Kenmore Elite 25344503601 refrigerator Parts

Kenmore Elite refrigerator dimensions vary by model and style; for the Kenmore Elite 25344503601 side-by-side, the exact height, width, and depth are listed in the installation guide for your unit. Most side-by-side refrigerators are roughly 32 to 36 inches wide, 65 to 71 inches tall, and 30 to 35 inches deep (not counting handles).

How to get the exact dimensions for model 25344503601

Use the measurements in the installation guide because it includes the clearances needed for doors to swing and for airflow.

• Measure width at the cabinet (exclude handles unless the guide says otherwise)
• Measure height from floor to top hinge cover area
• Measure depth in two ways: cabinet-only and with handles
• Confirm door swing clearance for the freezer and fresh food doors
• Allow space behind the unit for the water line and power cord

Typical sizing and clearance checklist (side-by-side)

These are common planning numbers we use when the guide is not in hand yet.

What you are planning for	Typical range	What to verify in the guide
Cabinet width	32 to 36 in.	Exact width and whether trim affects fit
Overall height	65 to 71 in.	Hinge cover height and leveling leg range
Depth	30 to 35 in.	Depth with handles and door-open clearance
Airflow clearance	1 to 2 in.	Minimum rear and top clearance

Why it matters

Correct dimensions prevent installation problems like doors hitting walls, poor ventilation that hurts cooling performance, and kinks in the water supply line for the ice maker and dispenser.

Parts that can affect “depth” and fit

If you are planning around protrusions, these parts can change how the front of the refrigerator sits in the opening:

• Door hardware and handles (example: refrigerator door handle 241531403)
• Dispenser components on the freezer door
• Door alignment and closing hardware

If you also need replacement parts or accessories for this model, you can order from the parts list for Kenmore Elite 25344503601 or search by model on Sears PartsDirect.

Last updated: February 2026

On Kenmore Elite refrigerator model 25344503601, the ER IF code points to an ice fan (ice room fan) airflow problem. That fan pushes cold air through the freezer door ducting to keep the ice maker area cold; when airflow drops, the control reports ER IF.

What to check first (fast, no parts)

• Power reset: unplug the refrigerator for 5 minutes, then restore power.
• Make sure the freezer door closes fully and is not held open by bins.
• Clear ice buildup around the ice chute and dispenser area; never chip ice with sharp tools.
• Confirm freezer temperature is set correctly (most side-by-sides run best near 0°F in the freezer).
• Listen for the fan: a failed ice fan often gets noisy, intermittently runs, or is silent.

Common causes and what they mean

What you notice	Most likely cause	What to do next
Ice maker area is warm, ice clumps	Ice fan not moving air	Inspect for ice blockage; if fan will not run, plan a fan repair
Fan runs but airflow is weak	Frost or ice restricting ducting	Defrost/clear blockage; check for recurring frost issues
Code returns after reset	Control not seeing expected fan feedback	Check wiring connections; consider control diagnosis
Frost patterns, warming, then refreezing	Defrost system issue affecting airflow	Check defrost components and airflow paths

Parts that are often involved

If you confirm a fan or defrost-related airflow issue, these model-matched parts are commonly used in repairs:

• Refrigerator evaporator fan blade 5308000010 (damaged blade can reduce airflow and cause noise)
• Refrigerator defrost bi-metal thermostat 5303918214 (defrost problems can lead to ice buildup that blocks airflow)

Why it matters

The ice fan is what keeps the ice maker compartment cold. When airflow is restricted, you can get soft ice, clumping, slow ice production, and temperature swings that stress the cooling system.

Where to find model-specific guidance

For control locations, access steps, and safety notes for your exact unit, use the owner's manual and the installation guide. If you need to order parts for model 25344503601, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

For Kenmore Elite refrigerator model 25344503601, the warranty is 1 year for defects in materials or workmanship, plus a full 5-year limited warranty on the sealed refrigeration system (refrigerant, connecting tubing, and compressor) when installed, operated, and maintained as instructed in the owner's manual.

What’s covered and for how long

• 1 year from purchase date: defects in material or workmanship (general appliance coverage).
• 5 years from purchase date: sealed refrigeration system only (refrigerant, connecting tubing, compressor).
• 90 days: if the refrigerator is used for other than private family purposes (non-residential use).

What the sealed system warranty means

The sealed system is the closed-loop cooling hardware that makes the refrigerator cold. It typically includes:

• Compressor
• Refrigerant
• Sealed connecting tubing

If you are troubleshooting a cooling failure, sealed-system coverage matters because sealed-system repairs are usually the most labor-intensive and expensive.

Common items not covered (typical exclusions)

Even during the warranty period, the warranty language for this model calls out “expendable” items that wear out in normal use. Examples include:

• Water filters
• Light bulbs
• Other routine wear items

If you need a replacement water filter for this model, we list the compatible genuine Kenmore refrigerator water filter WFCB on this page.

Quick reference table

Coverage area	Typical examples	Coverage length
General refrigerator	Controls, wiring, non-sealed components	1 year
Sealed refrigeration system	Refrigerant, tubing, compressor	5 years
Wear items	Filters, light bulbs	Not covered as defects

Why it matters

Knowing whether you are inside the 1-year general coverage or the 5-year sealed-system coverage helps you decide whether to focus first on common service parts (like a thermostat or sensor) versus sealed-system diagnosis.

If you are shopping for maintenance parts or replacements, you can order parts for Kenmore Elite 25344503601 from the parts list on this page, or search by model number on Sears PartsDirect.

Last updated: February 2026

Common problems on the Kenmore Elite 25344503601 side-by-side refrigerator include no cooling or warm temperatures (often tied to compressor start issues or airflow problems), ice maker or dispenser troubles, and control-related failures. We use the symptoms and a few quick checks to narrow down the most likely part.

Most common symptoms and what they usually point to

• Not cooling or weak cooling: dirty condenser coils, evaporator fan issue, start relay problem, or sealed system/compressor trouble
• Ice maker not making ice: water supply issue, frozen fill path, dispenser/ice mechanism problem
• Ice dispenser not dispensing: jammed ice, chute door not sealing, auger motor issue
• Water tastes/flows poorly: clogged water filter
• Frost buildup or temperature swings: defrost system problem (thermostat, heater circuit, airflow)

Quick checks we recommend first (safe, fast)

1. Confirm the refrigerator is on a dedicated 115V outlet and avoid extension cords (power issues can mimic failures). See the installation guide.
2. Set temps to typical targets and give the unit 24 hours to stabilize.
3. Listen for the evaporator fan in the freezer; no fan noise often means poor airflow.
4. If the dispenser is jammed, never use sharp tools to break ice in the bin (it can damage the mechanism). See the owner's manual.
5. If water flow is slow or tastes off, replace the filter and flush the system.

Parts that commonly fix these problems on this model

Problem area	Common fix	Example part on this page
Water quality/flow	Replace water filter	Genuine Kenmore refrigerator water filter WFCB
No start/no cool	Replace start relay	Refrigerator start relay kit 5304491941
Frost/defrost issues	Replace defrost thermostat	Refrigerator defrost bi-metal thermostat 5303918214
Dispenser not dispensing	Repair chute door sealing	Refrigerator dispenser ice chute door kit 241688401

Why it matters

Catching airflow, defrost, and water filter issues early helps prevent food spoilage, reduces ice and water dispenser failures, and can avoid extra strain on the compressor and electronic controls.

Last updated: February 2026

To replace the ice maker in your Kenmore Elite 25344503601 side-by-side refrigerator, we shut off power and the water supply, remove the ice bin, unplug the harness, remove mounting screws, swap the ice maker, then restore water and power and discard the first batches of ice.

Before you start (safety and prep)

• Unplug the refrigerator or switch off the breaker.
• Turn the household water shutoff valve OFF.
• Turn the ice maker On/Off switch OFF (the “0” position).
• Remove the ice storage bin by lifting up and out (do not use the chute as a handle).
• Wear gloves; surfaces around the chute and bin area can be sharp.

Replacement steps (typical side-by-side procedure)

1. Remove the ice bin and any shelves/buckets blocking access.
2. Disconnect the ice maker wiring harness plug.
3. Remove the mounting screws holding the ice maker to the freezer wall.
4. Lift the ice maker off the mounting tabs/bracket and remove it.
5. Set the new ice maker onto the tabs/bracket; reinstall screws.
6. Reconnect the wiring harness.
7. Reinstall the ice bin. If it will not seat, realign the auger by turning it in 90° turns until it fits.
8. Turn water ON, restore power, then switch the ice maker ON (the “I” position).

Water supply details that matter on this model

The 25344503601 manual specifies these water supply basics:

Item	Spec/requirement
Water pressure	30 to 100 psi
Supply line	1/4-inch (6.4 mm) OD copper tubing
Shutoff valve	Non self-piercing type

For diagrams and connection steps, follow the installation guide.

Why it matters

Correct shutoff, wiring reconnection, and bin alignment prevent leaks, dispenser jams, and noisy valve operation when the ice maker is ON without water.

If you are also troubleshooting dispenser drive issues, the refrigerator ice dispenser auger motor 242221501 is a common related part. For additional parts by model number, search on Sears PartsDirect.

Last updated: February 2026