Owner’s manual
Error Codes
How many cubic feet is a Kenmore model 25520502110 freezer?
Kenmore model 25520502110 is a compact upright freezer; the manual lists this model family at 4.9 cubic feet (shown as 255.20502). For best performance, keep proper airflow clearance and set the temperature control dial to maintain safe frozen-food storage.
Where the capacity is listed
You will find the capacity in the specifications/product record area of the 25520502110 owner's manual. In that section, the manual shows:
- Model 255.20502: 4.9 cu. ft.
- Model 255.20602: 5.8 cu. ft.
- The model and serial number fields for recording your unit information
Quick spec snapshot
| Item | What to expect |
|---|---|
| Capacity for 25520502110 | 4.9 cu. ft. |
| Installation type | Freestanding (not built-in) |
| Recommended clearances | Sides 3/4 in; top 2 in; back 2 in |
Why it matters
Knowing the cubic-foot capacity helps you plan food storage, choose baskets/shelves, and avoid overloading the freezer, which can restrict air circulation and lead to temperature swings.
Helpful setup tips (to match the rated performance)
- Leave the recommended clearance on the sides, top, and back for proper air circulation.
- Place the freezer on a solid, level floor; adjust the front leveling legs as needed.
- Avoid tilting the freezer more than 45 degrees when moving it.
- Use a properly grounded 115V outlet; do not use a 3-prong adapter.
Last updated: January 2026
Is there a reset button on a Kenmore upright freezer?
Kenmore upright freezers like model 25520502110 typically do not have a dedicated “reset” button. The most reliable reset is a power reset: unplug the freezer, wait a few minutes, then plug it back in and set the temperature control again using the dial.
How to reset a Kenmore 25520502110 upright freezer
- Unplug the freezer from the wall outlet.
- Wait 5 minutes (this lets the control and compressor protection reset).
- Plug the freezer back in.
- Turn the temperature control dial to your normal setting.
- Allow cooling time; first-time cool down to the set level commonly takes up to 24 hours.
For model-specific operating details and temperature control guidance, use the 25520502110 owner's manual.
Quick checks if it still will not cool after a reset
- Confirm the outlet has power (try a lamp or phone charger).
- Make sure the freezer is on an exclusive, properly grounded outlet (avoid sharing with another appliance).
- If the freezer was moved or tilted, keep it upright and wait 24 hours before plugging in.
- Verify the temperature control dial is not set to the warmest position.
- Check that the door closes and seals fully; a torn gasket can cause warm air leaks.
If the door is not sealing, replacing the gasket is a common fix; see the midea door gasket 12131000010686.
What “reset” means on this model (and what it does not)
| Reset type | What it does | When to use it |
|---|---|---|
| Power reset (unplug/replug) | Reboots the control and restarts the cooling cycle | After a power outage, odd behavior, no response |
| Temperature dial adjustment | Changes the target coldness level | Freezer too warm or too cold |
| Defrost and restart | Removes heavy frost, restores airflow | Frost buildup, weak cooling, fan noise |
Why it matters
A freezer can stop cooling temporarily due to compressor protection timing, a recent move/tilt, or airflow restrictions from frost. Doing a proper power reset and allowing adequate cool-down time prevents unnecessary parts replacement and helps protect the sealed system.
Last updated: January 2026
What are the most common issues with 25520502110?
The most common issues we see with the Kenmore 25520502110 upright freezer are warm temperatures from airflow or defrost problems, frost buildup from a door seal leak, and control or power-related no-cool symptoms. Use the owner's manual for model-specific operating and care steps.
Most common symptoms and what they usually point to
- Freezer not cold enough: blocked vents, heavy frost on the evaporator, weak evaporator fan, or a control/thermostat issue
- Heavy frost or ice buildup: door not sealing, frequent door openings, humid room air, or a defrost system problem
- Runs constantly or very long cycles: dirty condenser area, warm room location, door leak, or overpacked cabinet restricting airflow
- No power or intermittent operation: loose outlet connection, tripped breaker, or a wiring/control problem
- Door won’t close or cabinet rocks: leveling legs out of adjustment or door alignment issues
Quick checks we recommend first
- Confirm the temperature control is set correctly; if the knob is cracked or slipping, replace the freezer temperature control knob 501118530005.
- Check the door seal all the way around for gaps, tears, or hardened sections; replace the door gasket 12131000010686 if it is not sealing.
- Make sure the freezer is level and stable; adjust the freezer leveling leg 501124540001 if the door swings open or won’t self-close.
- Look for frost on the back interior panel; a solid frost sheet often indicates a defrost airflow issue.
- Avoid overpacking; leave space for air to circulate around shelves and vents.
Common issue-to-fix guide
| What you notice | Most likely cause | What to do next |
|---|---|---|
| Frost around the door | Door not sealing | Inspect/replace gasket; level cabinet |
| Warm temps with lots of frost inside | Airflow restricted or defrost problem | Defrost and check for recurring frost |
| Knob turns but temp doesn’t change | Knob slipping or control issue | Replace knob; then evaluate control |
| Door pops open | Not level, hinge alignment | Level legs; check door alignment |
Why it matters
A small door leak or leveling problem can quickly create frost, reduce airflow, and force the compressor to run longer; that raises energy use and can lead to spoiled food.
Last updated: March 2026
