Kenmore 11023102310 washer Parts

Your Kenmore washer model number is printed on the appliance ID label; on Kenmore model 11023102310, you will typically find it under the lid (top-load design) or on a label on the back of the cabinet. Once you have the full model number, we can match the correct parts and installation specs in the 11023102310 owner's manual.

• Lift the lid and check the underside of the lid or the rim around the tub opening
• Check the rear panel of the washer cabinet near the power cord
• Look along the side edges of the cabinet near the control console
• Write down both the model number and serial number from the same label
• Take a clear photo of the label before ordering parts

Many Kenmore washers use a model format that starts with 110 followed by additional digits (as in 11023102310). The full model number is what we use to confirm fit for parts like a lid lock, actuator, drive belt, or gear case.

Kenmore model families can look similar, but small model-number differences can change the correct lid lock assembly, water inlet valve, or drive system parts. Using the exact model number prevents wrong-part returns and repeat repairs.

• Check any purchase paperwork or installation notes you saved
• Look for a duplicate label on the back of the cabinet
• If you are replacing a common wear item, match by model first, then confirm by part ID (for example, the washer lid lock assembly W10404050 is model-specific)

Last updated: February 2026

To reset a Kenmore top-load washer model 11023102310, we recommend doing a simple power reset: turn the washer off, unplug it for 1 minute, then plug it back in and press START/PAUSE/Unlock Lid to restart the cycle. Use the 11023102310 owner's manual for the exact control-panel behavior on your washer.

• Power reset: Unplug for 60 seconds, plug back in.
• Cycle restart: Close the lid, then press START/PAUSE/Unlock Lid.
• Clear a paused state: If Lid Locked is blinking, press START/PAUSE/Unlock Lid and wait for movement to stop before opening.
• After opening the lid: Close the lid and press START/PAUSE/Unlock Lid to resume.
• If it filled but never started: Close the lid and press START/PAUSE/Unlock Lid; the washer will not begin with the lid open.

These checks solve the most common “no start” complaints on this style of Kenmore washer:

• Confirm the washer is plugged into a grounded 3-prong outlet (no extension cord).
• Reset a tripped circuit breaker or replace a blown fuse.
• Make sure the lid is fully closed; the washer will not start or fill with the lid open.
• Avoid opening the lid during the sensing phase; it can force sensing to start over.
• If the lid does not lock or unlock correctly, inspect the washer lid lock assembly W10404050.

A “reset” on model 11023102310 mainly clears a paused control state and ensures the lid-lock and sensing steps can complete. If the lid-lock system cannot confirm the lid status, the washer can stop to prevent spinning with an open lid.

Last updated: February 2026

For Kenmore washer model 11023102310, we unclog the drain hose by safely disconnecting it, clearing the blockage, then reinstalling it correctly so the washer can pump out water within the normal drain time. Use the placement rules in the 11023102310 installation guide to prevent repeat clogs.

• Unplug the washer.
• Turn off both water faucets.
• Keep a shallow pan and towels ready for water in the hose.
• If the tub is full, bail out water first to reduce spills.

1. Pull the washer forward and locate the drain hose at the back.
2. Disconnect the hose from the household drain (standpipe or laundry tub) and drain any water into a bucket.
3. Check the hose end for lint, coins, socks, or sludge; remove debris by hand.
4. Flush the hose with hot water; for buildup, soak the clogged end in hot water mixed with vinegar for 20 to 30 minutes, then flush again.
5. If the hose is clear but draining is still slow, check the pump for small items; a restricted pump often acts like a clogged hose. Replacing the washer drain pump assembly WPW10276397 restores normal flow when the pump is jammed or worn.

Follow these installation rules from the model’s setup instructions:

• Keep about 4.5 in. (113 mm) of drain hose inside the standpipe.
• Do not force extra hose down into the standpipe.
• Do not lay the hose on the bottom of a laundry tub.
• Use the drain hose form and secure the hose to the drain.

A partially clogged drain hose can leave loads wet, trigger long-drain symptoms, and strain the drain pump. Correct standpipe depth and hose routing are the fastest way to stop repeat clogs.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11023102310, routine care (proper loading, leveling, and periodic cleaning) helps you reach the high end of that range; neglected maintenance and chronic out-of-balance loads shorten it.

Most washers fail early from wear items and repeated stress, not from one-time events.

• Load size: overloading strains the drive system and suspension
• Out-of-balance spinning: accelerates wear on the tub support and dampers
• Water quality: sediment can reduce fill performance over time
• Drain habits: coins, lint, and small items can damage the pump
• Maintenance: cleaning and inspection prevents small issues from becoming major repairs

These are frequent wear points on top-load designs like the 11023102310.

We recommend following the care steps in the 11023102310 owner's manual and adding these habits:

• Keep loads evenly distributed; mix large and small items
• Use the right detergent amount to reduce residue buildup
• Check pockets to keep coins and screws out of the drain path
• Inspect fill hoses periodically; replace if bulging or cracking
• Level the washer so it does not “walk” during spin

A washer that stays balanced and drains and fills correctly puts less stress on the gear case, actuator, belt, and tub components. That directly improves reliability and helps you avoid repeat breakdowns.

Last updated: February 2026

The exact wash capacity (in cubic feet) for Kenmore model 11023102310 is listed in the product specifications section of the 11023102310 owner's manual. For most Kenmore top-load washers in this style, capacity commonly falls in the 3.0 to 4.5 cu. ft. range.

In the 11023102310 owner's manual, look for sections labeled “Specifications,” “Features,” or “Model information.” Capacity is typically shown as cu. ft. (cubic feet).

What to check in the specs area:

• Capacity in cu. ft.
• Basket size or “tub volume” wording
• Cycle/load guidance (bulky, bedding, deep water wash)
• Electrical requirements (helps confirm you are reading the correct document)

Capacity matters most when you are deciding how much to load and how well the washer can balance during spin.

Using the right capacity helps prevent out-of-balance spinning, reduces wear on the drive belt and suspension, and improves cleaning by leaving enough room for clothes to move through water and detergent.

Last updated: February 2026