Kenmore 10658136700 refrigerator Parts

For your Kenmore 10658136700 side-by-side refrigerator, the most reliable way to confirm cubic feet is to read the model’s rating plate inside the fresh food compartment; it typically lists the refrigerator’s total volume (capacity) in cubic feet. Use the owner's manual to help locate the rating plate and interpret the label.

Check these common spots inside the refrigerator section:

• On an interior side wall (often upper right or left)
• Behind or beside the crisper drawers
• On the ceiling of the fresh food compartment
• Near the door hinge area (inside the cabinet)
• Occasionally behind a removable trim piece near the bottom front

You can estimate capacity by measuring the usable interior space and converting to cubic feet.

• Measure width, height, and depth (in inches) of the main interior cavity
• Multiply: width x height x depth = cubic inches
• Divide by 1,728 to convert cubic inches to cubic feet
• Subtract a little for shelves, bins, and air channels (they reduce usable space)

Most Kenmore side-by-side refrigerators fall in this range:

• About 20 to 26 cubic feet total
• Freezer is commonly about 1/3 of total capacity
• Fresh food section is commonly about 2/3 of total capacity

Knowing cubic feet helps us match the right replacement parts and accessories (like shelves, bins, and water filtration) and it also helps when comparing energy use and storage needs. If you are servicing the water system, the correct filter matters; this model uses the genuine Kenmore refrigerator water filter EDR3RXD1.

Last updated: February 2026

To replace the ice maker in your Kenmore 10658136700 side-by-side refrigerator, we disconnect power first, remove the ice bin and mounting screws, swap the ice maker assembly, then restore power and confirm the wire shutoff arm is lowered so ice production can resume. See the 10658136700 owner's manual for model-specific safety notes.

• Unplug the refrigerator or switch off the circuit breaker.
• Turn off the water supply to the refrigerator if you will disconnect the water line.
• Use two people if you need to move the refrigerator for access.
• Keep screws and brackets organized so the new ice maker mounts securely.
• Restore all covers and panels before operating.

1. Remove the ice storage bin/container from the freezer door or freezer compartment.
2. Remove the ice maker cover (if equipped) and unplug the ice maker wiring harness.
3. Remove the mounting screws, then lift the ice maker off its mounting tabs/bracket.
4. Transfer any reusable parts from the old unit to the new one if they match exactly (for example, a wire shutoff arm or mounting bracket, if included on your design).
5. Install the new ice maker onto the mounting tabs, reinstall screws, and reconnect the wiring harness.
6. Reinstall the ice bin.
7. Restore power.

Your model uses a wire shutoff arm as the On/Off control.

• ON: wire shutoff arm down
• OFF: wire shutoff arm up

A loose mount, a disconnected harness, or leaving the wire shutoff arm in the OFF position can stop ice production even when the new ice maker is installed correctly.

Last updated: February 2026

On Kenmore model 10658136700 side-by-side refrigerators, we typically find the model number on the appliance identification label inside the fresh food (refrigerator) compartment, most often along a side wall near the crisper area or around the door opening. Use the placement diagrams and label examples in the 10658136700 owner's manual to confirm the exact spot.

• Inside the refrigerator compartment on the left or right side wall
• Around the door opening (door jamb area) near the gasket
• On the ceiling of the fresh food compartment near the control housing
• Behind the crisper drawers (you may need to slide drawers out)
• On the back exterior panel (less common, but worth a quick look)

The ID label usually includes both a model number and a serial number. For parts lookup and diagrams, the model number is the key.

• Use a flashlight; labels are often printed in small text.
• Wipe condensation or residue off the label so every digit is readable.
• Copy the model number exactly as shown (all digits, no spaces).
• If the label is inside the compartment, check both the refrigerator and freezer sides.

Kenmore side-by-side refrigerators can look similar across multiple model series. Using the exact model number helps us match the correct shelves, water filter, ice maker, and other refrigerator parts for your unit.

Last updated: February 2026

Water leaking from the bottom of your Kenmore 10658136700 side-by-side refrigerator is usually caused by a defrost drain that’s clogged or frozen, so meltwater can’t reach the drain pan and instead overflows onto the floor. We use the steps in the owner's manual to confirm normal defrost water flow and rule out a water-supply leak.

• Clogged defrost drain: Water backs up and leaks out near the front.
• Frozen drain opening: Ice blocks the drain so defrost water spills into the cabinet.
• Drain pan shifted or cracked: Defrost water misses the pan.
• Water line or valve seep: Slow leak from the supply connection or valve.
• Ice maker fill issue: Overfill or splash can mimic a drain problem.

1. Unplug the refrigerator (or switch off power).
2. Check for ice or standing water on the freezer floor or under crisper drawers.
3. Clear the defrost drain:
   • Flush the drain hole with hot (not boiling) water.
   • Melt visible ice with a hair dryer on low (keep heat moving).
   • Feed a flexible plastic tube or pipe cleaner into the drain to remove sludge.
4. Inspect the drain pan underneath for cracks and make sure it’s centered.
5. If the leak appears tied to the dispenser or ice maker, inspect the water inlet valve and fittings; a failing valve can seep and drip down the back. If needed, replace the refrigerator water inlet valve W10408179.

A blocked drain can refreeze into a larger ice buildup, restrict airflow, and create recurring puddles. A slow water-supply seep can damage flooring and lead to intermittent ice maker or dispenser performance.

Last updated: February 2026