Whirlpool WDTA50SAHW0 dishwasher Parts

On a Whirlpool WDTA50SAHW0 dishwasher, the most common problems come from loading and detergent issues, a dirty filter, a blocked drain path (including the air gap), or the door not being latched and restarted correctly after opening. We recommend checking the basics first using the WDTA50SAHW0 owner's manual.

Quick checks that fix many problems

• Won’t start or won’t resume: Press Start/Resume, then push the door firmly closed within 4 seconds.
• Not filling: Confirm the water supply is turned on; make sure the overfill protection float moves freely.
• Not draining: Check and clean the drain air gap (if installed) and look for kinks or clogs in the drain hose.
• Not cleaning well: Verify the filter is installed correctly and clean it if needed; avoid blocking the spray arms.
• Not drying: Use rinse aid and a heated dry option; unload the bottom rack first to prevent water from dripping.
• Noisy: Reposition items that extend beyond the racks and hit the wash arms.

Symptom-to-cause guide

Symptom	Most likely cause	What to do first
Dishes still dirty	Filter dirty, poor loading, wrong cycle	Clean filter; reload; try a tougher cycle option
Water left in tub	Drain restriction	Check air gap and drain hose routing
Won’t fill	Water off, float stuck, suds	Turn water on; free float; reduce suds
Poor drying	No rinse aid, loading holds water	Add rinse aid; adjust loading and unloading order

Parts that commonly relate to these symptoms

If you find a mechanical issue during checks, these model-matched parts are often involved:

• Door won’t latch or cycle stops: dishwasher door latch WPW10653840
• Not draining (pump hums or won’t evacuate): dishwasher drain pump W10876537
• Not filling or fills slowly: dishwasher water inlet valve WPW10327249

Why it matters

Dishwashers depend on correct door closure timing, proper water fill, and a clear filtration and drain path. Fixing those basics first prevents repeat clogs, poor wash performance, and unnecessary part replacement.

Last updated: February 2026

On a Whirlpool WDTA50SAHW0 dishwasher, an F6 code points to a water fill problem: the dishwasher is not detecting the expected water coming in (or it is detecting an abnormal fill condition). The most common causes are a shutoff/low supply, a kinked hose, or a problem with the inlet valve.

Quick checks we recommend first

• Make sure the sink shutoff valve is fully open.
• Confirm the water supply line is not kinked or crushed behind the dishwasher.
• Check that the dishwasher door is closing and latching firmly; the unit will not run properly if the door is not fully latched.
• Cancel the cycle and let it drain completely, then restart the cycle (the control panel behavior and cancel/drain steps are outlined in the WDTA50SAHW0 owner’s manual).
• If the dishwasher recently had power interrupted, press Start/Resume and close the door promptly so the cycle can resume.

What to inspect if the code returns

If the basic supply checks look good and F6 comes back, focus on the fill path and the parts that control it.

Water supply and fill path

What to check	What you’re looking for	Why it matters
Shutoff valve	Fully open, good flow	Low flow can trigger fill errors
Supply line routing	No kinks, no pinches	Restriction reduces fill rate
Inlet connection	No leaks, secure fitting	Air leaks and restrictions affect filling

Parts commonly involved

• Water inlet valve operation and screen condition (a failed valve or blocked inlet screen can prevent filling).
• Wiring connections at the valve and control (loose connections can interrupt valve power).
• If you need the correct replacement valve for this model, match it to dishwasher water inlet valve WPW10327249.

Why it matters

A fill error stops the wash early, which can leave detergent undissolved and dishes dirty. Correcting the water supply issue also helps protect the pump and heating system from running under abnormal conditions.

Related help

For code patterns and what they mean across Whirlpool dishwashers, use our Whirlpool dishwasher error codes reference alongside the model’s manual.

Last updated: February 2026

Yes. Whirlpool manufactures dishwashers, and the Whirlpool WDTA50SAHW0 is one of their dishwasher models. For model-specific operation, cycle options, and care guidance, use the WDTA50SAHW0 owner's manual.

What this means for parts and service

When you own a Whirlpool dishwasher like WDTA50SAHW0, you can match replacement parts to the exact model so fit and electrical connections are correct.

• Use the full model number WDTA50SAHW0 when ordering parts.
• Find the model and serial tag inside the tub near the door (right or left side).
• Follow the Start/Resume timing rules; many Whirlpool models require closing the door within a few seconds after pressing Start/Resume.
• Use only UL Listed/CSA Approved electrical connection parts during installation.
• If the door will not latch or the unit will not start, check the latch and door closure first.

Common Whirlpool dishwasher parts customers replace

These are frequent wear items on WDTA50SAHW0-STYLE dishwashers:

Symptom	Likely area	Example part for this model
Door will not close or start	Door latch	Dishwasher door latch WPW10653840
Not draining	Drain system	Dishwasher drain pump W10876537
Poor drying	Heating circuit	Element assembly W10703867
Rack problems (sagging, not rolling)	Rack hardware	Dishwasher rack adjuster W10712395

Why it matters

Confirming Whirlpool is the manufacturer helps you use the correct Whirlpool procedures (controls, cleaning recommendations, and installation requirements) and select compatible OEM parts for the WDTA50SAHW0 dishwasher.

Last updated: February 2026

On a Whirlpool WDTA50SAHW0 dishwasher, the F6 E1 error is commonly tied to the door not being recognized as closed or the control not seeing the door switch signal. We fix it by confirming the door closes firmly, then checking the latch area and doing a simple reset.

Quick fixes to try first

• Press Cancel/Drain, close the door firmly, and let the 2-minute drain finish.
• Start a cycle again; press Start/Resume and close the door within 4 seconds (this model will not resume otherwise). See the WDTA50SAHW0 owner’s manual.
• Power reset: turn the dishwasher off at the breaker for 1 minute, then restore power.
• Remove anything that can keep the door from sealing (tall utensils, a rack not fully seated, a pan handle).
• Check for detergent buildup or debris around the latch strike and inner door edge.

Check the door latch and door closing

If the door feels “closed” but the dishwasher still throws F6 E1, focus on the latch mechanism.

• Inspect the latch opening for broken plastic, bent metal, or obstructions.
• Close the door slowly and listen for a solid latch “click.”
• If the latch is loose, cracked, or intermittent, replace the latch assembly: dishwasher door latch WPW10653840.

What to look for (symptom guide)

What you notice	Most likely cause	What we do
Start/Resume light flashes, won’t run	Door not closed in time	Close firmly within 4 seconds; retry per manual
Error appears when you bump the door	Weak or failing latch	Replace door latch
Door won’t stay shut	Misalignment or latch damage	Inspect strike/latch; replace latch if worn

Why it matters

The dishwasher will not run if the control thinks the door is open; it is a safety interlock. A marginal latch can also stop the cycle mid-wash and trigger repeated error codes.

Helpful reference

For code lookups and what they mean across Whirlpool dishwashers, use Whirlpool dishwasher error codes.

Last updated: February 2026