Kenmore Elite 79572053114 refrigerator Parts

For Kenmore Elite refrigerator model 79572053114, the correct water filter is the one specified for that exact model in the 79572053114 owner's manual. On this model, the matching replacement we list is genuine Kenmore refrigerator water filter 9690 AGF80300801.

Quick ways to confirm the right filter

• Match the refrigerator model number on the rating label to 79572053114.
• Check the water filter section in the manual for the filter type and replacement interval.
• Look at the existing cartridge and compare its markings to the replacement listing.
• If you are temporarily out of filters, use the refrigerator's bypass plug (the manual notes you must have a filter or bypass plug installed).
• Replace the filter on schedule to avoid reduced flow and taste issues.

Replacement timing and what to expect after changing it

The manual guidance for this style of Kenmore bottom-mount refrigerator is to replace the disposable water filter every 6 months, or sooner if flow drops or the indicator turns on.

After installing a new filter:

• Flush about 2.5 gallons of water to clear trapped air and contaminants.
• Use 30 seconds ON, 60 seconds OFF dispensing cycles so you do not run the dispenser continuously.

Water supply specs that affect filter performance

Keeping water pressure and temperature in range helps the filter and ice maker work correctly.

Item	Typical spec for this model family (from the manual)
Water pressure	40 to 120 psi
Water temperature	33°F to 100°F
Service flow	0.5 gpm

Why it matters

Using the correct filter for 79572053114 protects water taste, helps maintain normal dispenser flow, and supports consistent ice cube size. The wrong cartridge fit can cause leaks, poor flow, or bypassing filtration.

Last updated: February 2026

To level a Kenmore Elite refrigerator model 79572053114, we adjust the two front leveling legs until the cabinet is steady and both fresh food doors close easily. For best door closing, the front should sit slightly higher than the rear; follow the steps in the 79572053114 owner's manual.

Tools and prep

• 11/16-inch wrench or a flat-blade screwdriver (as specified for this model)
• A helper to gently push back on the top of the refrigerator (reduces weight on the legs)
• A small level (optional, but helpful)
• Clear space so the unit can slide in and out safely

Leveling steps (front-to-back and side-to-side)

1. Pull the refrigerator forward enough to access the front leveling legs.
2. Raise a side: turn the leveling leg left.
3. Lower a side: turn the leveling leg right.
4. Make small adjustments; it often takes several turns to change the tilt.
5. Open and close both fresh food doors; if they do not close easily, raise the front slightly more by turning both leveling legs to the left the same amount.

Quick checks that confirm it is level enough

• The refrigerator does not rock when you press on the corners.
• Both doors close fully without drifting open.
• Door gaps look even after leveling (if not, use the door alignment adjustment described in the manual).

Leveling targets (practical guide)

What you notice	What to adjust	What you should see after
Cabinet rocks	Raise the low front corner	No wobble on the floor
Doors do not self-close	Raise the front slightly (both legs)	Doors close more easily
Doors look uneven	Use door alignment nut on bottom hinge	Even gap between doors

Why it matters

Proper leveling reduces vibration and noise, helps the doors seal consistently, and supports stable temperatures in the fresh food and freezer compartments.

Last updated: February 2026

Common problems on the Kenmore Elite 79572053114 bottom-mount refrigerator include warm temperatures from airflow restrictions (dirty condenser coil, blocked vents), defrost system trouble that causes frost buildup, water and ice dispenser issues, and door sealing problems that let warm air leak in. Use the 79572053114 owner's manual troubleshooting section to narrow the cause.

Most common symptoms and what they usually point to

• Refrigerator not cold enough: dirty condenser coil, condenser fan issue, evaporator fan issue, or sealed system/compressor problem
• Freezer cold but fresh food warm: air damper stuck, blocked return vents, frost-packed evaporator
• Ice maker not making ice: water supply issue, clogged filter, ice maker assembly fault
• Water dispenser slow or no water: restricted filter, kinked water tubing, low house water pressure
• Water leaking or puddles: clogged/iced drain path, door left ajar, gasket not sealing
• Lights not working or door alarm issues: door switch problem

Quick checks we recommend before replacing parts

1. Confirm controls are set correctly and doors fully close.
2. Clean dust from the condenser area and make sure airflow around the cabinet is clear.
3. Check that food packages are not blocking air vents in the refrigerator or freezer.
4. Look for heavy frost on the freezer back wall (often a defrost airflow problem).
5. If you have a dispenser, replace the water filter on schedule and flush several gallons after.

Parts that commonly solve these issues on model 79572053114

Problem area	Common fix	Example part for this model
Bad taste/slow water	Replace water filter	Genuine Kenmore refrigerator water filter 9690 AGF80300801
Odors in fresh food section	Replace air filter	Lg refrigerator air filter ADQ73214408
Door not sensing closed	Replace door switch	Refrigerator door switch 6600JB1010A
Warm temps from poor heat rejection	Clean or replace condenser coil	Refrigerator condenser coil ACG73645004

Why it matters

Most “not cooling” complaints start as an airflow or maintenance issue (coil cleaning, vents, filters). Catching those early helps prevent longer run times, temperature swings, and ice maker or water dispenser problems.

Last updated: February 2026

On Kenmore Elite refrigerator model 79572053114, dH typically indicates a defrost heater (defrost heating) problem, meaning the refrigerator is not warming the evaporator enough during the defrost cycle. Start by checking for heavy frost buildup and then test the defrost circuit components listed in the 79572053114 owner's manual.

What to check first (fast, no tools)

• Unplug the refrigerator for safety.
• Look for thick frost on the rear freezer panel; heavy frost points to a defrost failure.
• Make sure the freezer door closes fully and the gasket seals.
• Confirm the temperature settings are normal (freezer around 0°F, fresh food around 37°F).
• Restore power and listen for the evaporator fan; no airflow can mimic a defrost issue.

Likely causes of a dH code

A dH code is usually triggered when the control does not see the expected temperature change during defrost.

What can fail	What you may notice	What to do next
Defrost heater circuit	Frost blanket on evaporator, warm fridge section	Test heater and wiring continuity (power off)
Defrost sensor	Defrost runs but does not terminate correctly	Test sensor resistance at known temperature
Control not switching defrost	Repeated dH, inconsistent cooling	Check for output voltage to heater during forced defrost
Airflow restriction	Warm fresh food, freezer looks “packed”	Clear vents, avoid blocking return air

Parts that are commonly involved

These parts are not always the cause, but they are frequently checked during dH troubleshooting:

• Refrigerator defrost sensor assembly 6615JB2005R (sensor feedback for defrost control)
• Wiring connections at the evaporator area (loose or corroded connectors)
• Main control logic (if sensor and heater circuit test good)

Why it matters

When defrost heat is not working correctly, frost builds up on the evaporator and blocks airflow. That reduces cooling to the fresh food section, can cause longer run times, and can lead to temperature swings that spoil food.

Helpful reference

For model-family code meanings and reset steps, use Kenmore 795 model bottom freezer refrigerator error codes.

Last updated: February 2026

A Kenmore Elite refrigerator like model 79572053114 typically lasts 10 to 15 years. Regular maintenance (keeping airflow clear, cleaning dust from the condenser area, and maintaining tight door seals) helps it reach the high end of that range.

Typical lifespan and what affects it

Most bottom-mount refrigerators land in the same general window, but these factors make the biggest difference:

• Condenser cleanliness: dust buildup makes the compressor run hotter and longer
• Door seal condition: air leaks cause longer run times and temperature swings
• Ice maker and water system upkeep: clogged filters and low water flow strain components
• Vent clearance: blocked vents reduce cooling efficiency
• Room conditions: hot garages and tight enclosures increase workload

Maintenance checklist (high impact, low effort)

We recommend these habits to extend life and reduce common failures:

• Replace the water filter on schedule; use the correct filter for this model, such as genuine Kenmore refrigerator water filter 9690 AGF80300801
• Keep the fresh air system maintained; replace the lg refrigerator air filter ADQ73214408 when odors linger
• Vacuum dust from the condenser area and surrounding vents
• Confirm doors close fully and do not bounce open
• Keep food from blocking interior air vents

Repair vs. replace quick guide

Use age plus symptoms to decide where to put your money.

If your refrigerator is…	And you see…	Best next step
Under 8 years old	minor issues (warm spots, slow ice)	troubleshoot and repair
10 to 15 years old	repeated cooling problems	price key parts and compare
Over 15 years old	sealed system or compressor symptoms	consider replacement value

Why it matters

A refrigerator near the end of its expected lifespan is more likely to develop cooling issues tied to airflow, seals, or major components such as the compressor. Staying ahead of filters and airflow reduces run time, energy use, and wear.

For model-specific care and maintenance intervals, follow the 79572053114 owner's manual.

Last updated: February 2026

On Kenmore Elite model 79572053114, the model and serial number label is typically inside the fresh food (refrigerator) compartment on a side wall near the crisper drawers, or on the cabinet frame behind the lower crisper pan. Confirm the exact label location in the 79572053114 owner's manual.

Common places to check first

• Inside the refrigerator section on the left or right interior wall
• On the cabinet frame behind the lower crisper drawer (remove the drawer to see the label)
• Along the door opening (hinge side) on the cabinet frame
• Behind the front toe grille or kick plate area (less common, but worth checking)
• On the back exterior panel near the bottom (usually harder to access)

Quick steps to find it fast

1. Open the refrigerator door and pull out the lower crisper drawer.
2. Look for a white or silver sticker on the cabinet wall or frame.
3. Wipe condensation or dust off the label so the full number is readable.
4. Write down both the model and serial number.

What the label usually looks like

Item on label	What it’s used for	Example for your fridge
Model number	Matching parts and diagrams	79572053114
Serial number	Date code and service identification	Varies by unit

Why it matters

We use the full model number to match the correct Kenmore Elite bottom-mount refrigerator parts (like a water filter, door gasket, or control board). Even small model variations can change which parts fit.

Last updated: February 2026

Water pooling inside the bottom of your Kenmore Elite refrigerator model 79572053114 is almost always caused by a clogged or frozen defrost drain that forces defrost water to overflow into the fresh food section. Less often, a leaking water supply line, filter area, or a poor door seal can add moisture that collects at the bottom; use the steps below and confirm locations in the 79572053114 owner's manual.

Most common causes (and what to check first)

• Defrost drain clogged with food debris or ice; water cannot reach the drain pan.
• Drain tube frozen; defrost water backs up and spills into the refrigerator.
• Door not sealing; warm, humid air creates excess frost that later melts.
• Water filter or tubing seep; slow leaks can run down and pool.
• Ice maker or dispenser line leak; water tracks along internal panels.

Quick troubleshooting steps

1. Unplug the refrigerator and remove food from the bottom area.
2. Look for a sheet of ice or water trail starting at the back wall; that pattern points to a drain issue.
3. Clear the drain:
   • Melt visible ice with warm (not boiling) water.
   • Flush the drain opening with warm water using a turkey baster.
4. Inspect the filter and lines:
   • Check around the filter area for drips; replace the filter if the housing is cracked or the filter is not seated.
   • Inspect the line for kinks or splits; the model uses internal tubing such as refrigerator water tubing MJU62070602.
5. Check the door seal:
   • Close a dollar bill in the gasket; it should resist pulling out.
   • Clean the gasket and mating surface; reshape with warm water if warped.

Symptom-to-cause guide

What you see	Most likely cause	Best next step
Water after a defrost cycle; ice on back wall	Defrost drain frozen/clogged	Thaw and flush drain
Slow puddle even when not defrosting	Water line or filter seep	Inspect tubing and filter seating
Frost buildup, then water later	Door not sealing	Clean/adjust gasket and door alignment

Why it matters

Pooling water can lead to ice buildup, food spoilage, and floor leaks if it overflows. Fixing the drain or a small seep early prevents repeat icing and protects components like the evaporator fan and control areas.

For model-specific diagrams and access points, follow the 79572053114 owner's manual. For filter-related issues, we also use how to replace the water filter in a Kenmore refrigerator to match the correct replacement and installation steps.

Last updated: February 2026