Kenmore 25370412410 refrigerator Parts

Your Kenmore refrigerator model number is printed on the appliance’s rating label. On Kenmore model 25370412410, you will typically find that label inside the fresh food compartment or freezer area, or on the cabinet frame behind a drawer or the toe grille.

Where to look for the model number label

Check these common spots on Kenmore refrigerators:

• Inside the refrigerator compartment on a side wall
• Inside the refrigerator compartment on the ceiling area near the controls
• On the cabinet frame behind the lower crisper drawer (remove the drawer to see the wall)
• Inside the freezer compartment on a side wall
• Behind the toe grille or kick plate at the bottom front (if your design allows access)

What the label looks like and what to write down

The rating label usually includes several identifiers. Record them exactly as shown:

• Model number (the key identifier for parts lookup)
• Serial number (helps confirm production details)
• Electrical ratings (voltage/amps)
• Refrigerant information (service-related)

Quick ID checklist

Item	Why it matters	Example format
Model number	Ensures correct parts fit	25370412410
Serial number	Helps match revisions	Letters and numbers
Brand	Confirms product family	Kenmore

Why it matters

We use the model number to match exact-fit parts and diagrams for your refrigerator, such as a compatible water filter, door gasket, or control board. Even small model-number differences can change which parts fit.

Helpful next steps once you find it

• Compare the label’s model number to your paperwork and keep a photo for reference
• Use the model number when ordering maintenance items like the Kenmore refrigerator water filter 9999
• For location and handling details during setup, follow the installation guide

Last updated: February 2026

Your Kenmore refrigerator model 25370412410 has a fixed factory capacity (in cubic feet) that is tied to the model’s design; the most accurate way to get the exact number is to check the specifications listed in the 25370412410 owner's manual. Measuring the cabinet and doing a length x width x height calculation estimates interior volume, but it rarely matches the true rated capacity.

How to find the exact cubic feet for model 25370412410

We recommend using the spec information in the manual because “cubic feet” is a rated storage capacity, not a simple outside-dimension calculation.

• Look for Specifications, Product dimensions, or Capacity in the 25370412410 owner's manual
• Use the model number 25370412410 (not just “Kenmore 253”) when searching within the manual
• If you see multiple capacities listed, use the one labeled total capacity (not freezer-only)
• If the manual lists dimensions only, use them for fit checks, not for capacity

If you want to estimate cubic feet from measurements

An estimate can be helpful when comparing space, but it is not the same as the manufacturer’s rated capacity.

Formula

What you measure	Convert to	Calculation
Interior height, width, depth (inches)	Cubic feet	(H x W x D) ÷ 1728

Tips for a better estimate

• Measure the interior usable space, not the outside cabinet
• Subtract space taken by shelves, bins, drawers, and the ice maker housing
• Measure the fresh food and freezer sections separately, then add them

Why it matters

Using the correct cubic feet helps when planning food storage, comparing models, and choosing organization parts like a frigidaire refrigerator crisper drawer 241801808 or a frigidaire refrigerator door bin 242079701 that fit your layout.

Last updated: February 2026

A bad compressor in your Kenmore 25370412410 bottom-mount refrigerator usually shows up as poor cooling with the unit running a lot, repeated clicking as it tries to start, or the compressor not running at all. Before condemning the compressor, we rule out airflow, control settings, and power issues using the checks in the owner's manual.

Quick symptoms that point to a compressor problem

• Refrigerator and freezer temperatures stay warm even though the unit runs often.
• You hear a repeated click every few minutes (start attempt, then shutoff).
• The compressor is very hot to the touch after trying to run (do not touch bare tubing).
• The condenser fan runs but cooling does not improve.
• The compressor is silent and never starts (not in a defrost cycle).

Checks to do first (most common non-compressor causes)

1. Confirm controls are set correctly: A control set to OFF/0 can make it look like a compressor failure.
2. Allow for defrost: A normal defrost cycle can stop cooling briefly (often around 30 minutes).
3. Verify power: Make sure the cord is fully seated; check the house breaker or fuse.
4. Check door sealing: A leaking door seal can cause long run times and warm temps; inspect the gasket for gaps, dirt, or damage.
5. Confirm airflow is not blocked: Keep vents clear and do not block the toe grille area.

What a technician tests to confirm a bad compressor

These checks require a meter and refrigeration know-how:

• Compressor start and run winding resistance and continuity
• Amperage draw at startup and while running
• Start device performance (if used on this design)
• System pressures and signs of a sealed-system restriction or refrigerant loss

What you notice	More likely cause	What to do next
Clicking, no cooling	Start device issue or compressor locked	Have electrical start circuit and compressor tested
Runs constantly, weak cooling	Dirty coils, airflow issue, door leak, sealed-system issue	Check gasket and airflow; then sealed-system diagnosis
Not running at all	Control setting, defrost, power, control board	Verify settings and power; then diagnose controls

Why it matters

Replacing a compressor is a sealed-system repair; the symptoms can look similar to simpler issues like a door gasket leak or a control setting problem. Doing the basic checks first prevents unnecessary parts replacement.

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life under normal household use. For your Kenmore 25370412410 bottom-mount refrigerator, regular maintenance (especially keeping airflow clear and seals tight) is what most directly determines whether it lands closer to 10 years or closer to 15.

Typical lifespan ranges (what to expect)

Here are realistic, industry-typical ranges for a Kenmore refrigerator like model 25370412410:

• Average: 10 to 15 years
• Often achievable with good care: 15 years
• Shortened lifespan drivers: poor airflow, dirty condenser area, weak door seals, repeated icing or temperature swings

Lifespan outcome	What it usually looks like	Common contributors
10 years	More frequent repairs start showing up	heat buildup, heavy use, neglected cleaning
12 to 15 years	Normal, cost-effective ownership	routine cleaning, stable temps
15+ years	Fewer major failures	consistent maintenance, quick fixes

Maintenance that most affects lifespan

We recommend focusing on the items that reduce compressor run time and prevent moisture problems:

• Keep the refrigerator level and the doors sealing evenly (a poor seal makes the unit run longer).
• Confirm the freezer drawer gasket seals on all sides after any removal or adjustment (the installation checklist calls out checking the gasket seal). Use the steps in the installation guide.
• Replace the water filter on schedule if your unit dispenses water or makes ice; the manual recommends about every 6 months for best water quality.
• If you need the correct replacement filter for this model, use the Kenmore refrigerator water filter 9999.
• Address unusual noises or warm temperatures quickly; long run times and overheating shorten component life.

Why it matters

A refrigerator usually does not “wear out” all at once; lifespan is mostly about how long major sealed-system and airflow components (compressor, fans, controls, gaskets) can operate without being overstressed. Good sealing and good airflow reduce run time, which directly reduces wear.

Last updated: February 2026