Kenmore Elite 79572063111 refrigerator Parts

For Kenmore Elite refrigerator model 79572063111, the correct water filter is the Refrigerator water filter 9690; on our parts list it’s part ID AGF80300801 (manufacturer part number ADQ36006102). This is the filter that fits your model and restores proper water and ice filtration.

Use these quick checks before ordering:

• Match your refrigerator model number exactly: 79572063111
• Match the filter ID on the listing: AGF80300801
• Replace on schedule (most refrigerator filters are changed about every 6 months)
• Flush the new filter after install (dispense several gallons of water until it runs clear)
• Reset the filter indicator light (if your model has one)

For model-specific filter location and reset steps, use the 79572063111 owner's manual.

Using the correct filter helps protect the water inlet valve, ice maker, and dispenser tubing from sediment buildup, and it keeps water taste and odor under control. A mismatched filter can leak, restrict flow, or fail to seat correctly.

• Turn the filter clockwise until it fully seats (do not force it)
• Check the filter head and O-ring area for debris before installing
• If water flow is weak, confirm household supply is fully open and the filter is seated
• If the dispenser sputters, keep dispensing water until air is purged

For step-by-step guidance, see how to replace the water filter in a Kenmore refrigerator.

Last updated: January 2026

Kenmore Elite refrigerator model 79572063111 is a bottom-mount style refrigerator; most units in this class are about 33 inches wide, 30 to 34 inches deep, and 67 to 70 inches tall. For the exact cabinet dimensions and clearance requirements, use the 79572063111 owner's manual.

When you are checking fit for a kitchen opening, we recommend measuring the refrigerator and the space in three ways:

• Width: cabinet width (not including door handles unless they stick out past the cabinet)
• Depth: cabinet depth and depth with doors closed (depth can change a lot with handles)
• Height: cabinet height and height with hinges
• Door swing clearance: space needed to fully open doors and pull out drawers
• Ventilation clearance: space behind, above, and at the sides for airflow

Use this checklist to avoid common “it won’t fit” surprises:

• Measure the narrowest point on the path in (doorways, hallways, turns)
• Confirm the floor is level where the refrigerator will sit
• Plan for water line routing if you use the ice maker or water dispenser
• Allow extra depth if you need the doors to open past 90 degrees
• Verify the opening allows the freezer drawer to pull out fully

These are typical ranges for Kenmore bottom-mount refrigerators similar to model 79572063111.

Correct sizing prevents door interference, poor ventilation (which can affect cooling and compressor run time), and installation issues with the water line. It also helps you plan for replacing parts like a door gasket or door bin without clearance problems.

Last updated: January 2026

On Kenmore Elite model 79572063111, dH (often shown as Er dH) points to a defrost heating problem: the refrigerator is not sensing the expected temperature rise during the defrost cycle. This can lead to frost buildup, warm temperatures, and poor airflow.

• Power reset: unplug for 5 minutes, then restore power and watch for the code returning.
• Door sealing and loading: make sure doors close fully and vents are not blocked by food.
• Frost pattern: heavy frost on the freezer back panel usually supports a defrost issue.
• Condenser cleanliness: clean dust from the condenser area to reduce run time and icing risk.
• Temperature settings: set freezer near 0°F and fresh food near 37°F, then allow 24 hours to stabilize.

For this model, a common service part related to defrost sensing is the refrigerator defrost sensor assembly 6615JB2005R.

When defrost heat is not working correctly, ice can block airflow across the evaporator. That forces longer compressor run times, causes temperature swings, and can stop the ice maker from producing normally.

Use the 79572063111 owner's manual for the control panel behavior, error display details, and any built-in test modes that apply to your exact configuration. For code interpretation help, we also use the Kenmore 795 model bottom freezer refrigerator error codes reference.

Last updated: January 2026

On Kenmore Elite refrigerator model 79572063111, an ice maker usually stops making ice because the freezer is too warm, the ice maker is switched off, water supply is restricted (often by a clogged filter), or the ice maker cannot sense the bin or door correctly. Use the 79572063111 owner's manual to confirm the exact control settings and test steps for your unit.

• Confirm the ice maker is ON (some models have an on/off switch or arm).
• Set freezer temperature to about 0°F (ice production drops fast above ~10°F).
• Make sure the ice bin is seated correctly and not jammed with clumped ice.
• Verify the household shutoff valve is fully open and the supply line is not kinked.
• Replace a restricted water filter such as genuine Kenmore refrigerator water filter 9690 AGF80300801 if water flow is slow.

1. Check freezer cooling first: If food is soft or ice cream is mushy, solve the cooling issue before chasing the ice maker.
2. Check water flow at the dispenser (if equipped): Weak flow points to a filter restriction or supply issue.
3. Inspect the fill area: Look for ice blocking the fill tube or signs of a slow drip that freezes up.
4. Door and bin sensing: If the door is not registering as closed, the ice maker may pause; a failed switch can be the cause.

The ice maker depends on two basics: proper freezer temperature and steady water flow. Fixing those first prevents unnecessary part replacement and restores normal ice production faster.

Last updated: January 2026