Do you need to oil the chain on an electric chainsaw?
Yes. Your Remington electric chainsaw model 107624-01 still needs bar-and-chain oil because the chain rides at high speed on the guide bar; oil reduces friction and heat, helps the chain cut smoothly, and prevents rapid wear.
What oiling does (and does not) do
Bar-and-chain oil is strictly for lubricating the chain and guide bar. It does not replace any internal motor lubrication.
- Reduces heat buildup at the bar rails and nose
- Helps prevent chain stretch and premature dulling
- Lowers the chance of binding and smoking during cuts
- Protects the bar from scoring and blueing
- Improves cutting speed and control
How to tell the chain is getting enough oil
Use these quick checks before and during cutting:
- Oil level drops in the reservoir after a few minutes of use
- The chain looks slightly wet, not dry and dusty
- You see a light oil line on a stump or cardboard after revving briefly
- The bar does not get excessively hot to the touch (after unplugging)
Common oiling problems and fixes
| Symptom | Most likely cause | What we do next |
|---|---|---|
| Chain looks dry | Empty reservoir or wrong oil | Refill with bar-and-chain oil; avoid thin substitutes |
| Oil leaks when stored | Overfilled tank or stored on its side | Store level; wipe excess; do not overfill |
| Chain smokes or turns blue | No oil flow or chain too tight | Check oiling, then set correct chain tension |
| Cuts crooked | Dull chain or uneven cutters | Replace or sharpen the chain |
When to replace the chain
If the cutters are worn, the chain stretches quickly, or it will not hold an edge, replacement is the fastest fix. For this model, we list a compatible 16-inch chain: chain 16" 91PX056G.
Why it matters
Running an electric chainsaw without bar-and-chain oil quickly overheats the bar and chain, which shortens the life of the cutting system and can make the saw harder to control.
Last updated: February 2026
Why does my electric chainsaw chain keep coming loose?
On a Remington 107624-01 electric chainsaw, a chain that keeps coming loose is caused by incorrect tensioning, installing the chain in the wrong direction or not fully seated on the bar, or normal chain stretch and bar wear that prevents the tensioner from holding.
Quick checks that fix most “loose chain” problems
- Unplug the saw first (or remove the battery if applicable) before touching the chain.
- Set tension with the bar nose lifted; hold the tip of the guide bar up while tightening so slack does not return when you start cutting.
- Seat the chain fully in the guide bar groove and on the drive sprocket before final tightening.
- Confirm chain direction; the cutters must face forward on the top run of the bar.
- Re-tension after the first minute of cutting; new chains commonly stretch quickly.
What to inspect if it loosens again
If the chain loosens repeatedly after correct adjustment, inspect these wear points:
| What to check | What you’ll notice | What it leads to |
|---|---|---|
| Chain stretch | Tension won’t hold, chain sags soon after tightening | Chain needs replacement |
| Guide bar groove/rails | Chain rocks side-to-side, uneven wear | Poor tracking, frequent loosening |
| Tensioner mechanism | Adjuster turns but chain barely moves | Tensioner not engaging properly |
| Bar mounting/clamping | Bar shifts when cutting | Tension changes under load |
Chain stretch is the most common cause
If your chain has been used a lot, it can stretch past the range the tensioner can take up. For this model, a correct replacement option is the chain 16" 91PX056G (part number 091375-02S).
Correct tension (practical rule)
We set tension so the chain is snug on the bar but still pulls around by hand with a gloved hand. A properly tensioned chain should lift slightly from the bar at the midpoint but the drive links should stay engaged in the groove.
Why it matters
A loose chain can derail, cut poorly, and accelerate wear on the guide bar, sprocket, and tensioner. Keeping tension stable improves safety and extends the life of your Remington electric chainsaw.
Last updated: February 2026
How do I find the model number on my 107624-01?
The model number for your Remington electric chainsaw is printed on the saw’s identification label (often called the rating plate). On model 107624-01, check the housing near the motor/handle area and confirm the full number exactly as shown before ordering parts like the chain 16" 91PX056G.
Where to look on the chainsaw
Check these common label locations on Remington electric chainsaws:
- Side of the main housing near the motor vents
- Near the rear handle or trigger area
- On the underside of the saw body (near where the bar mounts)
- Close to the power cord entry point
- Inside the side cover area (only after unplugging and removing the cover)
What to write down (so parts match)
Record the model information exactly as printed.
| Item to record | Example for your saw | Why it matters |
|---|---|---|
| Model number | 107624-01 | Ensures diagrams and parts lists match |
| Suffix/variant | Any extra digits/letters | Can change bar/chain fit |
| Serial number | Unique to your unit | Helpful for service history |
Quick tips if the label is hard to read
- Wipe the label with a damp cloth and mild soap; dry it fully.
- Use a flashlight at an angle to make stamped text easier to see.
- Take a close-up photo and zoom in.
- If the label is missing, match parts by comparing your bar length and chain specs to the parts list for 107624-01.
Why it matters
Electric chainsaw parts are fit-specific. A small model variation can change the correct chain pitch, gauge, and drive link count, so confirming 107624-01 helps you avoid ordering the wrong replacement chain.
Last updated: March 2026
