KitchenAid KSSC42QMS01 built-in refrigerator Parts

KitchenAid “Superba” is a product line name, not a single capacity. For your KitchenAid KSSC42QMS01 built-in side-by-side refrigerator, the exact cubic-foot capacity isn’t identified in the model-specific information we have here, so we can’t confirm a single number for this exact model.

How to confirm the capacity for your exact refrigerator

The most reliable way is to check the model’s rating label and documentation:

• Look for the model/serial label inside the fresh food compartment (often on a side wall).
• Check the specifications section in the KSSC42QMS01 owner’s manual.
• If you have the installation paperwork, compare the model family (42" built-in) to the listed design specs in the KSSC42QMS01 installation guide.

Why “Superba” capacity varies

“Superba” covers multiple KitchenAid refrigerator configurations and sizes, so capacity can differ by:

• Cabinet width (for example, 36", 42", 48" built-in platforms)
• Dispenser vs. non-dispenser door designs
• Interior layout changes across production years
• Freezer/refrigerator compartment proportions

Quick comparison: what you can trust

Source	Best for	Notes
Model/serial label	Exact identification	Confirms the exact model you own (KSSC42QMS01)
Owner’s manual	Model-specific specs	Best place to verify capacity if listed
Retail listings	General guidance	Can be inaccurate if the listing is for a different Superba model

Why it matters

Cubic-foot capacity affects how you plan storage (shelf/bin use), expected ice production needs, and whether a “similar-looking” replacement refrigerator will actually match your household capacity.

Last updated: January 2026

To reset your KitchenAid KSSC42QMS01 side-by-side refrigerator, we recommend doing a power reset: turn the unit OFF, then back ON using the main power switch behind the top grille. This reboots the controls and can clear minor control glitches.

Reset options for KSSC42QMS01

1) Control reset (quick reboot)

Use this when the refrigerator is running but acting “stuck” (odd display behavior, alarms, or cooling logic acting up).

• Press and hold POWER (ON/OFF) on the control panel for about 2 seconds to turn cooling OFF.
• Wait about 10 seconds.
• Press and hold POWER (ON/OFF) again for 2 seconds to turn cooling back ON.
• Allow up to 24 hours for temperatures to stabilize after changes.

2) Full power reset (recommended)

Use this when you want the most complete reset of the refrigerator’s electronics.

• Remove the top grille to access the Power On/Off switch.
• Switch power OFF.
• Wait 2 to 5 minutes.
• Switch power ON.
• Reinstall the top grille.

For the exact grille removal steps and switch location, follow the KSSC42QMS01 use & care manual.

Resetting the water filter indicator (not the same as a full reset)

If you replaced the water filter and only need to clear the filter status:

• Press and hold RESET for 2 seconds to return the display to 99%.

If your filter cap is damaged or missing, use the correct replacement cap for your model, such as the refrigerator water filter cap (black) WP2186494B when applicable.

What to expect after a reset

Reset type	What it affects	What it does not affect
Control reset	Control logic, alarms, cooling cycle restart	Saved temperature set points usually remain
Full power reset	Entire control system power cycle	Does not “factory reset” the refrigerator
Filter reset	Filter status display only	Does not improve water flow by itself

Why it matters

A reset is a safe first step for KSSC42QMS01 when the controls are unresponsive or after a power interruption. It can restore normal operation without replacing parts, and it helps you confirm whether a problem is a control glitch or a true component failure.

Last updated: January 2026

For the KitchenAid KSSC42QMS01 built-in side-by-side refrigerator, the most common issues we see are ice maker or dispenser problems and temperature complaints (warm refrigerator, warm freezer, or temperature swings). Many times the root cause is restricted airflow, a water supply or filter restriction, or a failed cooling component.

Quick checks we recommend first (no parts required)

• Verify the set points are reasonable; factory recommended targets are 0°F freezer and 37°F refrigerator.
• Make sure interior air vents aren’t blocked by food packages.
• Clean the condenser coils behind the top grille; dirty coils can cause long run times and weak cooling.
• If water flow is slow at the dispenser, flush the system and confirm the shutoff valve is fully open.
• If ice tastes off or looks discolored, flush the water system and discard the first batches.

For model-specific control settings, alarms, and troubleshooting steps, use the KSSC42QMS01 use & care manual.

Common symptoms and likely causes

Symptom	Most common causes	What to do next
Ice maker not making ice	Freezer too warm, water supply issue, filter restriction, ice maker fault	Verify temps and water supply; then inspect ice maker operation
Ice dispenser won’t dispense	Ice clumped/jammed, bin not seated, chute door issue	Empty/clean bin; reseat bin; clear chute
Refrigerator warm but freezer OK	Airflow/damper issue, evaporator fan issue, frost buildup	Check vents; listen for fan; check for frost pattern
Noisy operation	Normal sounds, fan noise, airflow restriction	Confirm vents clear; inspect fan area if noise is new or loud

Parts that commonly relate to these problems (for this model)

If troubleshooting points to a failed component, these parts are commonly involved on KSSC42QMS01:

• Refrigerator ice maker WPW10277448 (no ice or inconsistent ice production)
• Refrigerator temperature sensor WP2188820 (temperature swings or inaccurate cooling)
• Refrigerator condenser fan W10181323 (poor cooling, hot cabinet sides, long run times)

Water filter note for KSSC42QMS01

This model uses a base grille water filtration system; the manual references replacement cartridge 4396548 (LC400V). If you’re working on filter-related symptoms, follow the filter steps in the KSSC42QMS01 use & care manual and the KSSC42QMS01 installation guide water system preparation section.

Why it matters

Ice maker and cooling complaints often share the same root causes: restricted airflow, poor heat exchange at the condenser, or restricted water flow. Starting with the basic checks helps protect food temperatures and avoids replacing parts unnecessarily.

Last updated: January 2026