Kenmore 66514579N612 dishwasher Parts

Yes. We still carry replacement parts for Kenmore dishwashers, including the Kenmore 66514579N612, as long as the part is still being manufactured and stocked. The key is matching parts by your full model number so you get the correct fit for items like racks, pumps, valves, and door hardware.

How to make sure you order the right part

Use your model number (66514579N612) and confirm the part location and description in the diagrams and parts list in the 66514579N612 owner's manual.

• Match by model number first, then confirm the part name
• Compare the old part to the listing (mounting points, connectors, length)
• Check whether your dishwasher uses a power cord or direct wire setup
• For installation-related items, follow local electrical and plumbing codes
• If you are replacing a water supply connection, note that many flexible braided inlet hoses are typically replaced every 5 years

Common Kenmore 66514579N612 parts customers replace

These are examples of parts we commonly see replaced on this model:

Symptom	Likely area	Example part for this model
Upper rack won’t stay level or rolls poorly	Rack adjusters/rollers	Dishwasher rack adjuster W10712395
Not draining	Drain system	Dishwasher drain pump (model-matched)
Not filling	Water supply	Dishwasher water inlet valve (model-matched)
Door won’t latch	Door hardware	Dishwasher door latch (model-matched)

Why it matters

Kenmore dishwashers are built with model-specific variations, even within the same series. Using the exact model number helps prevent ordering a similar-looking part that does not align with your rack rails, wiring harness, or water connections.

Helpful DIY reference

If your dishwasher is showing a code or beeping pattern, use Kenmore 665 model dishwasher error codes to narrow the problem to a fill, drain, heating, or control issue before you buy parts.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66514579N612 is usually worth it when the problem is a common wear item (rack parts, latch, hoses) and the repair cost stays well below the price of a new dishwasher; major motor or control failures can tip the decision toward replacement.

Quick way we decide: age + repair type + cost

• Under 8 years old: repairs are typically a good value.
• 8 to 12 years old: repair is worth it for mid-cost fixes; avoid stacking multiple big repairs.
• Over 12 years old: repair only if it is a small, targeted fix.
• One-time failure vs. repeat issues: repeated draining, leaking, or no-heat problems usually mean more parts are aging.
• DIY vs. service call: DIY can make many repairs cost-effective.

Common repairs that are usually worth it on 66514579N612

Symptom	Likely area	Example part for this model	Typical value call
Upper rack won’t stay up or rolls poorly	Rack adjusters/rollers/stops	Dishwasher rack adjuster W10712395	High
Door won’t latch or won’t start	Door latch	Dishwasher door latch WPW10653840	High
Not draining	Drain pump or drain hose routing	Dishwasher drain pump W10876537	Medium
Leaking at the bottom of the door	Lower door seal	Dishwasher door seal, lower W10909089	Medium

When replacement makes more sense

• The dishwasher needs a pump motor or electronic control board plus another major part.
• The tub or major structural components are damaged.
• You are paying for multiple service visits in a short period.

Why it matters

A targeted repair can restore cleaning and drying performance for a fraction of replacement cost, but large electrical or motor repairs on an older unit can lead to more downtime and additional failures.

Helpful references for this model

• Use the 66514579N612 installation guide to confirm safe electrical and plumbing requirements before any install-related work.
• If you are troubleshooting a flashing code or beeping, check Kenmore 665 model dishwasher error codes.

Last updated: February 2026

The model number for your Kenmore dishwasher is printed on the appliance’s model and serial tag. On most Kenmore 665-series built-in dishwashers, you’ll find that tag on the tub frame around the door opening; check the left or right side edge after you open the door. For diagrams and exact label locations, use the 66514579N612 installation guide.

Where to look (fast checklist)

• Open the dishwasher door fully.
• Look along the tub frame (the metal/plastic rim the door closes against).
• Check the left side first, then the right side.
• Look near the top edge of the opening if you do not see it on the sides.
• Wipe the area with a damp cloth so the numbers are readable.

What you should write down

Record these exactly as shown on the tag:

• Model number (example format: 665.XXXXXXX)
• Serial number
• Type or engineering code (if listed)

Item on tag	Why it matters
Model number	Matches you to the correct parts diagrams and fit-checked parts
Serial number	Helps confirm production series when parts changed mid-run
Type/engineering code	Helps narrow down compatible assemblies and revisions

Why it matters

Kenmore model numbers that look similar can use different racks, pumps, or seals. Using the exact model number helps ensure parts like a door latch, drain pump, or water inlet valve match your dishwasher correctly.

Last updated: March 2026