Kenmore Elite 66513773K600 dishwasher Parts

For the Kenmore Elite dishwasher model 66513773K600, the most reliable “hard reset” is to cancel the current cycle and drain, then restart a fresh cycle. Use the CANCEL/DRAIN button; the dishwasher will run a drain for about 2 minutes if needed. See the steps in the 66513773K600 owner's manual.

Quick reset steps (CANCEL/DRAIN method)

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Press CANCEL/DRAIN (the Cancel light should come on).
• Close the door to let the dishwasher drain (about 2 minutes, if needed).
• When the Cancel light turns off, open the door.
• Select a new cycle and options.
• Press START/RESUME and firmly close the door.

If the controls seem “stuck”

Sometimes the control panel looks frozen because the dishwasher is still trying to drain or finish a step.

What you see	What it usually means	What to do
Cancel light on	Cancel/drain is active	Let the 2-minute drain finish
Start/Resume flashing	Door opened mid-cycle	Close door, then press START/RESUME
Won’t respond to new selections	Cycle not cleared	Press CANCEL/DRAIN, then reselect cycle

Why it matters

Canceling and draining clears the active cycle logic so the dishwasher can start over with correct water level and timing. It also helps prevent starting a new wash with leftover dirty water in the sump.

When to suspect a real problem (not a reset issue)

If cancel/drain runs but the tub still holds water, focus on the drain path:

• Check the sink/disposer connection for a clog.
• Make sure the drain hose is not kinked or crushed.
• If the dishwasher hums but won’t pump out, the drain pump may be failing.

A common replacement for this model is the dishwasher drain pump WPW10348269.

Last updated: January 2026

On a Kenmore Elite dishwasher model 66513773K600, an E25 error typically points to a drain problem, most often a blocked drain pump or an issue with the drain pump cover (loose, missing, or not seated). Use the steps in the 66513773K600 owner's manual to confirm the exact reset and drain-check procedure for your control panel.

What to check first (fast, common fixes)

• Cancel the cycle and let the unit attempt to drain.
• Check the tub bottom and filter area for labels, glass, bones, or food debris.
• Inspect the drain hose routing for kinks or a clogged high loop/air gap.
• Verify the sink/disposer inlet is clear (new disposer plugs are a common cause).
• Restore power and run the shortest cycle to confirm draining (the installation guide recommends starting the dishwasher and checking for water in the tub early in the cycle).

Parts that commonly relate to an E25 drain issue

If the dishwasher hums but will not drain, drains slowly, or stops with standing water, these model-matched parts are common suspects:

Symptom	Most likely area	Example model-matched part
Standing water, pump hums	Drain pump jammed or failing	Dishwasher drain pump WPW10348269
Slow drain or backflow	Drain path restriction	Dishwasher drain hose (routing/clog)
Intermittent drain, odd noises	Pump/impeller wear	Pump components in sump area

Why it matters

A true E25 drain fault can leave dirty water in the tub, cause odors, and prevent the dishwasher from completing the cycle. Clearing the drain path early also helps protect the circulation system and reduces repeat error codes.

Helpful DIY reference

For model-family troubleshooting patterns and what to do when codes repeat, use our Kenmore 665 model dishwasher error codes guide.

Last updated: January 2026

On your Kenmore Elite dishwasher model 66513773K600, the model number is printed on the model and serial number label inside the dishwasher tub. Open the door and look along the tub frame area; the label is shown in the parts and features section of the owner's manual.

Where to look (fast checklist)

• Open the dishwasher door fully.
• Look for the model and serial number label inside the tub opening.
• Check the tub frame/door opening area where the door seals against the tub.
• Wipe the area with a damp cloth if the label is hard to read.
• Write down both the model number and serial number for parts matching.

What to record and why

The manual recommends recording these details so you can match parts and get the right diagrams.

Item to write down	Example format	What it’s used for
Model number	66513773K600	Ensures correct part fit and diagrams
Serial number	Letters and numbers	Helps identify production version
Purchase date	Month/day/year	Useful for your own records

Why it matters

Kenmore dishwashers often have multiple versions that look similar. Using the exact model number (66513773K600) helps us match the correct components like the drain pump, water inlet valve, or electronic control board so you avoid ordering the wrong part.

Last updated: March 2026