Kenmore 25360083412 refrigerator Parts

The Kenmore refrigerator model 25360083412 is typically about 32 inches wide, 65-3/4 inches tall, and 26-5/8 inches deep. For the exact cabinet and clearance requirements for your installation, we recommend confirming measurements in the 25360083412 installation guide.

What to measure (so it fits the space)

Measure your opening in three places (top, middle, bottom) and use the smallest number.

• Width: cabinet opening side-to-side
• Height: floor to the lowest overhead cabinet or trim
• Depth: from the back wall to the front edge of counters (and allow for door swing)
• Pathway: doorways, hallways, and turns on the way to the kitchen
• Level floor: a level cabinet helps doors close and seal correctly

Clearance guidelines to plan for

The installation instructions call out these minimum clearances for airflow and hookups:

Location	Minimum clearance
Sides and top	3/8 inch
Rear	1 inch

Why the “size” can feel different in real life

Even when the cabinet dimensions match, the refrigerator can need more room because of handles, door swing, and the space required behind the unit for electrical and water connections.

Helpful install notes for this model

From the installation guidance for model 25360083412:

• Use a grounded outlet; do not use an extension cord or adapter plug
• Keep the refrigerator away from direct sunlight and nearby heat sources
• Plan for a cold water line (30 to 100 psi) if your unit has an ice maker
• Use 1/4-inch OD copper tubing for the water supply line
• Level the cabinet so it tilts about 1/4 inch to 1/2 inch front-to-back to help doors close

Last updated: January 2026

For Kenmore refrigerator model 25360083412, the most reliable way to get cubic feet is to look up the capacity in the model’s specifications section of the 25360083412 owner's manual. If you need a quick estimate, we calculate interior volume from measurements (length x width x height in inches, divided by 1,728).

Best ways to find cubic feet (in order)

• Check the specifications/capacity listing in the 25360083412 owner's manual.
• Look for a rating label inside the fresh food section (often on a side wall or near crisper drawers); it sometimes lists capacity.
• Search by the full model number 25360083412 and compare results to the manual specs.
• Estimate capacity by measuring the usable interior space (see steps below).

How to estimate cubic feet by measuring

1. Empty the compartment you are measuring (fresh food and freezer can be estimated separately).
2. Measure the usable interior:
   • Width: wall to wall (ignore door bins)
   • Depth: back wall to the front edge of shelves/drawers
   • Height: floor to ceiling of the compartment
3. Multiply: width x depth x height (in inches).
4. Divide by 1,728 to convert cubic inches to cubic feet.

Quick conversion table

What you have	What to do	Result
Inches (W x D x H)	Multiply, then divide by 1,728	Cubic feet (approx.)
Separate compartments	Calculate each, then add	Total cubic feet (approx.)

Why the model number usually is not enough

Kenmore model numbers (including the 253 prefix) identify the product line and configuration, but they do not consistently encode the exact interior capacity. Capacity can also vary with shelf design, ice maker setup, and liner changes.

Related help for Kenmore refrigerators

If you are troubleshooting display codes while checking specs, use Kenmore 253 series french door refrigerator error codes to match the code to the likely system (cooling, fan, sensor, defrost).

Last updated: January 2026

To reset your Kenmore refrigerator model 25360083412, we recommend a simple power reset: unplug the refrigerator (or switch the breaker off) for about 5 minutes, then restore power. This clears many control glitches and can help the refrigerator restart normal cooling.

Reset steps (power cycle)

• Unplug the refrigerator from the wall outlet, or turn the circuit breaker OFF.
• Wait 5 minutes (this lets the control board fully power down).
• Restore power.
• Give the refrigerator 24 hours to stabilize temperatures after a reset.
• If you have an ice maker and you are not using a water supply, keep the ice maker OFF (the installation instructions note this). See the 25360083412 installation guide.

If the reset did not fix the problem

A reset helps with temporary electronic issues; it will not correct airflow, defrost, or sealed-system failures. Check these common causes next:

• Condenser coils: dirty coils can cause warm temps and long run times.
• Door seal: gaps or a torn gasket can cause frost and temperature swings.
• Evaporator fan: if the freezer is cold but the fresh-food section is warm, airflow is often the issue.
• Temperature sensor: a bad sensor can cause incorrect cooling decisions.
• Control board: if the display or cooling logic is erratic, the board can be involved.

Parts that commonly relate to “won’t cool” symptoms

Symptom you notice	Common area to check	Example part for this model
Fresh food warm, freezer cold	Evaporator airflow	Refrigerator evaporator motor 242077705
Temps fluctuate or seem inaccurate	Temperature sensing	Refrigerator temperature sensor 240597220
Lights out (not a reset issue)	Interior lighting	Refrigerator light bulb 316538904

Why it matters

Resetting clears minor control-board lockups and can restore normal operation quickly. If symptoms return right away, focusing on airflow (fans, vents), sealing (gaskets), and temperature feedback (sensors) prevents food spoilage and reduces compressor strain.

For display or diagnostic issues, use Kenmore 253 series french door refrigerator error codes to match any code to the most likely failure.

Last updated: January 2026

Kenmore is a brand name, and model 25360083412 is part of Kenmore’s 253-prefix refrigerator family that is widely associated with Frigidaire/Electrolux-built units. For confirmation details tied to your exact unit, check the identification label and the documentation in the 25360083412 owner's manual.

How to confirm the actual manufacturer on your refrigerator

We recommend verifying using the model and serial tag on the cabinet because Kenmore appliances are produced by different manufacturers depending on the model series.

• Look for the model/serial label inside the fresh food compartment (often on a side wall) or near the crisper area.
• Confirm the full model number matches 25360083412 exactly.
• Note the serial number and any manufacturing code on the tag.
• Compare the tag information to the documentation in the 25360083412 owner's manual.
• If you are ordering parts, match by model number first, then confirm the part fits by description.

What the “253” prefix typically indicates

Many Kenmore refrigerators that start with 253 are commonly tied to the Frigidaire/Electrolux manufacturing family. This matters most for parts compatibility and service procedures.

What you see	What it usually means	Why you care
Model starts with 253	Often Frigidaire/Electrolux-built Kenmore	Parts diagrams and components tend to align with that platform
Kenmore branding on door	Retail brand, not the factory	Manufacturer can vary by model series
Model/serial tag inside cabinet	Best source for exact identification	Helps ensure correct parts and service info

Why it matters (parts and troubleshooting)

Knowing who built the platform behind your Kenmore 25360083412 helps you choose the right repair approach and compatible components (like door gaskets, fan motors, and control boards). It also helps when you are diagnosing issues such as cooling problems or error codes.

If you are troubleshooting display or cooling faults, we use the Kenmore 253 series french door refrigerator error codes guide as a fast starting point for common code meanings and next checks.

Last updated: January 2026