Kenmore 11078942892 gas dryer Parts

The Kenmore gas dryer model 11078942892 is a 27-inch wide dryer. For the exact overall cabinet dimensions (height and depth) and required clearances for your installation, we recommend confirming the measurements listed in the 11078942892 owner's manual.

What we can confirm for this model

From the documentation for this Kenmore 11078942892 gas dryer:

• Width: 27 inches (model family is labeled “27-inch wide gas dryers”)
• Type: Gas dryer
• Installation: Requires proper venting and leveling for best performance

Typical overall dimensions you can expect

Most 27-inch wide Kenmore (Whirlpool-built) gas dryers are close to the following ranges. Use these for planning space, then verify the exact numbers in the manual.

• Width: ~27 inches
• Height: ~38 to 44 inches (varies by control panel style and feet adjustment)
• Depth: ~27 to 30 inches (can increase with vent connection)

Measurement	What it helps with	Typical range for 27-inch dryers
Width	Fit between cabinets	27 inches
Height	Under-counter or shelf clearance	38 to 44 inches
Depth	Door swing and vent space	27 to 30 inches

How to measure your dryer accurately

For the most accurate “will it fit” answer, we measure the dryer in place (or before moving it) and include connections.

• Measure width at the widest cabinet points
• Measure height from floor to the highest point (include the control console)
• Measure depth front-to-back; include the door if it protrudes
• Add space for the vent elbow so the vent is not crushed or kinked
• Confirm the dryer is level; leveling legs can slightly change height

Why it matters

Correct sizing prevents installation problems like a kinked exhaust vent, poor airflow, longer dry times, and overheating. A properly sized space also makes it easier to service common wear items like the dryer idler pulley 279640 if you ever need to access the cabinet.

Last updated: February 2026

Common problems on Kenmore gas dryers like model 11078942892 include no heat, long dry times, not starting, drum not turning, and loud squealing or thumping. Most issues trace back to restricted airflow (lint screen or venting), a door or start switch problem, or normal wear parts in the drum and drive system; see the 11078942892 owner's manual for model-specific troubleshooting steps.

Most common symptoms and what usually causes them

• Dryer will not run: door not fully closed, controls not set to an ON position, or a blown house fuse/tripped breaker (use time-delay fuses where required).
• No heat or weak heat (gas): burner ignition problems (igniter, radiant sensor, gas valve coils), or a safety device opened due to overheating.
• Long drying times: clogged lint screen, crushed/kinked vent, or blocked outside hood causing restricted air movement.
• Drum not turning: worn idler pulley, drum support rollers, or a failing drive motor.
• Loud noise: worn drum support rollers or blower wheel issues.

Quick checks we recommend first (fast, high-impact)

• Clean the lint screen and confirm strong airflow at the outside exhaust hood.
• Inspect the vent run for kinks, crushing, or heavy lint buildup; the manual notes the vent must not be crushed or kinked.
• Confirm the door closes firmly and the cycle/timer is set to a drying cycle before pressing Start.
• If the dryer overheated, correct the venting problem before replacing any safety fuse.

Common parts that fix these problems on this model

Symptom	Likely wear part	Example part for 11078942892
Won’t start or stops mid-cycle	Overheat safety opened	Dryer thermal fuse WP3390719
Squealing, thumping, rumbling	Drum support wear	Support kit WPW10314173
Drum won’t tumble	Belt tension system wear	Dryer idler pulley 279640
Runs but won’t heat (gas)	Burner ignition components	Dryer igniter 279311, dryer valve coil kit 279834

Why it matters

Airflow problems do more than slow drying; they can overheat the dryer and open safety devices, which leads to “no heat” or “won’t run” complaints. Fixing venting first prevents repeat failures and helps the dryer run efficiently.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number plate; on model 11078942892, it’s the number you should record and use anytime you look up parts, troubleshooting steps, or service information in the 11078942892 owner's manual.

Where to find the model and serial number plate

On most Kenmore dryers (including many 110-series gas dryers), the plate is typically in one of these spots:

• Inside the dryer door opening (around the door frame)
• On the front panel just inside the door
• On the back panel of the dryer cabinet
• Near the lint screen housing (depending on the design)

What the model number looks like (and why it matters)

Kenmore model numbers are usually a long string of digits (sometimes with a dot in older formats). For parts matching, use the full model number exactly as shown on the plate.

Quick guide

What you see	What it means	What to do next
Model number (example: 11078942892)	Identifies the exact dryer design	Use it to match parts like a thermal fuse, igniter, or gas valve coil kit
Serial number	Identifies the production unit	Keep it for service history and warranty records

Tips to avoid ordering the wrong part

Even small model differences can change the correct part fit. Before ordering, we recommend:

• Copy the model number character-for-character from the plate
• Compare your symptom to the troubleshooting section in the 11078942892 owner's manual
• Match parts by model, then by part ID (for example, dryer thermal fuse WP3390719)
• If the dryer is noisy or thumping, check common wear items like support kit WPW10314173
• If the dryer runs but will not heat, common gas-heat suspects include dryer igniter 279311 and dryer valve coil kit 279834

Why it matters

Using the exact model number ensures the parts diagrams, repair steps, and replacement parts you choose match your Kenmore gas dryer’s configuration, which saves time and prevents returns.

Last updated: February 2026