Kenmore 58715194400 dishwasher Parts

Most Kenmore 58715194400 dishwashers are standard built-in units designed for a 24-inch-wide cabinet opening, with an adjustable height to fit common countertop cutouts. For the exact cutout and leveling targets for your installation, use the 58715194400 installation guide.

Typical dimensions you should plan around

For this Kenmore dishwasher style, these are the measurements that matter most during install:

• Width (opening): 24 inches (standard built-in)
• Height (opening): typically 33-3/4 to 35 inches, adjusted with leveling legs
• Depth: typically around 24 inches plus door clearance in front
• Leveling: unit must be level side-to-side and front-to-back for proper draining and door sealing

What the installation guide confirms for fit

The installation instructions focus on cabinet opening height and leveling leg adjustment:

• If the opening height is at least 33-3/4 inches, the dishwasher fits without modifying the countertop or flooring.
• The front and rear leveling legs are used to raise or lower the dishwasher to match the opening.
• The dishwasher must be checked with a level at the tub and at the opened door to confirm proper alignment.

Quick fit checklist

• Measure from the underside of the countertop to the floor.
• Confirm you have at least 33-3/4 inches of height.
• Adjust front and rear levelers until the tub is level.
• Verify the door closes evenly and the tub gasket seals.

Size planning table (what to measure)

What you measure	Where to measure	What you want to see
Cabinet opening width	Inside of cabinet walls	24-inch built-in opening
Cabinet opening height	Countertop underside to floor	33-3/4 inches minimum
Front clearance	In front of dishwasher	Enough room for door to open fully
Level	Across tub front and on opened door	Bubble centered both ways

Why it matters

Correct sizing and leveling prevents common problems like door leaks, poor draining, and noisy operation. A dishwasher that is even slightly out of level can stress the door seal and affect wash performance.

Last updated: February 2026

Your Kenmore dishwasher model number is printed on the model and serial number label inside the tub. For Kenmore model 58715194400, the label is on the right side of the tub, and the model number typically begins with 587. (followed by more digits).

Where to look first (fastest checks)

• Open the dishwasher door fully.
• Look along the right interior tub wall for the model/serial label.
• Wipe the area with a damp cloth; labels can be hard to read through residue.
• Write down the full model number and serial number exactly as shown.
• Use the full model number when ordering parts like a door seal, drain hose, or water inlet valve.

What the label looks like and what you need

The label includes both the model and serial number. Record both so we can match the correct parts and troubleshooting info.

What to record	Example format you may see	Why it matters
Model number	587.1519_ _ (varies by color/version)	Ensures correct part fit and diagrams
Serial number	Letters and numbers	Helps identify production details
Purchase date (optional)	Month/day/year	Useful for service history

Why it matters

Kenmore dishwashers can look similar across series, but internal components (like the wash system parts, heating element, and door latch pieces) can differ. Using the exact model number prevents ordering the wrong replacement part.

Helpful references for this model

• Use the 58715194400 owner’s manual to see the “Dishwasher features” section that shows the label location.
• If you are installing or repositioning the unit, the 58715194400 installation guide covers utility connections and placement considerations.

Last updated: February 2026

Yes. We still carry replacement parts for many Kenmore dishwashers, including model 58715194400. The key is matching parts by the full model number so you get the correct fit for common repairs like leaks, draining problems, and door sealing; use the 58715194400 owner's manual to confirm the symptom and component location.

How to find the right part for your Kenmore dishwasher

Use your model number (58715194400) and then match the part by name and function.

• Check the serial/model label location (typically on the right side of the tub opening)
• Identify the symptom first (leak, no drain, not filling, door won’t latch)
• Compare the part name and ID, not just a “looks similar” photo
• Replace seals and hoses when they show cracking, flattening, or mineral buildup
• After any repair, run a short cycle and inspect for leaks at the door and under the unit

Common parts people replace on model 58715194400

These are frequent wear items for this Kenmore dishwasher.

Symptom	Likely part to check	Example part for this model
Water leaking at the bottom of the door	Lower door seal	Gasket 809006501
Dishwasher won’t drain or drains slowly	Drain hose or drain pump	Hose 807117001, dishwasher drain pump A00126501
Dishwasher not filling or fills slowly	Water inlet valve	Valve 154637401
Dishes not drying well	Heating circuit components	Heater 154665201

Why it matters

Kenmore dishwashers are designed for years of dependable operation, and most performance issues come down to a few serviceable components (door seals, hoses, valves, and pumps). Using the correct model-specific part helps prevent repeat leaks, poor cleaning, and installation fit problems.

Installation and fit tips (especially after replacing hoses)

The installation instructions highlight common causes of post-repair problems.

• Avoid kinking the water or drain hose
• Flush the water line before final connection to help protect the inlet screen
• Confirm you have a 120V, 15 to 20 amp grounded supply
• Level the dishwasher for best sound and performance
• Anchor the dishwasher properly after reinstalling

For connection and anchoring details, follow the 58715194400 installation guide.

Last updated: February 2026

Yes; repairing your Kenmore dishwasher model 58715194400 is worth it when the failure is a leak, drain problem, or other wear item and the total repair cost stays reasonable. Replacement makes more sense when you have repeated breakdowns or a high-cost control or motor repair.

How we decide: age, cost, and what failed

Use these checkpoints before buying parts or scheduling service:

• Age: under 10 years old favors repair; over 10 years old depends on overall condition.
• Failure type: seals, hoses, and valves are usually cost-effective; electronics and motors cost more.
• Symptom count: one clear issue (single leak point, won’t drain) favors repair; multiple symptoms favor replacement.
• Leak source: confirm whether the leak is at the door, sump, or plumbing connections.

Repairs that are usually worth it on model 58715194400

These are common fixes that often restore normal operation:

• Door-area leak: replace a torn or flattened lower door seal such as the gasket 809006501.
• Won’t drain or drains slowly: inspect for kinks or clogs and replace the hose 807117001 if needed.
• No fill or weak fill: verify the shutoff valve is open and replace the valve 154637401 if the inlet valve is failing.

When replacement starts to make sense

Compare the total repair (parts plus labor) to a new dishwasher when these are involved:

Repair area	What you may notice	Decision driver
Electronic control	No-start, erratic cycles	Part cost plus diagnosis time
Motor/pump	Loud operation, poor wash	Labor plus additional wear risk
Multiple leaks	Drips from more than one area	Parts list grows quickly

Why it matters

This dishwasher recirculates and filters wash water for cleaning performance; fixing leaks and drain or fill problems early prevents repeat failures and helps avoid water damage.

For model-specific care, checks, and component locations, use the 58715194400 owner’s manual.

Last updated: February 2026