Kenmore Elite 11046742702 washer Parts

Yes. Your Kenmore Elite washer model 11046742702 uses a drain pump clean-out (often called a pump filter or coin trap) that catches lint and small items before they reach the drain pump. Cleaning it helps prevent slow draining and drain errors.

On most Kenmore Elite front-load designs like 11046742702, the clean-out is part of the drain system at the bottom front of the washer, behind a small access panel (or lower toe panel). The exact access method and steps are shown in the 11046742702 owner's manual.

• Unplug the washer (or switch off the breaker).
• Place towels and a shallow pan under the lower front access area.
• Open the lower access panel.
• Drain any water slowly (some models use a small drain hose; others drain when you loosen the cap).
• Unscrew the clean-out cap, remove debris (coins, buttons, lint), and rinse the cap.
• Reinstall the cap snugly, close the panel, then run a quick rinse and drain to confirm no leaks.

If the clean-out is clear but the washer still drains slowly, hums, or leaves water in the tub, the drain pump or drain path is usually the next place we check.

A clogged pump clean-out can trigger drain problems, cause longer cycle times, and leave odors from standing water. Keeping the drain path clear protects the pump and helps your Kenmore washer run quieter and more reliably.

Last updated: February 2026

To force your Kenmore Elite washer model 11046742702 to drain, cancel the cycle and run Drain & Spin: press STOP twice, press POWER, select DRAIN & SPIN, then press and hold START for about 1 second. Steps match the 11046742702 owner's manual.

• Press STOP twice to cancel the current cycle
• Press POWER
• Select DRAIN & SPIN
• Press and hold START (about 1 second)
• Wait for the cycle to finish; the door unlocks after the spin completes

A no-drain problem is usually a restriction in the drain path or a failed drain component.

• Check the drain hose for kinks, crushing, or a clogged standpipe
• Make sure the drain hose is not shoved too far down the standpipe (it can cause siphoning or poor draining)
• If you hear the pump running but water barely moves, check for a blockage between the tub and pump
• If you do not hear the pump at all during Drain & Spin, the pump or control may be at fault
• Inspect for leaks around the pump area and hoses

• Unplug the washer before checking hoses or wiring
• If the water level or temperature is high, the washer drains automatically before the door unlocks

Forcing a proper drain protects the motor control, prevents standing water odors, and helps avoid door-lock issues that can happen when the washer cannot complete the drain portion of the cycle.

Last updated: February 2026

For the Kenmore Elite 11046742702 washer, the closest thing to a “hard reset” is canceling the cycle and power-cycling the washer; this clears the current cycle and often restores normal control operation. Use the control-panel cancel steps first, then unplug for a few minutes if the washer is still acting up.

• Press STOP twice to cancel the cycle.
• Press POWER to turn the washer off.
• Unplug the washer (or switch the breaker off) for 1 to 5 minutes.
• Restore power.
• Select a cycle, then press and hold START for about 1 second to begin.

For the exact button names and cycle behavior on this model, follow the steps in the 11046742702 owner's manual.

If the door stays locked, the washer may need to drain first. We use this manual drain sequence:

• Press STOP twice.
• Press POWER.
• Select DRAIN & SPIN.
• Press and hold START for about 1 second.

A reset helps with control glitches, but it will not correct a drain or door-latch failure. If symptoms match these, we focus on the likely parts:

• Won’t drain, humming, or stops mid-cycle: check the pump 280187 and the tub-to-pump hose for clogs.
• Door won’t lock or unlock: inspect the washer door lock WP8183270.
• Won’t fill or fills slowly: check inlet screens and consider the water inlet valve.

Canceling correctly prevents repeated error conditions, protects the door lock mechanism, and helps the control board restart a cycle cleanly (especially after a power interruption or an interrupted wash).

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end lineup, and the Kenmore Elite washer model 11046742702 is built with premium features and durability upgrades compared to basic Kenmore washers, including a stainless steel wash drum and advanced cycle options described in the 11046742702 owner's manual.

On washers like model 11046742702, “high end” typically shows up as better materials, more specialized cycles, and stronger performance features.

• Stainless steel wash drum construction (premium durability)
• Sanitizing temperature option (NSF-certified sanitizing performance is described in the manual)
• More cycle and option control (soil level, wash temp, spin speed selections)
• Designed for reduced vibration and better overall performance when properly installed
• Support for pedestal and stacking configurations (with the correct kit)

If you are comparing washer tiers, “Elite” usually means you are paying for stronger components and more capability. For example, the manual for this model calls out a limited lifetime warranty on the stainless steel drum and a 10-year limited warranty on the plastic tub, which are the kinds of durability signals commonly associated with higher-end lines.

If performance drops (slow drain, leaks, door issues), these are common repair areas on front-load washers:

• Pump 280187 (drain performance)
• Washer door boot WP8182119 (door seal leaks, odors)
• Washer door lock WP8183270 (won’t lock, won’t start)

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For the Kenmore Elite 11046742702, lifespan depends most on load size, detergent use, and routine care; consistent cleaning and leak prevention help you reach the upper end of that range.

Most washers fail from wear in a few common systems: draining, water fill, and door sealing.

• Usage volume: multiple loads per day shortens life faster than light weekly use
• Overloading: strains the drive system and suspension
• Water quality: hard water increases scale and residue buildup
• Ventilation: leaving the door closed traps moisture and promotes odor and corrosion
• Preventive care: cleaning and hose checks reduce leaks and pump clogs

We recommend following the care steps in the 11046742702 owner's manual. Key habits:

• Clean the washer regularly (tub, door glass, and gasket folds)
• Check and replace water inlet hoses if they show bulging, cracking, or seepage
• Use HE detergent and measure carefully to prevent oversudsing and residue
• Keep the door slightly open between loads to dry the boot area
• Address small leaks immediately before they reach the motor control area

If you are seeing leaks, draining issues, or door problems, these parts are frequent culprits on front-load designs:

Knowing the 10 to 15 year lifespan helps you decide when maintenance and a targeted repair (like a pump or door boot) makes sense versus planning for replacement, especially if multiple major systems start failing close together.

Last updated: February 2026

Your Kenmore Elite washer’s model number is printed on a rating label on the cabinet. On Kenmore Elite front-load washers like model 11046742702, the label is most often in the door opening (door jamb) or just behind the door; some versions also place it on the back or top edge of the control panel.

• Open the washer door and check the door jamb (the frame area the door closes against)
• Look just behind the door on the front cabinet lip
• Check the back of the control panel
• Check the top edge of the control panel (you may need a flashlight)
• Look on the side of the main cabinet near the bottom

For this Kenmore Elite series, the model format commonly starts with 110. and then continues with more digits. Your full model number will match the label exactly (for example, 11046742702).

We use the exact model number to match the correct parts list, wiring, and troubleshooting steps. Even small differences in the last digits can change items like the door lock, drain pump, or door boot.

• Copy the model number character-for-character from the label
• Take a clear photo of the label before ordering parts
• Use the model number when referencing the 11046742702 owner’s manual

Last updated: February 2026

Kenmore Elite is a premium Kenmore product line that has been produced across multiple years and generations, not a single one-time model release. For your Kenmore Elite washer model 11046742702, the exact manufacture date is typically tied to the unit’s serial number and date-of-purchase records; we use the 11046742702 owner's manual to confirm model identification and features.

Use these quick checks to narrow it down accurately:

• Look for the serial number label (commonly on the door opening, behind the door, or on the cabinet frame)
• Record the model number 11046742702 and the full serial number exactly as shown
• Check your purchase receipt or delivery paperwork for the purchase date
• Compare the washer’s features (for example, NSF-certified sanitize cycle) to the feature list in the manual
• If you are stacking units, confirm whether your setup matches the stack kit guidance in the manual (stack kit 8541503 is referenced)

Kenmore Elite is a tier/series name, so it spans many washer designs (front-load and top-load), control styles, and feature sets. That is why the best way to date a specific unit is by serial number rather than the Elite name alone.

Knowing the approximate build timeframe helps us match the right replacement parts (like a door boot, drain pump, or motor control board) and avoid ordering a look-alike part that does not fit your exact production run.

Last updated: February 2026