Owner’s manual
Error Codes
How do you reset the F2 E2 on a Kenmore dishwasher?
On Kenmore Elite dishwasher model 66513189K802, we reset an F2 E2 (user interface communication/keypad issue) by doing a control reset: press CANCEL/DRAIN twice to reset the control, then press START/RESUME to restart a cycle (as outlined in the 66513189K802 owner's manual).
- Open the door slightly to stop the cycle; wait for spraying to stop.
- Press CANCEL/DRAIN twice to reset the control.
- Close the door.
- Select a new cycle and options.
- Press START/RESUME and firmly close the door within 3 seconds.
F2 E2 often shows up when the keypad is not being read correctly or the control is not seeing the user interface.
- Make sure Control Lock is off; on many Kenmore models you press and hold HEATED DRY for 4 seconds.
- Power reset: turn the dishwasher breaker off for 1 minute, then back on.
- Check for stuck keys: wipe the console and press each key once to confirm none feel jammed.
- If the unit drains but will not start, focus on the control and console inputs.
| What you see | What it usually means | What to do next |
|---|---|---|
| Buttons beep but cycle will not start | Control lock on or door not latched | Turn off lock, re-close door, press START/RESUME |
| No response from most keys | Keypad/user interface issue | Do CANCEL/DRAIN reset, then power reset |
| Error returns quickly after reset | Ongoing communication fault | Inspect wiring connections; consider control repair |
Resetting clears a “latched” control state so the dishwasher can re-check the door switch, keypad inputs, and cycle logic. If the error returns, it points to an input or control communication problem rather than a one-time glitch.
Last updated: January 2026
What does E15 mean on a Kenmore dishwasher?
On the Kenmore Elite dishwasher model 66513189K802, an E15 code points to a leak protection condition: water has collected in the bottom/base area and a float or leak sensor has been triggered, so the dishwasher may stop or run the drain pump to prevent overflow. See the 66513189K802 owner's manual for safety and troubleshooting guidance.
- Turn off power at the breaker, then turn off the water supply valve.
- Pull the toe-kick panel and look for water in the base pan area.
- If you find water, dry it out (towels or a wet/dry vacuum), then run a short cycle and watch for the source.
- Check the door perimeter for gaps, folds, or debris on the seal.
- Inspect the drain hose routing for kinks and loose connections.
- Door not sealing due to food debris or a damaged door seal
- Oversudsing from the wrong detergent or too much detergent
- Leak at the drain hose connection or a split hose
- Water inlet valve seepage or loose fill connection
- Internal leak from the sump, spray system, or pump area
| Symptom you see | Likely area to inspect | Example part for this model |
|---|---|---|
| Water under door | Door sealing surface | Dishwasher door seal W11196317 |
| Water near sink cabinet side | Drain connection/hose | Dishwasher drain hose 8269144A |
| Unit keeps trying to drain | Base pan wet, leak switch active | Dishwasher drain pump WPW10348269 |
E15 is the dishwasher protecting your kitchen from flooding. Clearing the water and fixing the leak source prevents repeat shutdowns, protects the electronic control, and helps the wash system run normally.
Last updated: January 2026
What is the average lifespan of 66513189K802?
The average lifespan of the Kenmore Elite dishwasher model 66513189K802 is 10 years with normal use and routine maintenance (especially keeping the filter and spray system clean). For model-specific care steps and cleaning intervals, use the owner's manual.
A dishwasher’s service life is driven by heat, water quality, and how clean the wash system stays. These items make the biggest difference:
- Filter maintenance; a clogged filter strains the pump and reduces cleaning performance
- Hard water scale; mineral buildup can restrict spray and affect heating
- Drain performance; slow draining leaves soil behind and can stress the drain pump
- Loading habits; blocking the spray arm reduces wash action and increases rewash cycles
- Leaks at the door; moisture where it should not be can damage components over time
The manual for this platform includes a filter-cleaning frequency chart; using it keeps the sump and pump area clearer.
| Maintenance item | Typical interval | Why it matters |
|---|---|---|
| Clean dishwasher filter | Monthly (hard water) or every 2 to 12 months (normal use) | Protects pump, improves cleaning |
| Check spray arm holes | Monthly | Prevents weak spray and poor coverage |
| Run a cleaning cycle | Monthly | Reduces grease and mineral buildup |
| Inspect door seal | Every 3 to 6 months | Helps prevent leaks |
If performance drops, these are frequent wear or failure points on many Kenmore dishwashers of this design:
- Dishwasher filter W10872845 (helps keep food and debris out of the pump)
- Dishwasher drain pump WPW10348269 (moves water out during drain)
- Dishwasher water inlet valve W10648041 (controls fill water into the tub)
- Dishwasher door seal W11196317 (helps prevent leaks around the door)
Planning around a 10-year lifespan helps you decide whether to maintain, repair, or refresh key components like the filter, drain system, and door sealing surfaces before they cause bigger performance problems.
Last updated: March 2026
