Kenmore Elite 66513962K013 undercounter dishwasher Parts

To reset the control on your Kenmore Elite dishwasher model 66513962K013, we recommend using the built-in reset sequence: press CANCEL/DRAIN twice, then choose a new cycle and press START/RESUME. This clears the current cycle and restarts the control logic. See the 66513962K013 owner's manual for the exact button sequence.

Quick reset steps (control reset)

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Open the door fully.
• Press CANCEL/DRAIN two times to reset the control.
• Select your new cycle and any options.
• Press START/RESUME.

If you need to stop and drain first

If there is water sitting in the bottom, use the cancel and drain procedure:

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Press CANCEL/DRAIN once.
• Close the door within 3 seconds so the drain cycle can run.
• Let it drain completely (the cancel/drain indicator typically turns off after about 2 minutes).

What “reset” does (and does not) do

Action	What it does	What it does not do
CANCEL/DRAIN twice	Resets the control and lets you restart a cycle	Fix a drain blockage or water supply problem
CANCEL/DRAIN once + close door	Runs a drain cycle if water remains	Clean the filter or clear the hose

Why it matters

Resetting the control is the fastest way to recover from a stuck cycle, flashing option lights, or a cycle you want to restart. If the dishwasher still will not drain or refill after a reset, the issue is usually mechanical (filter restriction, drain hose routing, or a failing pump/valve).

Parts that commonly relate to “won’t drain” after a reset

• Dishwasher drain pump WPW10348269 (moves water out of the tub)
• Dishwasher drain hose 8269144A (carries drain water to the sink drain or disposer)
• Dishwasher filter W10872845 (helps prevent debris from reaching the pump)

Last updated: January 2026

On the Kenmore Elite dishwasher model 66513962K013, the AE code (often paired with E1) points to a water-level problem: the circulation pump can run abnormally fast when the tub water level is too low, or water in the base can trip the flood switch. Follow the reset and leak checks in the 66513962K013 owner’s manual.

What to do right away

• Press Cancel/Drain (if the controls respond) to stop the cycle.
• Unplug the dishwasher or switch OFF the breaker.
• Shut off the water supply valve under the sink.
• If you see water on the floor, dry it up to prevent slipping.
• Wait 5 minutes, then restore power and try a quick cycle to see if the code returns.

Common causes (and what to check)

AE is usually triggered by one of these conditions:

• Low water level in the tub (fill problem)
• Water in the base pan (leak or overflow tripping the float or flood switch)
• Drain issue that leaves the unit partially empty during wash
• Suds/over-foaming from the wrong detergent (hand soap or too much detergent)

Quick checks you can do

What you notice	Most likely cause	What to check next
AE shows early in the cycle	Not filling correctly	Water supply valve open; inlet screen; consider dishwasher water inlet valve W11175771
AE after a leak or puddle	Water in base tripped safety	Look for drips at door, hose, pump area; dry base and re-test
Standing water or slow drain	Drain restriction	High loop/air gap, disposer knockout, hose kinks; consider dishwasher drain hose 8269144A
Dishes gritty, poor wash	Filtration restriction affecting flow	Clean the filter system; consider dishwasher filter W10872845

Why it matters

AE is a protection signal. Running with low water level can reduce cleaning performance and strain the wash system; water in the base indicates a leak condition that can keep the dishwasher from operating normally.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66513962K013, the F4E1 service code points to a wash motor or wash pump problem (the dishwasher is not circulating water correctly). In most cases, the fix is to diagnose the wash motor circuit and replace the failed motor/pump component, then clear the code using the reset steps in the 66513962K013 user manual.

What you will usually notice with F4E1

• Dishes come out dirty because spray pressure is weak or missing
• You hear a drain pump running, but little or no “wash” sound during the cycle
• The unit may fill and then stop washing, or end early with a service message
• Water may be present in the tub but not moving through the spray arms

Quick checks before replacing parts

Turn off power at the breaker before any inspection.

• Confirm the dishwasher is getting water (listen for fill at the start)
• Check for a clogged filter and clean it if needed (a restricted filter can reduce circulation)
• Make sure spray arms can spin freely and are not blocked by tall items
• Run a Cancel/Drain and restart a cycle to see if the code returns immediately

Parts that commonly relate to “no wash” symptoms

If the dishwasher fills but does not circulate, these are common suspects:

Symptom	Most likely area	Example part for this model
Fills but no spraying sound	Wash motor/pump not running	Dishwasher pump and motor assembly WPW10328226
Drains fine but won’t wash	Control not powering motor or motor failed	Dishwasher electronic control board WPW10195344
Poor cleaning, debris in tub	Filtration restriction	Dishwasher filter W10872845

Clearing the code after a repair

Many Kenmore Elite dishwashers require a keypad sequence to exit a service state after the underlying problem is corrected. Use the exact reset procedure and button sequence shown in the 66513962K013 user manual.

Why it matters

When the wash motor is not circulating water, detergent cannot dissolve and spray arms cannot clean properly. Continuing to run cycles with an F4E1 condition typically leads to repeated service codes and consistently poor cleaning.

Last updated: January 2026

Common problems on the Kenmore Elite 66513962K013 dishwasher include not starting or stopping mid-cycle (door not fully latched or Start/Resume blinking), not draining (kinked hose or disposer knockout plug still in place), poor cleaning from hard water buildup, and detergent not dispensing when items block the wash system. See the 66513962K013 owner's manual for model-specific troubleshooting steps.

Most common symptoms and what usually causes them

• Dishwasher does not run: door not closed and latched, Start/Resume light blinking, cycle not selected, or a tripped breaker/fuse.
• Detergent remains in the dispenser: loading blocks the wash system or dispenser area; cycle pauses are normal.
• Not draining: kinked drain hose, food obstruction in drain/disposer, or disposer knockout plug not removed.
• Hard water residue or cloudy glassware: mineral deposits; rinse aid missing; filters need cleaning.
• Odors or noisy operation: food debris in filtration area or drain path; occasional noise from normal water movement.

Quick checks we recommend before replacing parts

1. Confirm the door closes fully and latches; if Start/Resume is blinking, close the door and press START/RESUME.
2. Verify power: check the house breaker or fuse.
3. If connected to a food waste disposer, confirm the disposer inlet knockout plug was removed.
4. Inspect the drain hose for kinks and check for food obstructions.
5. Address hard water: incoming water should be at least 120°F (49°C); use rinse aid and clean the filtration system regularly.

Parts that commonly solve these issues (when symptoms match)

Symptom	Common part involved	Example part for this model
Won’t drain or leaves water	Drain pump or drain hose restriction	Dishwasher drain pump WPW10348269 or dishwasher drain hose 8269144A
Poor cleaning, debris left behind	Filter or spray system blockage	Dishwasher filter W10872845 or dishwasher spray arm WPW10195601
Leaks at the door area	Door seal	Seal WPW10497235

Why it matters

Most “dishwasher problems” on the 66513962K013 trace back to airflow and waterflow basics: a fully latched door, correct fill temperature, clear drain path, and a clean filtration system. Fixing those first prevents repeat clogs, poor wash results, and unnecessary part replacement.

Last updated: January 2026