Maytag LA712 washer/dryer Parts

You can order replacement parts for your Maytag LA712 washer directly from our Maytag LA712 parts catalog, where we list model-matched components like switches, belts, hoses, clamps, and valves so you can repair with the right fit.

How to order the correct part for model LA712

• Match the full model number on the washer to LA712 before you buy.
• Identify the symptom first (no spin, no drain, no fill, leaking, lid won’t latch).
• Choose the part by function, then confirm it matches your washer’s design.
• If you are troubleshooting a no-start or no-spin issue, start with the lid switch W10820036.
• If you need a common wear item for drive problems, check the washer drive belt 12112425.

Common parts customers order for this Maytag washer

Problem you see	Part type to check	Example part for LA712
Washer won’t start or stops when lid opens	Lid switch	Lid switch W10820036
Won’t agitate or spin, burning rubber smell	Drive belt	Washer drive belt 12112425
Slow fill or no fill	Water inlet valve	Washer water inlet valve (listed for LA712)
Leaking at hoses	Hose clamp or drain hose	Drain hose, hose clamps

Why it matters

Ordering by the exact model (LA712) helps prevent returns and repeat repairs because older Maytag washer designs often use similar-looking parts that are not interchangeable.

Last updated: February 2026

A Maytag washer typically lasts 10 to 13 years. For your Maytag LA712, lifespan depends most on load size, how often it runs, and whether wear items (like belts and lid switches) get replaced before they cause bigger failures.

Typical lifespan ranges

Most washers fall into a few common “real world” ranges:

Washer type	Typical lifespan	What shortens it fastest
Top-load (belt-drive, older designs)	10 to 13 years	Overloading, worn belt, leaking seals
Top-load (newer designs)	8 to 12 years	Detergent buildup, unbalanced loads
Front-load	8 to 12 years	Door boot leaks, bearing wear

What helps a Maytag washer last longer

We see the longest life when owners keep loads reasonable and address small issues early.

• Avoid consistently overfilling; heavy loads strain the drive system and tub bearings
• Level the washer to reduce vibration and bearing wear
• Replace a slipping belt before it overheats or damages pulleys (example: washer drive belt 12112425)
• Fix “won’t spin” or “won’t start” symptoms quickly; a failing lid switch can stop cycles (example: lid switch W10820036)
• Check fill hoses for bulges or leaks and replace on a schedule

Quick signs your washer is nearing end of life

These symptoms often point to major wear (especially on older units):

• Loud roaring or grinding during spin (bearing wear)
• Repeated belt slipping or burning smell
• Water leaks from the tub area (seal or bearing issues)
• Frequent out-of-balance shaking even when leveled
• Slow fill or inconsistent water temperature (valve or supply issues)

Why it matters

A washer that is maintained and repaired early usually costs less to keep running. Once you have tub bearing or seal failures, repairs can become more involved, so catching noise, leaks, and spin problems early protects the drive system and cabinet.

Last updated: February 2026

Yes, it’s usually worth fixing a Maytag washer when the repair is a common wear item and the total repair cost stays under about half the price of a comparable replacement. For the Maytag LA712, simple fixes like a lid switch or drive belt often restore reliable operation without replacing the washer.

Quick way to decide (cost, age, and symptom)

Use these practical checkpoints before you buy parts:

• Repair cost target: parts plus labor under 50% of replacement cost
• Age rule: washers typically last 10 to 14 years; if yours is beyond that, prioritize only low-cost repairs
• Frequency: repeated breakdowns in a short period usually mean it’s time to replace
• Leak plus noise: multiple symptoms at once often point to bigger wear (bearings, seals)
• Safety and usability: if the lid won’t latch or the washer won’t start, a small part can be a high-value fix

Common LA712 repairs that are often “worth it”

These are the types of repairs we see pay off most often on this model:

• No start or stops mid-cycle: check the lid switch W10820036
• Won’t spin or weak agitation: inspect the washer drive belt 12112425
• Slow fill or no fill: check inlet screens and consider the washer water inlet valve 205613
• Drips at hose connections: replace clamps such as hose clamp WP596669

When replacement makes more sense

Major mechanical wear can push costs up quickly:

What you’re seeing	Likely area	Typical decision
Loud roaring in spin, persistent tub play	Bearings/tub support	Replace if repair cost is high
Multiple leaks plus poor spin	Seals, bearings, drive system	Replace if multiple major parts are needed
Burning smell, belt dust repeatedly	Drive system alignment/tension	Repair if limited to belt/tension parts

Why it matters

A targeted repair keeps a solid Maytag washer running and avoids the cost and hassle of replacement. The key is matching the symptom to the right part, then keeping the repair scope small and predictable.

Last updated: February 2026

The most common Maytag washer problem is a no-spin or no-drain condition. On the Maytag LA712, the most frequent causes are a lid safety switch that is not closing, a restricted drain path (hose or tub outlet), or a worn drive system such as the belt.

Quick checks we recommend first

• Confirm the lid closes firmly and the washer “clicks” into the closed position; a failed lid switch W10820036 can stop spin and sometimes drain.
• Look for a kinked or crushed drain hose behind the washer.
• Check the standpipe height and make sure the drain hose is not shoved too far down (can cause siphoning or slow drain).
• Run a spin cycle with an empty tub; listen for motor running but tub not turning (often points to a belt issue).
• If filling is the complaint, verify both hot and cold supply valves are fully open.

Common symptoms and the most likely causes

Symptom	What it usually points to	What to do next
Won’t spin	Lid switch not made, worn belt	Test lid switch; inspect belt condition
Won’t drain or drains slowly	Drain hose restriction, internal hose restriction	Inspect hose routing; check for clogs
Fills slowly or won’t fill	Inlet valve issue, supply problem	Check screens/hoses; consider valve replacement
Loud rumble in spin	Bearing wear	Stop use if severe; plan bearing service

Parts that commonly solve these problems on LA712

• Lid switch W10820036 (no spin, intermittent operation)
• Washer drive belt 12112425 (motor runs but basket does not spin well)
• Washer water inlet valve 205613 (no fill or weak fill)
• Drain hose WP22003410 (leaks, kinks, restrictions)

Why it matters

A washer that cannot spin or drain leaves clothes soaking wet and can strain the motor, belt, and bearings. Catching a simple lid switch or hose issue early often prevents bigger drive and tub wear.

Last updated: February 2026