CONFIRM THE PART FITS

Home  >  Dryer Drum Support Shaft

Dryer Drum Support Shaft 131777700

★★★★★★★★★★
5
8
4
3
3
3
2
1
1
1
BEST SELLER

Part #131777700

Online price
$56.99
In Stock
For ZIP codes near Edit
60-day return policy

Part Information

This drum support shaft (part number 131777700) is for dryers.

Drum support shaft 131777700 supports the drum at the dryer's back wall while allowing the drum to spin.

Unplug the dryer before installing this part. Wear work gloves to protect your hands.

Reviews

1-8 of 16 reviews
JimD
Patchogue NYReviews 1Votes 0
★★★★★★★★★★
• 1 year ago
JimD• 1 year ago
Just what i needed

Ordered this for my stacked washer and dryer. this part was exactly like the one on my dryer that broke. You need two people to do this job. I removed the top and front and disconnected the belt through the access panel on the rear. took about 2 hours but saved a few hundred dollars having someone do it for us.

Response from Sears PartsDirect:
CS OFFLINE • 1 year ago

We are so thrilled you had a 5-star experience. Thank you for taking the time to leave us a rating. We thank you for choosing Sears Parts Direct for your part needs!

Rotho
Wheatland, WYReviews 1Votes 0
★★★★★★★★★★
• 1 year ago
Rotho• 1 year ago
Very easy installation

Easy to install, hardest part was taking the dryer apart. I did not have instructions so removed a few pieces that were not necessary. But all-in-all the whole process was easy and saved me a lot of money.

Dub T
Cedarville, MIReviews 1Votes 0
★★★★★★★★★★
• 1 year ago
Dub T• 1 year ago
Dryer work again!

Took dryer apart, ordered the obviously broken parts, put back together in short order, and it works fine.

Magnummike
MichiganReviews 1Votes 0
★★★★★★★★★★
• 2 years ago
Magnummike• 2 years ago
Bearing and shaft for Kenmore drier

Easy installation one note I was able to install without accessing rear panel to take belt off of tension pulley. Killed circuit breaker then from front pulled back on pulley arm and removed belt this allowed me to fix without pulling washer/drier out from right corner!

pj19
Green Bay, WIReviews 1Votes 0
★★★★★★★★★★
• 3 years ago
pj19• 3 years ago
old one wore completely through

I wasn't sure what the part was supposed to look like. The one I removed from the dryer was worn and broken into two pieces. I replaced both the dryer shaft and the bearing, and now the dryer runs and is much quieter. I didn't need to removing the top of the dryer to disassemble, but found that I had to remove the top to put the drum back in. I also struggled removing the control panel and reinstalling the belt. There is an access panel on the back which makes the belt install easier.

Linda65
Maryville, TennesseeReviews 1Votes 0
★★★★★★★★★★
• 3 years ago
Linda65• 3 years ago
Not easy to install, but not extremely difficult.

My Kenmore dryer is 15 yrs old. It needed several parts that started with a belt. After getting into it, hubby discovered it needed more than a belt. I ordered the parts, and they arrived quickly. We needed one more part, but I couldn't find it on website. I called customer service, and the very nice young man found the part and shipped it. We are very satisfied with the whole experience. Thank you Sears!

Andrew P.
Reviews 1Votes 0
★★★★★★★★★★
• 4 years ago
Andrew P.• 4 years ago
Second times a charm

Went smoothly running better then it has in years. Definitely need a second person to hold the assembly on the back of the unit while you put the bearing assembly on back of dryer. If you're doing it by yourself a magnet from the back side holds the bearing in place pretty good

Jose97
Reviews 1Votes 0
★★★★★★★★★★
• 4 years ago
Jose97• 4 years ago
good and on timw

i had previous experience, so there was no problem installing it

1-8 of 16 reviews