Kenmore 11064992301 dryer Parts

On the Kenmore dryer model 11064992301, the most common sign of a bad heating element is that the dryer runs and tumbles normally but produces little to no heat, so clothes stay damp or take much longer to dry. A hot, “electrical” odor or repeated breaker trips can also point to a heating problem.

Common symptoms you can notice

• Dryer tumbles but there is no heat on heated cycles
• Dry times suddenly get much longer (even with a clean lint screen)
• Heat is inconsistent (warm sometimes, cool other times)
• A burning smell during normal use (not just first-time use)
• The dryer’s breaker trips or a fuse blows during heating

Quick checks before replacing parts

Our installation checks for this style of electric dryer are a good first step:

• Make sure you are using a heated cycle, not an air/no-heat cycle
• Confirm the dryer is plugged into a grounded outlet and power is on
• Check for two fuses or two circuit breakers; both must be on for full heat
• After about 5 minutes on a full heat cycle, open the door and feel for heat
• If there is still no heat after power checks, stop and move to component testing

For cycle selection and care guidance, follow the 11064992301 owner’s manual.

Heating element vs. other common “no heat” causes

What you see	More likely cause	What to check next
Tumbles, no heat	Power supply issue (one leg out)	Both breakers/fuses, terminal connections
Tumbles, no heat	Thermal cut-off or high-limit issue	Overheating from restricted venting
Tumbles, weak heat	Airflow restriction	Lint screen, vent duct, outside hood
Tumbles, no heat	Heating element failure	Element continuity, visible coil damage

If you determine the element is failed, the correct replacement for this model is the dryer heating element WP3387747.

Why it matters

Running with low or no heat wastes energy and can mask airflow problems that overheat the heater circuit. Restoring proper heat and airflow helps protect components like the thermistor, thermal cut-off, and wiring.

Last updated: January 2026

On Kenmore dryer model 11064992301, a bad switch is usually confirmed when the dryer will not start even though power is available and the door is fully closed. We verify the switch by unplugging the dryer and checking the switch for continuity with a multimeter.

Quick checks before testing the switch

Many “bad switch” symptoms are actually power or control setup issues. Before you open the console, confirm these basics:

• The dryer is plugged into a grounded outlet and power is on.
• A cycle is selected and the control is in a running position.
• The PUSH TO START button is pressed firmly.
• The door is fully closed (a door switch issue can mimic a start switch problem).
• House fuses are good; many electric dryers use two fuses or breakers.

For model-specific operating steps and control descriptions, use the 11064992301 owner's manual.

How we test a dryer switch (continuity test)

Safety first: unplug the dryer (or shut off the breaker) before accessing wiring.

1. Disconnect power.
2. Access the switch (start switch or door switch, depending on what you are testing).
3. Pull the wires off the switch terminals (note positions or take a photo).
4. Set your multimeter to continuity or lowest ohms.
5. Test the switch:
   • Not pressed / OFF: should read open (no continuity).
   • Pressed / ON: should read closed (continuity, near 0 ohms).

What the readings mean

Test result	What it usually indicates	Next step
Always open	Switch contacts not closing	Replace the switch
Always closed	Switch contacts stuck closed	Replace the switch
Changes correctly	Switch is likely OK	Check power, timer/control, motor circuit

Related parts that can cause “won’t start” symptoms

If the switch tests good, these are common next suspects on a Kenmore dryer:

• Door switch (door not registering as closed)
• Timer contacts (cycle not sending power to the motor)
• Drive motor circuit issues
• Loose wire connection at the terminal block (power supply)

If the door is not consistently “clicking” closed, inspect the latch/strike; the strike 279570 is a common wear item.

Why it matters

A failed start or door switch prevents the motor circuit from energizing, so the dryer will appear completely dead even when the outlet has power. Confirming continuity avoids replacing good parts and speeds up the repair.

Last updated: January 2026

Yes. On Kenmore dryer model 11064992301, replacing the heating element is a common DIY repair if you’re comfortable using basic hand tools and following safety steps. The key is disconnecting power, documenting wire locations, and reassembling the heater housing exactly as it was.

Safety first (before you remove any panels)

• Unplug the dryer (or switch off the breaker) before servicing.
• Confirm the dryer is fully de-energized before touching wiring.
• Let the dryer cool completely if it was recently running.
• Take a clear photo of every wire connection before you remove it.
• Avoid bending or damaging the heater housing and nearby ducts.

For model-specific safety and service guidance, follow the 11064992301 owner's manual.

What the job typically involves

Most electric dryers like this Kenmore use a heater assembly that can be removed and swapped without special tools.

• Remove the appropriate access panel to reach the heater housing.
• Label and disconnect wires from the heater terminals.
• Remove mounting screws and slide out the heater assembly.
• Transfer any sensors mounted to the housing (if present) to the replacement assembly.
• Reinstall the assembly, reconnect wires, and reassemble panels.

A common replacement part for this model is the dryer heating element WP3387747.

Quick checks after installation

After reassembly, we recommend verifying basic operation before running a full load.

Check	What you should see	If not
Drum runs	Motor turns and drum tumbles	Recheck door closure and wiring connections
Heat present	Warm air within about 5 minutes	Check both breakers/fuses and heater circuit parts
Airflow	Strong airflow at the outside vent hood	Clean/repair venting restrictions

Why it matters

A failed heating element is a top cause of “dryer runs but won’t heat,” but restricted airflow can also cause overheating and repeat heat failures. Keeping the lint screen and exhaust vent clear helps the new element last.

Last updated: January 2026

To hard reset your Kenmore dryer model 11064992301, unplug the power cord (or switch the breaker off) for 1 to 5 minutes, then restore power and try a cycle again. If it still will not run, the issue is usually power supply, door switch, or airflow related, not a reset.

Hard reset steps (safe and effective)

• Turn the Cycle Selector to OFF.
• Unplug the dryer (or turn both dryer breakers off, if applicable).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door firmly.
• Select a cycle and press PUSH TO START.

For control and cycle details specific to this dryer, use the 11064992301 owner's manual.

If the dryer still will not start after a reset

The manual’s troubleshooting for “dryer will not run” points to a few common checks:

• Confirm the dryer is plugged into a grounded outlet.
• Check house power; many dryers use 2 fuses or 2 circuit breakers, so verify both are on.
• Make sure the door is fully closed; a failed door switch can prevent starting.
• Verify the controls are set to a running position (not OFF).
• Press the Start button firmly.

Quick symptom-to-check table

What you see	Most likely check	What to do next
No lights, no response	Power supply	Check both breakers/fuses, outlet power
Lights on, won’t start	Door circuit	Inspect/replace dryer door switch WP3406107
Starts then stops quickly	Overheat protection/airflow	Clean lint screen and venting

Why it matters

A hard reset only clears a temporary control state. If the dryer is losing power, not sensing the door closed, or overheating from restricted venting, it will keep failing until the underlying cause is fixed.

Last updated: January 2026