Kenmore 110C71492310 gas dryer Parts

For the Kenmore gas dryer model 110C71492310, the cabinet size is about 29 inches wide, 27 3/4 inches deep, and 43 3/8 inches tall. For installation, plan extra space behind the dryer for the exhaust vent elbow; see the 110C71492310 installation guide.

Dimensions and what they mean

These measurements describe the dryer body (not including the space needed for venting and door swing). Your installation space should account for:

• Door clearance so the door opens fully
• Rear clearance for the exhaust vent connection (many installs need at least 5 1/2 inches behind the dryer)
• Side and top clearance if the dryer sits in a closet or recessed area
• A level floor (a slope over 1 inch can affect tumbling and sensor cycles)

Quick reference table

Measurement	Approx. size
Width	29 in.
Depth	27 3/4 in.
Height	43 3/8 in.
Typical rear clearance for vent elbow	5 1/2 in. minimum

Why it matters

Correct sizing prevents crushed venting, poor airflow, and longer dry times. Proper clearance also makes it easier to service common wear items like the belt 341241 without having to pull the dryer out of a tight space.

Last updated: February 2026

For the Kenmore 110C71492310 gas dryer, we troubleshoot by matching the symptom (no heat, won’t start, noisy, long dry times) to a short set of checks: airflow first, then power and door switch, then the gas ignition and safety thermostats. Use the owner's manual for model-specific test points and wiring.

Quick symptom checklist (start here)

• Long dry times or overheating: clean lint screen, check vent for kinks, confirm strong airflow outside.
• Won’t start: confirm power, check door fully closes, test the door switch.
• Runs but no heat: focus on igniter, gas valve coils, radiant sensor, and thermostats.
• Noisy or thumping: inspect belt, drum support rollers, and blower wheel.
• Stops mid-cycle: look for restricted airflow or a tripped high-limit condition.

Step-by-step troubleshooting by symptom

1) Dryer won’t start

• Verify the dryer is plugged in and the breaker is on.
• Confirm the door latches; a failed switch can prevent starting.
• If the drum light works but the motor won’t run, the timer or motor circuit is next.

2) Dryer runs but won’t heat (gas)

• Confirm the gas shutoff valve is open.
• Watch for ignition: igniter glow, then flame.
• If it ignites once then quits, gas valve coils are a top suspect.

3) Long dry times

• Clean the lint screen and lint chute.
• Inspect the entire vent run; keep it short and unobstructed.
• Check blower wheel for looseness or lint buildup.

Parts that commonly solve these symptoms

Symptom	Common part to check	Example from this model
Won’t start	Door switch	Dryer door switch WP3406107
No heat	Ignition system	Igniter 279311
Heats then stops	Gas valve coils	Dryer valve coil kit 279834
Overheats	High-limit protection	Dryer high-limit thermostat W11050897
Squeal/thump	Drum drive	Belt 341241

Why it matters

On gas dryers like the 110C71492310, airflow problems can cause overheating, shutdowns, and repeated thermostat failures; fixing the venting often restores normal heat and drying performance.

Last updated: March 2026

The average lifespan of the Kenmore 110C71492310 gas dryer is 13 years. With good airflow, routine lint cleaning, and timely replacement of wear parts (belt, rollers, thermostats), this model typically reaches that service life without major performance loss.

What affects lifespan the most

• Vent restriction (the biggest life-shortener): causes overheating and repeated thermal failures.
• Load size and cycle choice: frequent heavy loads increase belt and roller wear.
• Lint management: lint buildup stresses the blower and heating system.
• Installation quality: crushed or long vent runs increase heat and run time.
• Preventive part replacement: addressing noise early prevents secondary damage.

Typical wear parts over a dryer’s life

Part type	What you notice	Example part for this model
Drum drive	Drum won’t turn, squeal, burning rubber smell	Belt 341241
Drum support	Thumping, rumbling, uneven drum movement	Dryer repair kit 4392065
Gas ignition	No heat or intermittent heat	Dryer valve coil kit 279834
Overheat protection	Shuts off, overheats, no heat after vent issues	Dryer operating thermostat WP3387134

Maintenance that extends life (do these regularly)

• Clean the lint screen every load; wash it occasionally to remove residue.
• Check airflow at the outside vent; it should be strong and steady.
• Clean the vent duct at least yearly (more often with long runs).
• Stop using the dryer if you hear persistent squealing or thumping; inspect drum support parts.
• Follow the venting and clearance guidance in the installation guide.

Why it matters

A gas dryer can last its full 13-year lifespan only if it can move air efficiently; proper venting reduces heat stress on the burner system, thermostats, motor, and drum support components.

Last updated: March 2026