Kenmore Elite 11087721700 dryer Parts

Yes. For the Kenmore Elite dryer model 11087721700, we can help you get compatible replacement parts such as the lint screen, drive belt, heating components, door hardware, and electrical connection parts. Use your model number to match parts correctly and avoid fit issues.

Parts we commonly replace on model 11087721700

These are examples of parts available for this exact Kenmore model:

• Dryer drive belt 661570V
• Dryer heating element WP8544771
• Dryer thermal fuse WP3392519
• Dryer idler pulley 279640
• Screen W10120998

How we make sure you get the right part

Even within the Kenmore 110 series, small design changes can affect fit. We recommend matching by the full model number 11087721700, then confirming the part ID on the listing.

• Confirm the full model number from the dryer’s model/serial label
• Compare the part name and part ID (not just a description like “belt”)
• If you are replacing a heating or safety part, inspect venting and airflow first
• For electrical connection items, match your 3-wire vs 4-wire setup

Quick examples: symptom to likely part

Symptom	Commonly involved part	What it affects
Dryer runs but no heat	Heating circuit parts	Drying temperature
Dryer won’t start	Door or start circuit parts	Motor start/run
Squealing or thumping	Drum support and belt drive parts	Drum rotation
Long dry times	Lint screen and venting	Airflow and moisture removal

Why it matters

Using parts that are verified for 11087721700 helps prevent repeat repairs, noise issues, overheating from restricted airflow, and installation problems. For operating and care tips that reduce wear on parts, see the 11087721700 use and care manual.

Last updated: January 2026

For Kenmore Elite dryer model 11087721700, the replacement cost depends on whether you’re paying for parts only (DIY) or parts plus labor (service). We can identify the correct heating element for this model, but labor pricing varies by provider and isn’t fixed to the model.

Model-specific part cost (what we can confirm)

The compatible heating element for Kenmore Elite 11087721700 is dryer heating element WP8544771. Your total parts cost increases if you also replace heat-safety components that commonly fail when airflow is restricted.

• Heating element: dryer heating element WP8544771
• Heat safety kit (often replaced with a failed heater): dryer thermal cut-off fuse kit 279973
• High-limit thermostat (sometimes replaced with heat issues): dryer high-limit thermostat WP8557403

Labor and total cost (what varies)

We can’t quote a single “installed price” for 11087721700 because service call fees and hourly rates vary by location and company. Use this as a practical planning range:

• DIY: you typically pay for the element (and any related thermostats/fuses you choose to replace)
• Professional repair: you pay for parts plus a service call and labor time

Repair approach	What you pay for	Cost certainty
DIY replacement	Parts only	High (parts are model-matched)
Professional replacement	Parts + service call + labor	Variable (depends on local rates)

Why it matters

A failed heater on 11087721700 is often linked to overheating from poor venting. If the vent is clogged or crushed, a new element or thermal cut-off can fail again.

Ways to keep the repair cost down

• Clean the lint screen and confirm the vent is clear and not kinked.
• Verify the dryer has proper 240V power (a tripped breaker can cause “runs but no heat”).
• If a thermal cut-off is blown, correct airflow issues before installing new heat parts.
• Follow the disassembly and safety steps in the 11087721700 dryer manual.

Last updated: January 2026

For the Kenmore Elite 11087721700 dryer, the most reliable reset is a power reset: end the cycle, disconnect power for about 1 minute, then restore power and try starting a new cycle. This clears many temporary control glitches without changing any settings permanently.

Reset steps for model 11087721700

• Press Stop/Cancel (or Power) to end the current cycle.
• Unplug the dryer (or switch the breaker off) for 1 minute.
• Restore power.
• Wait 10 seconds.
• Select a cycle and press Start.
• If you see Control Locked, press and hold the Control Lock button for about 3 seconds (button name can vary by console).

For control panel and lock details specific to this dryer, use the 11087721700 dryer manual.

If it still will not run after a reset

A reset will not override a safety shutdown. Check these common causes:

• Door not fully closed or latch not engaging
• House breaker tripped (electric dryers can have lights but still not run or heat)
• Vent restriction causing overheating
• Overheat protection opened (thermal cut-off)
• Failed start switch or loose wiring

If you suspect an overheating event (burning smell, very hot cabinet, repeated shutdowns), inspect the venting first; then consider testing the thermal cut-off components in the dryer thermal cut-off fuse kit 279973.

Quick symptom guide

What happens after reset	Most likely area	Typical next step
Won’t start at all	Door switch/latch, power supply, overheat protection	Confirm door closes, verify breaker, test safety devices
Runs but no heat	Heating circuit, airflow	Check venting, then test heater and thermostats
Stops mid-cycle	Overheating from poor venting	Clean/shorten vent run, clear lint buildup

Why it matters

Resetting can clear a temporary electronic “hang,” but repeated shutdowns usually point to airflow problems or a heat-safety device opening. Fixing the root cause helps prevent long dry times and repeat no-heat or no-start problems.

Last updated: January 2026

On Kenmore Elite dryer model 11087721700, a blown thermal fuse often shows up as a dryer that will not start or runs but will not heat. The sure way to confirm is to unplug the dryer and test the fuse for continuity with a multimeter (see the 11087721700 dryer manual).

Common symptoms to watch for

• Dryer will not start (no motor run)
• Dryer runs but produces no heat
• Cycle stops early or seems to shut down unexpectedly
• Clothes take much longer than normal to dry (often airflow-related)
• Cabinet feels unusually hot during operation

How we confirm a blown thermal fuse

1. Disconnect power (unplug the cord).
2. Access the thermal fuse area (commonly on the blower housing or exhaust duct on many Kenmore 110-style dryers).
3. Pull at least one wire off the fuse terminal.
4. Set your multimeter to continuity or ohms.
5. Touch the probes to the fuse terminals.

What the meter reading means

Meter result	What it indicates	What to do next
Beep or near 0 Ω	Fuse is likely good	Keep troubleshooting the heat or start circuit
OL, infinite, or no beep	Fuse is blown	Replace the fuse and correct the overheating cause

Parts that commonly apply to this repair

For this model, a common replacement option is a kit that includes thermal cut-off components used in the heating safety circuit: dryer thermal cut-off fuse kit 279973. If you are specifically replacing the thermal fuse, match the part by the model-based parts list for 11087721700.

Why it matters

A thermal fuse is a one-time safety device that opens when the dryer overheats. Overheating is most often caused by restricted airflow (lint buildup, crushed vent, blocked outside hood). Fixing airflow helps prevent repeat failures and long dry times.

After you replace the fuse, do these checks

• Clean the lint screen and the lint screen housing
• Inspect and clean the vent duct to the outside
• Use heavy metal venting (not plastic or foil)
• Confirm the outside hood flap opens freely

Last updated: January 2026