Kenmore Elite 79579044310 refrigerator Parts

Common problems on the Kenmore Elite refrigerator model 79579044310 include warm temperatures (airflow or sealed-system issues), frost buildup (defrost or door-seal problems), water leaks (drain or water-supply issues), and unusual noises (fan or compressor-related). We use the symptoms to narrow the likely failed part and the safest next step.

Most common symptoms and what usually causes them

• Not cooling or weak cooling: dirty condenser coil, failed evaporator fan motor, or compressor/start components
• Frost or ice buildup (freezer or back wall): defrost sensor/heater issues, door left ajar, or poor door seal
• Water leaking or puddles: clogged defrost drain, cracked drain pan, or water line/valve seepage
• Ice maker not making ice: water supply restriction, inlet valve problem, or ice maker assembly failure
• Clicking, buzzing, or rattling: fan blade hitting ice, failing compressor, or electrical overload protection cycling

For model-specific operating checks and control settings, follow the troubleshooting steps in the 79579044310 owner’s manual.

Quick checks we recommend before replacing parts

1. Confirm temps: refrigerator about 37°F, freezer about 0°F.
2. Clean the condenser area (unplug first); restricted airflow is a top cause of warm temps.
3. Make sure vents inside are not blocked by food packages.
4. Check door closure: bins and drawers should not prevent a full seal.
5. If you hear a fan noise change when you open the door, the door switch may be involved.

Parts that commonly fix these problems on 79579044310

Symptom	Common suspect part	Example part for this model
Warm temps, poor airflow	Evaporator fan motor	Lg refrigerator evaporator fan motor 4681JB1027C
No ice or slow fill	Water inlet valve	Lg refrigerator water inlet valve AJU73753101
Clicking with no start	Compressor overload protection	Refrigerator compressor overload protector 6750CL0001D
Frost/defrost issues	Defrost sensor assembly	Refrigerator defrost sensor assembly 6615JB2005N

Error codes (when the display shows a code)

If your Kenmore Elite 795 model shows an error code, use the code to pinpoint the circuit or sensor involved before ordering parts; see Kenmore 795 model bottom freezer refrigerator error codes.

Why it matters

Catching airflow, defrost, and water-supply problems early helps protect food, reduces compressor run time, and prevents repeat icing or leaking that can damage shelves, drawers, and wiring.

Last updated: January 2026

On Kenmore Elite refrigerator model 79579044310, warm temperatures in the lower (fresh food) section usually happen when airflow is blocked or the cooling system cannot move heat out efficiently. Start with simple checks like condenser coil cleaning and verifying the evaporator fan is running; then move to sensors and sealed-system components.

Quick checks we recommend first

• Set temperatures to typical targets: 37°F for the refrigerator and 0°F for the freezer.
• Make sure vents inside the refrigerator are not blocked by food containers.
• Confirm the doors close fully and the gaskets seal all the way around.
• Clean dust and pet hair from the condenser area (often underneath or behind the unit).
• Check for heavy frost on the freezer back panel (a defrost problem can choke airflow).

Most common causes (and what to look for)

What you notice	Likely cause	What to do next
Freezer is cold but refrigerator bottom is warm	Restricted airflow or evaporator fan issue	Listen for the fan; clear vents; inspect for frost buildup
Both sections are warming	Dirty condenser, condenser fan issue, or compressor problem	Clean coils; verify fans; check for steady compressor operation
Temps swing up and down	Sensor or control issue	Inspect wiring connections; consider sensor or control diagnostics

Parts that commonly relate to this symptom

If basic airflow and cleaning steps do not restore cooling, these model-matched parts are often involved:

• Lg refrigerator evaporator fan motor 4681JB1027C: moves cold air from the evaporator into the refrigerator section.
• Refrigerator temperature sensor 6500JB2002X: reports compartment temperature to the control.
• Refrigerator electronic control board CSP30020817: manages compressor and fan run times.
• Refrigerator compressor TCA38091801: the heart of the sealed system; weak operation can reduce cooling everywhere.

Why it matters

When the bottom of the refrigerator stays warm, food safety and freshness are affected first. Fixing airflow restrictions early also prevents longer run times that can stress the compressor and increase energy use.

Model-specific guidance

Use the 79579044310 manual for the exact vent locations, temperature setting recommendations, and any diagnostic steps specific to this Kenmore Elite bottom-mount design.

Last updated: January 2026

On Kenmore Elite refrigerator model 79579044310, dH (often shown as Er dH) points to a defrost heating problem. It typically means the refrigerator is not sensing the expected temperature rise during defrost, so frost can build up and airflow can drop.

What you may notice

• Freezer temperature slowly rises or swings
• Frost or ice buildup on the rear freezer panel
• Weak airflow into the fresh food section
• Evaporator fan noise changes (rubbing or louder)
• Water leaking or refreezing near the freezer floor after defrost attempts

Quick checks we recommend first

Before testing parts, do these simple items that commonly trigger a dH/Er dH condition:

• Make sure doors fully close and gaskets seal (warm air causes heavy frost)
• Confirm vents are not blocked by food packages
• Power reset: unplug for 5 minutes, then restore power and monitor
• If the freezer back wall is heavily frosted, plan on a defrost-system check

What usually causes a dH/Er dH code

In most Kenmore 795 bottom-mount designs, the defrost system relies on a heater, sensors, and the main control to melt frost off the evaporator. A failure in any of these can trigger dH.

Likely cause	What it affects	Common symptom
Defrost sensor issue	Defrost temperature feedback	Frost returns quickly, code repeats
Heater circuit problem	Melting frost during defrost	Solid frost sheet on rear panel
Control board problem	Sends power to heater	Intermittent or persistent dH
Airflow restriction	Heat does not distribute well	Warm fresh food section

Parts that commonly relate to this issue on 79579044310

If troubleshooting points to a sensor or airflow problem, these model-matched parts are often involved:

• Refrigerator defrost sensor assembly 6615JB2005N (defrost temperature sensing)
• Lg refrigerator evaporator fan motor 4681JB1027C (moves cold air across the evaporator)

For wiring diagrams, test points, and any model-specific diagnostic steps, use the 79579044310 manual.

Why it matters

A defrost heating fault lets frost build up on the evaporator, which blocks airflow and forces longer run times. Fixing the root cause restores normal cooling, protects food temperatures, and reduces strain on the compressor.

Last updated: January 2026

Water leaking from the bottom of your Kenmore Elite refrigerator model 79579044310 is typically caused by a clogged or frozen defrost drain, a slow leak in the water supply line or dispenser tubing, or an ice maker fill overflow that runs down into the base. Use the 79579044310 owner's manual for access and safety steps.

Quick checks we recommend

• Look for ice or standing water under the freezer drawer (common with a blocked defrost drain).
• Check for drips right after using the water dispenser.
• Inspect the water line connection at the back for slow seepage.
• Look for water trails from the ice maker area into the freezer.
• Confirm doors seal and close fully; warm air can create excess frost that later melts.

Most common causes and fixes

Clogged or frozen defrost drain

Defrost water should flow to a drain pan; when the drain is blocked, water overflows to the bottom.

• Unplug the refrigerator.
• Remove the freezer drawer/bins to reach the drain area.
• Melt visible ice with warm air and flush the drain with hot water.
• Clear debris from the drain opening and tube.

Leaking inlet valve or tubing

A valve that seeps or a cracked line can drip and collect underneath.

• Check the rear lower area for wetness.
• Tighten fittings gently if loose.
• Replace the lg refrigerator water inlet valve AJU73753101 if it continues to seep.

Ice maker fill overflow

Overfilling can spill water that migrates to the bottom.

• Clear ice from the fill cup and chute.
• Replace the lg refrigerator ice maker assembly model AEQ72909603 if the mold or housing is cracked.

Symptom-to-cause guide

What you notice	Most likely cause	Best next step
Ice/water under freezer drawer	Defrost drain clogged/frozen	Defrost and flush drain
Puddle behind refrigerator	Water line or inlet valve leak	Inspect fittings; replace valve
Leak after dispensing water	Dispenser tubing or filter housing	Inspect tubing; reseat filter

Why it matters

Stopping the leak prevents floor damage and reduces ice buildup that can restrict airflow and cause warm refrigerator or freezer temperatures.

Last updated: January 2026