Kenmore 10657285790 refrigerator Parts

To replace the ice maker in your Kenmore 10657285790 side-by-side refrigerator, we shut off power and water, remove the ice bin and old ice maker, install the replacement assembly, then flush the water system and allow up to 24 hours for ice production (discard the first three batches). Use the 10657285790 owner's manual for model-specific safety notes.

Before you start

• Unplug the refrigerator or disconnect power.
• Turn the ice maker OFF by lifting the signal arm.
• Shut off the household water supply.
• Keep a towel handy for small spills.
• Use a screwdriver or nut driver and save all screws.

Replace the ice maker (typical steps)

1. Pull out the ice container to access the ice maker.
2. Disconnect the ice maker wiring harness.
3. Remove mounting screws; lift the ice maker out.
4. Install the new unit; tighten screws and reconnect wiring.
5. Restore water and power; lower the signal arm to turn the ice maker ON.

If you are replacing the complete unit for this model, use the ice maker assembly - refrigerator ice maker by whirlpool 4317943.

After installation: flush and startup timing

• Dispense and discard 2 to 3 gallons of water (about 6 to 7 minutes).
• Wait 24 hours for the first ice.
• Discard the first three batches of ice.

What you see	What it usually means	What we do
No ice right away	Normal startup	Wait 24 hours
No ice after 24 hours	Ice maker OFF or water off	Arm down; valve open
Jam at ejector	Cube stuck	Clear with plastic utensil

Why it matters

Flushing clears air and residue from the water line, and the 24-hour wait prevents mistaking normal startup time for an ice maker problem.

Last updated: February 2026

The exact cabinet dimensions for Kenmore model 10657285790 are listed in the owner's manual. For planning space, we use the manual’s clearance requirements: allow 1/2 inch on each side and at the top, plus 2 inches minimum next to a fixed wall for door swing.

What you can measure now (quick, accurate method)

Use a tape measure and record these three numbers:

• Width: left outside edge to right outside edge (doors closed)
• Height: floor to top of cabinet (include hinge cover if it sits higher)
• Depth: back to front (note two depths: cabinet only, and to the front of handles)

Tip: Measure twice, then compare to the spec section in the owner's manual so your cutout and door-swing plan match the refrigerator.

Space and clearance requirements (from the manual)

These clearances matter as much as the refrigerator’s dimensions because they affect airflow and door opening:

• 1/2 inch (1.25 cm) on each side
• 1/2 inch (1.25 cm) at the top
• Extra space behind if an ice maker water line is connected
• 2 inches (5.08 cm) minimum next to a fixed wall (varies by setup) for door swing

Planning guide (dimensions vs. clearances)

What you’re planning for	What to use	Why it matters
Cabinet fit between walls	Measured width + side clearances	Prevents rubbing and improves ventilation
Fit under cabinets	Measured height + top clearance	Avoids heat buildup and vibration noise
Walkway and door swing	Depth (to handles) + 2-inch wall clearance	Ensures doors open fully and bins slide out
Ice maker hookup	Extra rear space	Prevents kinks and leaks in the water line

Why it matters

A side-by-side refrigerator like the Kenmore 10657285790 needs proper airflow and door swing room to cool correctly, avoid condensation, and keep the ice maker and dispenser working reliably.

Last updated: February 2026

On Kenmore model 10657285790 side-by-side refrigerators, the model and serial number label is typically on the inside of the fresh food (refrigerator) compartment, on a side wall. The owner's manual shows this label location in the Parts and Features section.

Quick ways to find the label

• Open the refrigerator (fresh food) door and check the left and right interior side walls
• Look near the crisper drawers and the meat pan area (lower side wall)
• Check behind or near the control panel area inside the compartment (varies by configuration)
• If shelves or bins block your view, slide them out for a clear look
• Use a flashlight; the label is often small and low-contrast

What you should see on the tag

The label lists both identifiers. Use the model number when ordering parts like an ice maker, thermostat, or door gasket.

Item on label	What it’s used for	Example format
Model number	Matching the correct parts list	10657285790
Serial number	Identifying production details	Letters and numbers

Why it matters

Kenmore side-by-side refrigerators can look similar across multiple model series. Using the exact model number helps us match the correct diagrams and parts (for example, an ice maker assembly - refrigerator ice maker by whirlpool 4317943) so the replacement fits and functions correctly.

Last updated: February 2026