Kenmore Elite 66517263402 dishwasher Parts

Your dishwasher’s model is printed on the model and serial number label located just inside the door opening on your Kenmore Elite dishwasher. For model 66517263402, open the door and look along the inner tub frame edge for the rating label.

On Kenmore Elite 66517263402 dishwashers, the label is typically visible when the door is open.

• Open the dishwasher door fully.
• Look along the inner tub frame (the rim around the opening).
• Check the left side first, then scan the top edge if needed.
• The label lists Model and Serial.
• Write the model number exactly as shown (all digits).

The model number identifies the exact design family so we can match the correct parts list, diagrams, and repair instructions.

Kenmore dishwashers can look similar across multiple series, but parts like the heating element, water inlet valve, and detergent dispenser can vary by model. Using the exact model number helps prevent ordering the wrong replacement part.

If you are replacing a common item, match by model first, then confirm the part by name and ID. For example, this model uses a dishwasher heating element listed as heater element WPW10082892.

For diagrams and additional identification details, use the owner's manual.

Last updated: February 2026

Yes. We still carry replacement parts for many Kenmore dishwashers, including Kenmore Elite model 66517263402. The key is matching parts by your full model number so you get the correct fit for items like the drain hose, water inlet valve, heater element, or dishrack.

Use the model number 66517263402 to look up the exact part in the diagrams and parts list, then compare the part name and part ID before ordering.

• Confirm the full model number from the rating label (usually on the tub frame near the door).
• Match the symptom to the system (drain, fill, heat, door, racks).
• Use the parts list to cross-check the part name and part ID.
• Replace worn mounting hardware or clamps when you replace hoses.
• Follow the installation and safety steps in the installation guide.

Here are examples of model-matched parts available for this dishwasher:

Kenmore dishwashers are built with serviceable components, so replacing the correct model-specific part is usually faster and more reliable than trying a “close enough” substitute. Using the right part also helps prevent leaks, poor wash performance, and repeat repairs.

Last updated: February 2026

Yes. Your Kenmore Elite dishwasher model 66517263402 uses a filtration system to help keep food soil from recirculating during the wash. For the exact filter style and the correct cleaning steps for your unit, follow the maintenance instructions in the 66517263402 owner's manual.

Kenmore 665-series dishwashers commonly use one of these setups:

• Self-cleaning filter with a grinder: you typically do routine cleaning of the sump area and spray arms, not a removable filter.
• Manual filter system: you remove and rinse the filter screen or filter assembly periodically.
• Hybrid system: a filter plus a chopper or soil separation area.

Use these steps when you are addressing odor, cloudy dishes, or poor cleaning (they apply to most Kenmore Elite dishwashers):

• Turn off power at the breaker before reaching into the sump area.
• Remove the lower rack and inspect the bottom of the tub for debris.
• Check the overfill protection float area for stuck food or labels.
• Rinse any removable screens or filter parts with hot water; use a soft brush if needed.
• Clear spray arm holes if you see mineral buildup or seeds.
• Run a hot cycle after cleaning to flush the wash system.

If cleaning does not restore performance, these parts are commonly related to draining, filling, and heating issues that can mimic a clogged filter:

A clean filtration and wash area helps your 66517263402 maintain water flow through the pump and spray arms, improves drying, and reduces odor caused by trapped food soil.

Last updated: February 2026

Yes, repairing a Kenmore Elite dishwasher like model 66517263402 is usually worth it when the problem is a wear item (hose, valve, dispenser, heater) and the repair cost is reasonable. It is less worthwhile when multiple major components fail at once or the tub is leaking.

Use these checkpoints before you buy parts:

• If the dishwasher is cleaning well after the fix and the racks and tub are in good shape, repair is the better value.
• If you have repeated leaks, heavy rust-through, or multiple failures in a short time, replacement is the better value.
• If the issue is a single, common failure (no fill, no drain, poor drying), repair is typically straightforward.
• If the repair requires major disassembly and you are paying for labor, compare the total cost to the price of a new dishwasher.
• If the problem is tied to installation (drain routing, air gap, leveling), correcting the install often solves it.

These are frequent, fixable problems on dishwashers like the Kenmore 665 series:

Your Use & Care Guide includes a dedicated troubleshooting section plus cleaning and maintenance guidance (including items like drain air gap care). Following those steps first can prevent unnecessary parts replacement and helps you confirm whether you have a true component failure. See the owner's manual.

• Clean the filter area and check for debris around the pump intake before replacing a motor.
• Verify the water supply valve under the sink is fully open and the inlet screen is not clogged.
• Confirm the drain hose has a proper high loop or air gap to prevent backflow.
• If the door drops open or won’t stay up, inspect springs and hinges for wear.

Last updated: February 2026