Kenmore 11047512602 washer Parts

The Kenmore washer model 11047512602 is a front-load washer; most Kenmore front-load washers in this style run in the 3.0 to 4.5 cu. ft. range. For the exact cubic-foot capacity for your unit, use the specifications section in the 11047512602 owner's manual.

Use these quick checks to locate the official capacity listing:

• Open the 11047512602 owner's manual and look for Specifications, Features and benefits, or Product data
• Search the PDF for terms like capacity, cu. ft., tub volume, or basket volume
• Confirm the model number on the washer’s rating label (commonly around the door opening) matches 11047512602
• If you have a pedestal or stack kit installed, verify you are reading washer specs, not accessory dimensions

These ranges help you sanity-check what you find in the manual:

Capacity affects load size, wash performance, and vibration control. Loading beyond the intended capacity reduces tumbling action and can contribute to out-of-balance conditions and longer cycle times.

If you are planning a laundry-room fit, the manual also lists installation clearances and overall dimensions. Those measurements help confirm undercounter or closet installation separately from wash capacity.

Last updated: February 2026

To force your Kenmore washer model 11047512602 to drain, we use the control-panel manual drain: press STOP, choose RINSE/DRAIN & SPIN, turn off 2ND RINSE, then press and hold START for about 1 second to begin draining (see the 11047512602 owner's manual).

• Press STOP once.
• Select RINSE/DRAIN & SPIN.
• Press 2ND RINSE so the 2nd rinse option is deselected.
• Press and hold START (about 1 second) to start the drain.
• Wait for the cycle to finish; the door unlocks after the spin completes.

A no-drain condition is usually a restriction in the drain path or a drain pump issue.

• Check the drain hose for kinks, crushing, or a clog.
• Make sure the hose is installed to prevent siphoning (do not force excess hose into the standpipe; do not seal the standpipe connection).
• Verify the standpipe or laundry tub is draining freely.
• If you hear the pump hum but water does not move, inspect the pump and hoses for blockage; replace the pump if needed using the water pump WPW10730972.

Forcing a drain the right way protects the door lock system and helps prevent leaks or siphoning that can pull dirty water back into the tub. Correct drain hose routing also helps protect your floor from water damage.

Last updated: February 2026

Your Kenmore washer model number is printed on the appliance’s model and serial tag. On the Kenmore 11047512602 front-load washer, it’s typically located around the door opening area or on the rear panel; match the full number exactly to ensure the correct parts and service information.

Check these common tag locations first:

• Front-load washers: inside the door opening, along the door frame, or behind/around the door opening
• Top-load washers: under the lid, around the tub opening, or on the underside of the lid
• Any style: back panel near the power cord, or along the cabinet edge near the control area

For Kenmore laundry products, the model number is often a long numeric string (commonly starting with 110 on many Kenmore-built units). Record it exactly as shown, including all digits.

• Copy the model number directly from the tag, not from a receipt or listing
• Use the full model number (no shortened versions)
• If the tag is worn, take a clear photo and zoom in to confirm digits
• Cross-check the model number in the 11047512602 owner's manual

Kenmore washers can look similar across multiple series, but parts like the door boot, drain pump, and electronic control vary by model. Using the exact model number helps us match the correct diagrams and parts for your washer.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use and routine care. For your Kenmore model 11047512602, consistent cleaning, correct loading, and timely replacement of wear items (like belts and pumps) are the biggest factors in reaching that range.

Most washers land in the same general window, but real-world lifespan depends on usage and maintenance.

• Loads per week: more cycles equals more wear on the drive system and drain components
• Detergent habits: too much HE detergent can cause residue and odors that lead to service issues
• Drain health: slow draining strains the pump and can leave water behind
• Vibration control: an unlevel washer increases wear on suspension and tub components
• Water quality: hard water can increase buildup and reduce efficiency

These parts are normal “maintenance” items and are often replaced during the life of the washer.

• Repair makes sense when the issue is isolated (leak at the door boot, no-drain pump failure, worn belt).
• Replacement makes sense when you have repeated breakdowns, heavy tub or bearing noise, or multiple high-cost parts needed at once.

Planning around the 10 to 15 year lifespan helps you avoid surprise downtime. Basic care steps in the maintenance section of the 11047512602 owner’s manual (cleaning, hose checks, storage and moving care) help prevent the most common failures and extend service life.

Last updated: February 2026