Midea MAE70-S1402GPS-13 washer Parts

If your Midea washer model MAE70-S1402GPS-13 is not draining, the fix is usually a blocked drain path (pump filter, drain hose, or household standpipe) or a control or lid/door-related issue stopping the drain pump. Start with safe power-off checks, then clear restrictions before testing a drain/spin.

Quick checks that solve most “won’t drain” problems

• Unplug the washer (or switch off the breaker) for safety.
• Confirm the cycle actually reached drain; cancel and restart with Drain/Spin if available.
• Check the drain hose for kinks, crushing, or being pushed too far down the standpipe.
• Verify the standpipe or laundry sink is draining fast; a slow household drain can mimic a washer failure.
• Reduce the load size; heavy, waterlogged loads can prevent proper draining and spinning.

Clean the drain pump filter (most common cause)

Many washers trap coins, lint, and small items at the drain pump filter. When it clogs, the washer may stop with water in the tub.

• Place towels and a shallow pan under the front area.
• Open the access area (some models have a small door; others require removing a lower panel).
• Slowly loosen the filter cap to drain water, then remove debris.
• Reinstall the filter tightly and run a rinse or drain test.

For a step-by-step walkthrough, use cleaning the drain pump filter on a front load washer with no access door video.

What the symptoms usually mean

Symptom	Most likely cause	What to do first
Hums but won’t drain	Pump jam or clogged filter	Clean pump filter, check for obstructions
Drains slowly	Partial clog or restricted hose	Inspect hose and standpipe, clear blockage
Won’t drain and won’t spin	Lid/door lock issue or control problem	Re-seat door/lid, try a reset, then diagnose
Water backs up into tub	Household drain problem	Clear standpipe/sink drain

Why it matters

A washer that sits full of water can cause odors, mildew, and repeated drain pump strain. Clearing the drain path early helps protect the pump motor and gets your laundry routine back to normal.

If you want a broader diagnostic flow for common washer failures (including drain issues), use how to fix a washing machine.

Last updated: February 2026

On the Midea MAE70-S1402GPS-13 washer, an FD error indicates the control is detecting a sensor circuit problem and will typically stop the cycle for protection. The most productive fix is to reset power, then check wiring connections to the control and the related sensor(s).

What FD means in practical terms

FD is a fault code tied to a feedback signal the main control board expects to see from a sensor. When that signal is missing, out of range, or intermittent, the washer pauses or stops to prevent incorrect operation.

Common causes we see with FD-type sensor faults

• Loose or partially seated wire harness connector at the main control board
• Loose connector at the sensor (temperature, pressure, or similar feedback sensor)
• Pinched, rubbed-through, or broken wiring in the cabinet
• Moisture or corrosion at a connector
• Failed sensor or failed main control board input

Safe steps to try first

1. Unplug the washer (or switch off the breaker) for 2 to 5 minutes.
2. Restore power and run a quick cycle or rinse and spin.
3. If FD returns, disconnect power again before any inspection.

Quick troubleshooting map

When FD shows up	Most likely direction	What to check next
Immediately after starting	Connection or sensor circuit open/short	Reseat harness plugs at control and sensor
Mid-cycle or during spin	Intermittent connection from vibration	Look for pinched wires, loose connectors
Clears after reset but returns	Weak sensor or control input	Test sensor and wiring; replace failed part

Why it matters

A bad sensor signal can cause wrong water level or temperature decisions (depending on design), repeated shutdowns, and incomplete cleaning. Correcting the connection or replacing the failed component restores normal cycle operation.

Helpful DIY guidance

For a general, safe approach to accessing control-area connectors, use how to remove the main control board and user interface from a maytag epic z as a reference for the same type of steps used on many washers.

Last updated: February 2026

On the Midea MAE70-S1402GPS-13 washer, E2 is an error code, but the meaning is not universal across Midea washer platforms. The fastest way to get the washer running again is to treat E2 as a cycle-stopping fault and check the most common stop points: draining, door or lid status, load balance, and control connections.

What to check first (most common causes)

• Power reset: unplug for 2 minutes, then restart a normal cycle.
• Drain and spin: run a Drain/Spin type cycle; confirm water leaves the tub quickly.
• Load balance: redistribute bulky items (towels, blankets) and try a smaller load.
• Suds control: use HE detergent and reduce the dose; oversudsing can stall draining and spinning.
• Drain hose setup: remove kinks; keep the hose height and standpipe fit reasonable so it does not siphon or restrict flow.

Quick decision guide

What you notice when E2 appears	What it usually indicates	Best next step
Water remains in the tub	Drain flow problem	Check hose routing and household drain; then retry Drain/Spin
Stops during spin with banging	Out-of-balance load	Rebalance, reduce load size
Lots of foam, long cycle time	Oversudsing	Rinse out suds; switch to correct HE dosing
Happens after moving the washer	Loose connection or pinched hose	Inspect rear hose routing and wiring clearance

If you suspect a control or wiring issue

If E2 returns immediately after a reset and basic drain and load checks, the issue often involves the main control board, user interface, or wiring harness connections. A careful inspection for loose plugs or moisture at connectors is the next practical step.

• Use how to remove the main control board and user interface from a maytag epic z as a general reference for what “control access” looks like on many washers.

Why it matters

E2 stops the cycle to prevent poor draining, unsafe spinning, or control damage. Fixing the underlying cause prevents repeat shutdowns and reduces strain on the drain system and electronics.

Last updated: February 2026