Whirlpool WTW5105HW1 washer Parts

To reset your Whirlpool washer model WTW5105HW1, we recommend doing a simple power reset: turn the washer off, unplug it (or switch the breaker off) for 1 minute, then restore power and start a cycle. This clears many temporary control glitches.

• Press POWER to turn the washer off.
• Unplug the power cord from the outlet (or turn the circuit breaker off).
• Wait 60 seconds.
• Plug the washer back in (or turn the breaker on).
• Lift and close the lid once, then select a cycle and press START/PAUSE.

For additional model-specific operating and care guidance, use the WTW5105HW1 installation & care manual.

A reset will not fix a mechanical failure or a safety interlock problem. Check these common items next:

• Confirm the outlet has power and the cord is firmly seated.
• Make sure the lid is fully closed; a lid lock issue can prevent starting.
• Verify both water faucets are fully open (hot and cold).
• If the tub is full of water, try RINSE & SPIN to drain and spin.
• Look for an error code on the console; it can point to the failed system.

If you suspect the lid is not being detected, the lid lock-sol W11700916 is a common component involved in lid-lock related symptoms.

A proper reset is a fast, no-tools first step that can restore normal operation without replacing parts. If the problem returns quickly, an error code or a failing component (like a lid lock or drain system issue) is more likely than a one-time glitch.

Last updated: January 2026

A Whirlpool washing machine like model WTW5105HW1 typically lasts 14 to 18 years with normal household use and consistent care. Lifespan is most affected by load size habits, detergent use (HE), installation/leveling, and how well you prevent odor and residue buildup.

• Overloading (stresses the drive system, basket, and suspension)
• Using non-HE detergent or too much detergent (causes residue, odors, and extra wear)
• Poor leveling (increases vibration and can shorten component life)
• Hard water and mineral buildup (can affect valves, hoses, and internal surfaces)
• Skipping routine cleaning (can lead to odor, buildup, and performance issues)

For model-specific care steps and cleaning guidance, follow the WTW5105HW1 installation & care instructions manual.

• Run the washer’s Clean Washer cycle regularly (about monthly)
• Leave the lid open between loads so the tub can dry
• Use warm or hot washes sometimes (not only cold) to reduce buildup
• Keep loads balanced to reduce shaking during spin
• Inspect hoses for bulges, cracks, or leaks; replace on schedule

The WTW5105HW1 manual recommends replacing inlet hoses every 5 years to reduce the risk of hose failure. If you need replacements, use a compatible set such as the washer fill hose set 8212545RP.

A washer that is kept clean, level, and not overloaded usually avoids the most common early failures (excess vibration, drainage issues, and fill problems), which is the easiest way to protect long-term reliability.

Last updated: January 2026

On Whirlpool washers like model WTW5105HW1, the most common issue we see is a “won’t start” situation where the control panel lights up but the cycle will not begin. This is often tied to the lid not locking, a control input not registering, or a power/reset condition (not always a failed motor).

• Confirm the washer is plugged into a working, grounded 3-prong outlet (avoid extension cords).
• Make sure the lid is fully closed; press down on the lid at the front edge and try Start again.
• Cancel the cycle and reselect a normal cycle; then press and hold Start/Pause.
• Unplug the washer for 1 minute to reset the control, then try again.
• Verify both water faucets are fully open; some cycles will not start if fill conditions are not met.

If the basic checks above do not help on WTW5105HW1, these are the most common part areas to inspect or test:

• Lid lock system (washer will not run if it cannot confirm the lid is locked)
• Lid strike (the small plastic piece the lock grabs)
• User interface/control inputs (buttons not registering)
• Main control (less common than lid lock issues, but possible)

A washer that powers on but will not start is usually protecting you and the machine. On WTW5105HW1, the lid lock and sensing logic are designed to prevent agitation or spin unless the lid is confirmed closed and locked.

For cycle-start behavior, cleaning routines, and installation checks (power, drain hose setup, leveling), use the WTW5105HW1 installation & care manual.

Related troubleshooting help: Whirlpool belt drive top load washer error codes.

Last updated: January 2026

Yes. Whirlpool model WTW5105HW (the base model family for WTW5105HW1) is discontinued, meaning it is no longer being manufactured as a current model; however, we can still help you keep your WTW5105HW1 running with compatible replacement parts and care steps from the WTW5105HW1 installation & care manual.

Discontinued does not mean your washer is unsupported. It typically means:

• New units may be harder to find through retailers
• Service and maintenance still follow the same Whirlpool procedures
• Replacement parts may remain available for years
• You should match parts by model number WTW5105HW1, not just “WTW5105HW”

We recommend focusing on the wear items and the most common failure points:

• Replace fill hoses every 5 years to reduce leak risk
• Keep the lid open between loads to help prevent odor
• Run the Clean Washer cycle monthly (or every 30 loads)
• Check for slow fill or no fill symptoms early (often water supply or valve related)
• Address draining issues quickly to avoid strain on the pump

When a washer is discontinued, the best way to avoid downtime is to use the exact model number (WTW5105HW1) when selecting parts and to follow the maintenance schedule. That prevents ordering the wrong component and reduces repeat failures.

Last updated: January 2026