Craftsman 113298844 10" contractor drive saw Parts

On the Craftsman 113298844 10-inch contractor drive saw, there typically is not a separate external “reset button” on the saw body. The reset is usually part of the motor overload protector or the switch, and it’s commonly located on or near the motor housing (sometimes behind a small cap or cover).

• Unplug the saw before touching the motor, switch, or wiring.
• Let the motor cool 15 to 30 minutes if it tripped during a heavy cut.
• Look on the motor end bell and around the motor housing for a small reset access (cap, plug, or button).
• Check the ON/OFF switch area for a built-in overload reset (some versions integrate it there).
• Reduce load before restarting: sharp blade, correct blade type, proper feed rate, and aligned fence.

Most Craftsman contractor-style table saws use one of these overload reset styles:

A tripped overload is a protection feature. If you keep resetting without fixing the cause, you can overheat the motor, damage the switch, or create unsafe cutting conditions. The most common causes are a dull blade, binding wood, misalignment, or a failing motor capacitor.

• Verify the blade spins freely by hand (unplugged) and nothing rubs.
• Confirm the blade is sharp and appropriate for the material.
• Check extension cord use; long or undersized cords can cause voltage drop.
• Inspect the power cord and internal leads for damage; use a meter if needed (see how to use a multimeter to test electrical parts video).

Last updated: February 2026

For the Craftsman 113298844 10" contractor drive saw, the main parts are the blade-cutting system, the drive system, and the safety and control components that keep the cut accurate and your hands positioned safely. For a quick overview of common components, use our easy diy appliance repairs that anyone can do guide as a general DIY reference.

Most contractor-style table saws like the Craftsman 113298844 are built around these core assemblies:

• Table and base: tabletop work surface, extension wings, stand or cabinet
• Blade and arbor assembly: saw blade, arbor shaft, arbor bearings, arbor nut and flange
• Elevation and tilt mechanism: handwheels, trunnions, gears, tilt lock, height lock
• Drive system: motor, belt (or direct drive on some designs), pulleys, belt guard
• Rip fence and miter system: rip fence, rails, miter gauge, miter slots
• Safety parts: blade guard, splitter or riving knife (design varies by age), anti-kickback pawls, throat plate
• Dust management: dust port or shroud (varies), internal deflectors

Knowing the main parts helps you troubleshoot faster. For example, burn marks often point to fence alignment or a dull blade, while excess vibration often points to the arbor, pulleys, or belt.

• Unplug the saw before any inspection or adjustment
• Remove the throat plate to check for debris around the blade and arbor
• Confirm the blade is tight and installed correctly
• Verify the fence locks parallel to the blade
• Check belt tension and pulley set screws (if belt-driven)

Last updated: February 2026

For the Craftsman 113298844 10-inch contractor drive saw, the motor “size” is identified on the motor nameplate (HP, amps, volts, and RPM). For many 10-inch contractor-style table saws, you’ll commonly see a belt-drive induction motor rated around 1 to 2 HP, often 120V or dual-voltage (120/240V).

Use the motor’s nameplate as the deciding source; it reflects the exact motor currently installed.

• Horsepower (HP): the primary “motor size” rating
• Amps (A): current draw at the rated voltage
• Voltage (V): 120V, 240V, or dual-voltage
• RPM: motor speed (not the same as blade speed)
• Frame and shaft details: helpful when matching a replacement motor or pulley

1. Unplug the saw.
2. Locate the motor nameplate (usually on the side of the motor housing).
3. Write down HP, amps, volts, RPM, and any catalog/model number on the motor.
4. If the plate is dirty, wipe it clean and take a photo for reference.

These are common ranges for 10-inch contractor-drive table saws; your 113298844 may be different depending on the motor installed.

Using the exact nameplate rating helps you choose the right circuit, extension cord gauge, and replacement motor components (pulley, belt, switch) so the saw starts reliably and holds speed in thicker stock.

If you need help confirming you’re looking at the correct identification label for parts lookup, use how to find your appliance model number (and what it means for parts).

Last updated: February 2026

Craftsman model 113298844 is a 10-inch contractor drive saw (table saw), so it uses a 10-inch circular saw blade, not a band saw blade length. If you have a Craftsman 12-inch band saw, the blade length is set by the band saw’s exact model number and must match that machine.

• 113298844: 10-inch table saw; uses a 10-inch blade (diameter matters)
• 12-inch band saw: uses a loop blade (length matters)
• Check the model tag on the tool’s frame or base and match the full number
• Look inside the band saw wheel cover for a blade-length decal
• If you still have the old band saw blade, measure the full loop length

Use the exact blade length your 12-inch band saw specifies; then choose width and TPI for the work.

A band saw blade that is even slightly off in length will not tension or track correctly; that causes drift, poor cut quality, and premature blade breakage.

• How to find your appliance model number (and what it means for parts)

Last updated: February 2026