Kenmore 58715163401 dishwasher Parts

On the Kenmore 58715163401 dishwasher, the filter area is on the bottom of the tub under the lower spray arm. This model uses a self-cleaning filter system, and the serviceable piece you typically access is the glass trap in the center of the filter.

Where to look (inside the tub)

1. Open the door and pull out the lower rack.
2. Look at the very bottom center of the tub, beneath the lower spray arm.
3. Find the glass trap handle in the center of the filter area.

How to remove and reinstall the glass trap

Before you start, let the heating element cool.

• Remove the lower rack for clear access.
• Grasp the glass trap handle in the center of the tub.
• Lift the glass trap straight up.
• Empty any debris (glass pieces, bones, pits, straws).
• Rinse if needed, then set it back into place so it sits down fully.

For diagrams and the exact component locations for your model, use the 58715163401 owner's manual.

What “self-cleaning filter” means on this model

This dishwasher filters the wash water as it runs and directs food soil into a collection area; you normally do not remove a flat, twist-lock filter like on many newer designs. The main routine maintenance item called out is the removable glass trap.

Item	Location	What you do
Glass trap	Bottom center of tub	Lift out, empty, reinstall
Self-cleaning filter system	Under the tub and spray arm area	No regular removal; keep debris cleared

Why it matters

Keeping the glass trap clear helps protect the pump and wash system, improves cleaning performance, and reduces the chance of drainage issues caused by hard debris.

Last updated: February 2026

To hard reset your Kenmore dishwasher model 58715163401, we recommend using the control-panel reset sequence listed in the 58715163401 owner's manual. In most cases, a reset clears a stuck cycle, restores normal button response, and lets you restart a wash cycle normally.

Quick reset steps (most common)

• Press Cancel/Drain once, then wait for the drain to finish (often 1 to 2 minutes).
• Turn the dishwasher off (or press Power) if your model has that button.
• Wait 3 minutes with the door closed.
• Turn it back on.
• Select Normal and press Start.

If the buttons are unresponsive

Try a full power reset (this is the closest thing to a true hard reset):

• Turn off power to the dishwasher at the circuit breaker.
• Wait 3 to 5 minutes.
• Restore power.
• Start a Normal cycle and listen for filling and wash motor operation.

What a reset fixes (and what it does not)

Symptom	Reset helps?	What to check next
Cycle stuck or won’t advance	Often	Door fully latched; try Cancel/Drain
Control panel acting “frozen”	Often	Power reset at breaker
Won’t fill with water	Sometimes	Water supply valve open; inlet valve
Not cleaning well	No	Spray arm clogs; filter and loading

Why it matters

A reset is a fast first step because it clears many temporary control issues without replacing parts. If the dishwasher still will not start, fill, or wash after a reset, the problem is usually a door-latch issue, water-fill issue, or wash-system blockage.

Parts that commonly relate to “won’t start” or “won’t run right” symptoms

• Door not latching consistently: latch assembly A00104102 and strike 154662601
• Overfilling or fill problems: switch 154773201 (float switch) and valve 154637401 (water inlet valve)
• Poor wash performance: dishwasher spray arm 5304517203

Last updated: February 2026

Common problems on Kenmore dishwashers like model 58715163401 include poor cleaning from blocked spray arms or filters, draining problems from clogs, leaks from worn seals, and “won’t start” issues tied to the door latch. Our 58715163401 owner's manual also notes normal operating pauses and sound changes during spray-arm switching.

Most common symptoms and what usually causes them

• Not cleaning well: spray arm ports blocked, filter/collection area loaded with soil, low incoming water temperature
• Not draining: drain path restriction (air gap or disposer connection), kinked hose, sump debris
• Leaking: excess suds from wrong detergent, spilled rinse aid, unit not level, worn door seal
• Not drying: rinse aid empty, heated dry option off, heater or thermostat issue
• Won’t start: door not fully latched, latch/strike misalignment, control not set correctly

Quick checks we recommend first (fast, no parts)

1. Confirm the dishwasher is level and the door closes smoothly.
2. Use automatic dishwasher detergent only and measure carefully (too much can cause foam and overflow).
3. Verify incoming water temperature is about 120°F (49°C) and home water pressure is typically 20 to 120 psi.
4. Make sure dishes are loaded so they do not block spray arm rotation.
5. Clean the filter area and remove visible debris from the sump.

Parts that commonly fix these problems on 58715163401

Symptom	Common part to inspect	What it affects
Poor cleaning	Dishwasher spray arm 5304517203	Wash coverage and spray force
Leaks at door	Gasket 809006501	Door sealing at the lower edge
Not filling or weak wash	Valve 154637401	Water entering the dishwasher
Not heating or poor drying	Heater 154665201	Water heating and heated dry
Overfilling	Switch 154773201	Float/overfill protection

Why it matters

Most “dishwasher problems” are really water flow, temperature, or sealing issues. Fixing the root cause improves cleaning, prevents leaks, and helps the wash system recirculate filtered water the way it was designed.

Last updated: February 2026

Kenmore dishwasher model 58715163401 is a built-in dishwasher that fits a standard under-counter opening. For the exact overall dimensions and the required cabinet cutout measurements for your specific installation, use the specifications section in the 58715163401 owner's manual.

Typical size you should plan for

Most Kenmore built-in dishwashers of this style are designed around standard cabinetry. Use these typical ranges to sanity-check your opening before you measure for exact fit.

• Width: typically about 24 inches (some built-ins are 18 inches, but that is a different size class)
• Height: typically 33 1/2 to 35 inches (often adjustable at the leveling legs)
• Depth: typically 24 to 27 inches depending on door and handle style

How to measure your cabinet opening (quick checklist)

Measure in three spots (top, middle, bottom) because cabinets can be out of square.

• Measure opening width between the cabinets
• Measure opening height from floor to underside of countertop
• Measure opening depth to the back wall
• Confirm space for the water line, drain hose, and power routing
• Check that the door opens fully without hitting an island or adjacent hardware

Built-in dishwasher sizing guide

Measurement	What to measure	Typical target
Width	Left cabinet to right cabinet	~24 in.
Height	Floor to underside of countertop	33 1/2 to 35 in.
Depth	Front of cabinets to back wall	24 to 27 in.

Why it matters

Correct sizing prevents installation problems like a dishwasher that sits too low, a door that rubs the cabinet face, or hoses that kink. It also helps when replacing fit-sensitive parts such as the gasket 809006501 if you are addressing leaks at the bottom of the door.

Last updated: February 2026