Kenmore Elite 66513133K701 dishwasher Parts

To identify your Kenmore Elite dishwasher model, open the door and look for the model/serial label on the inner door frame or along the tub opening. For this parts page, the correct model number format looks like 66513133K701; confirm it on the label before ordering parts.

Where to look on the dishwasher

Check these common label locations first (in this order):

• Along the left or right inner door frame (door jamb area)
• On the top rim of the tub opening (visible with the door open)
• On the side wall of the tub near the front (left or right)
• Behind the lower access panel area (less common)

If the label is faded, use a flashlight and look for lightly printed characters.

What the model number should look like

Kenmore dishwashers typically use a 3-digit prefix followed by more characters. For this Kenmore Elite model page, you are looking for:

Item	Example for this model	Why it matters
Model number	66513133K701	Ensures correct fit for parts like a drain pump or spray arm
Serial number	(varies)	Helps identify production run details for service

Tips to avoid ordering the wrong part

Before you buy a replacement part, we recommend these quick checks:

• Match the entire model number, including the ending letters/numbers (for example, K701)
• Write it down exactly as shown; do not drop leading zeros
• Use the model number when selecting parts such as the dishwasher drain pump WPW10348269
• Keep the model number handy when following setup steps in the 66513133K701 installation guide

Why it matters

Kenmore Elite dishwashers in the 665 series can look similar across multiple revisions, but internal components (like the electronic control, drain hose routing, and rack hardware) can differ by model suffix. Using the exact model number helps us match the correct parts and troubleshooting info.

Last updated: January 2026

To add rinse aid in your Kenmore Elite dishwasher model 66513133K701, open the rinse aid dispenser, fill it to the FULL indicator (about 5 oz total capacity), then lock the cap back in place. Rinse aid improves drying and helps prevent spots and streaks.

Steps to fill the rinse aid dispenser

• Open the dishwasher door fully so the fill indicator reads correctly.
• Locate the rinse aid dispenser cap on the inside of the door.
• Turn the cap/knob to REFILL and remove it.
• Pour liquid rinse aid into the opening until the indicator points to FULL (do not overfill).
• Wipe up any spilled rinse aid to prevent excessive suds.
• Reinstall the cap and turn it to LOCK.

For the exact dispenser location and illustrations for this model, use the 66513133K701 owner's manual.

Adjusting the rinse aid setting (if you see spots)

Your dispenser is adjustable. The factory setting is typically 2, which works well for most homes.

• Turn the knob to REFILL and remove it.
• Turn the arrow inside the dispenser to the desired setting.
• Reinstall the knob and turn it to LOCK.
• Increase the setting if you have hard water and see calcium buildup or spotting.
• Decrease the setting if you notice foaming or streaking.

Quick guide: what setting changes usually do

What you notice on dishes	Typical adjustment	Why
Spots or white film	Increase setting	More rinse aid helps water sheet off
Streaks or foamy residue	Decrease setting	Too much rinse aid can cause suds
Poor drying	Use rinse aid plus Heated Dry	Improves water drainage and evaporation

Why it matters

Rinse aid is essential for good drying performance on high-efficiency dishwashers. It helps water drain off dishes during the final rinse so you get fewer droplets that dry into spots.

Last updated: January 2026

On Kenmore Elite dishwasher model 66513133K701, the F4E1 code points to a wash motor or wash pump problem (the dishwasher is not circulating water correctly). This typically shows up as poor cleaning, little spray action, or a cycle that stops and drains.

What to check first (fast, no parts)

• Cancel the cycle and let the unit drain; then restart a normal cycle.
• Confirm the water supply valve is fully open and the fill is normal.
• Make sure the spray arms spin freely and are not blocked by tall items.
• Clean the filter area so water can circulate properly.
• Power reset: turn off the breaker for 1 minute, then restore power.

Likely causes and what they look like

Symptom	Most likely cause	What you can do
Dishes stay dirty, little spray noise	Wash motor not running	Listen for a steady wash sound after filling; if silent, motor circuit is suspect
Intermittent washing, stops mid-cycle	Motor overheating or control sensing a fault	Reset power; check for binding in spray arms and filter area
Unit drains but never really washes	Circulation issue in sump area	Clean filter and check for debris; inspect for obstructions

Parts that commonly relate to circulation and draining

F4E1 is a wash-side fault, but these related components are often checked during diagnosis:

• Dishwasher drain pump WPW10348269 (draining performance can mask wash issues)
• Filter W10872845 (restricted flow reduces spray pressure)
• Dishwasher spray arm WPW10491331 (clogs or damage reduce circulation)

Why it matters

When the dishwasher cannot circulate water at the right pressure, detergent does not dissolve correctly and soil is not removed. Continuing to run cycles with a circulation fault can lead to repeated error codes and poor results.

Helpful reference

• Use the troubleshooting and reset guidance in the 66513133K701 owner's manual.
• If your display shows additional codes with F4E1, match them using Kenmore 665 model dishwasher error codes.

Last updated: January 2026

To hard reset (reset the control) on Kenmore Elite dishwasher model 66513133K701, we use the built-in cancel/reset sequence: stop the cycle, then press CANCEL/DRAIN twice to clear the control so you can select a new cycle. See the steps in the 66513133K701 owner's manual.

Steps to reset the control (hard reset)

1. Open the door slightly to pause the cycle; wait for spraying to stop.
2. Open the door fully.
3. Press CANCEL/DRAIN twice to reset the control.
4. Select the new cycle and any options.
5. Press START/RESUME and firmly close the door within 3 seconds.

If you only need to cancel and drain

Use this when the dishwasher is running and you just want it to stop and pump out water.

• Open the door slightly; wait for spraying to stop.
• Press CANCEL/DRAIN once.
• Close the door within 3 seconds.
• Let the drain cycle finish (the Cancel/Drain light turns off after about 2 minutes).

If the buttons do not respond (Control Lock)

Control Lock disables the keypad but still lets you open and close the door.

• Press and hold HEATED DRY for 3 seconds to turn Lock on or off.
• When LOCK ON is lit, the dishwasher cannot run.
• If you press a pad while locked, the indicator flashes.

Quick reference

What you want to do	Buttons	What happens
Cancel and drain	CANCEL/DRAIN once	Drains (if water is present), then stops
Reset the control	CANCEL/DRAIN twice	Clears the cycle so you can reselect
Unlock controls	HEATED DRY (hold 3 sec)	LOCK ON toggles on/off

Why it matters

Using the correct reset sequence clears a stuck cycle and restores normal operation without guessing button combinations; it is also the fastest way to recover from a blinking Clean light or an interrupted cycle.

Last updated: January 2026