeposit soil on dishes, and can stop the cycle mid-program. Clearing the restriction quickly also helps prevent pump strain and repeat drain errors.

Related help: GE dishwasher error codes, dishwasher not draining video

Last updated: January 2026

The most common problem we see on GE dishwashers like model GSD5940D01SS is a drain or wash-performance issue caused by buildup or a restriction (food debris in the sump area, a kinked/clogged drain path, or a weak pump). “Won’t start” problems from a door-latch or power issue are also very common.

Most common symptoms and what they usually point to

• Water left in the bottom: drain hose restriction, drain solenoid issue, or a blockage in the drain path
• Not cleaning well: weak circulation, clogged spray path, or pump/motor wear
• Won’t start or stops mid-cycle: door not latching, power supply issue, or control problem
• Leaks at the door: worn door seal or misaligned rack loading
• Bad odor: trapped food debris and grease buildup

Quick checks we recommend first (fast, no parts)

1. Reset power: turn the breaker off for 1 minute, then back on.
2. Confirm the door closes firmly: racks should not interfere with the door.
3. Check the drain path: look for kinks behind the unit and ensure the drain line is routed high (high loop).
4. Run a cleaning cycle: use a dishwasher cleaner and remove visible debris from the bottom area.
5. Listen during wash: a healthy unit has a steady wash “spray” sound; a weak hum can indicate circulation trouble.

Parts that commonly solve these problems on GSD5940D01SS

Symptom	Common fix area	Example part for this model
Not draining	Drain path or drain actuator	Dishwasher drain hose WD24X10014 or dishwasher drain solenoid kit WD21X10060
Poor cleaning	Pump and motor circulation	Mechanism WD26X10013
Door leaking	Door sealing surface	Dishwasher door seal WD08X10057 or dishwasher door seal insert WD08X10015

Why it matters

Drain and circulation problems usually get worse over time; the dishwasher can start leaving grit on dishes, holding dirty water, or developing odors. Catching restrictions early helps protect the pump, motor, and seals.

Helpful DIY resources

• Use GE dishwasher error codes or GE electronic dishwasher error codes if your dishwasher is flashing lights or showing a fault pattern.
• If the unit is holding water, follow dishwasher not draining video for a step-by-step diagnostic flow.

Last updated: January 2026